Eiki Projector Lc Hdt2000 User Manual

61

This function prevents an unauthorized person from 
changing the screen logo.
 Off  .............  The screen logo can be changed freely from 
the Logo Menu (p.60).
  On  .............  The screen logo cannot be changed without a 
Logo PIN code.
If you want to change the Logo PIN code lock setting, 
press the SELECT button and the Logo PIN code dialog 
box appears. Enter a Logo PIN code by following the steps 
below. The initial Logo PIN code is set to "4321" at the 
factory.
Logo PIN code...

62

Settings
This function allows you to schedule a filter cleaning task. Select 
Filter control from the Setting menu and Yes in the confirmation 
box, or press the FILTER button on the remote control for 
approximately 5 seconds. 
✔Note
• The filter cleaning icon and “Cleaning is scheduled” message 
disappear 4 seconds after a filter cleaning task was scheduled.
• If a filter cleaning task is discontinued during the filter cleaning 
process, the filter cleaning unit resumes cleaning where it left 
off...

6

Settings
No  signal
4 : 50
Timer left before Lamp is off.
For reducing power consumption as well as maintaining 
the lamp life, the Power management function turns off the 
projection lamp when the projector is not operated for a 
certain period.
Select one of the following options:
 Ready  .................  When the lamp has been fully cooled 
down, the POWER indicator changes 
to green blinking. In this condition, the 
projection lamp will be turned on if the 
input signal is reconnected or...

64

Settings
Key lock
PIN code lock
This function locks the side control and remote control 
buttons to prevent operation by unauthorized persons.
  . . . . .Unlocked.
  . . . . .Locks the operation of the side control.
To unlock, use the remote control
    . . . . .Locks the operation of the remote 
control. To unlock, use the side control.
If the side control accidentally becomes locked and you do 
not have the remote control nearby or there is something 
wrong with your remote control, contact the...

65

When the projector is locked with a PIN code, the 
PIN code lock symbol appears in the Guide.
To change the PIN code lock setting
To enter a PIN code
When using side control
Use the Point ed buttons on the side control to select a number. 
Press the Point 8 button to fix the number and move the red 
frame pointer to the next box. The number changes to “✳.” 
Repeat this step to complete entering a four-digit number. After 
entering the four-digit number, move the pointer to “Set.” Press 
the SELECT...

66

Use the Point ed buttons to adjust the Projector ID.
Projector ID ... 1 - 999. (Factory default setting : Projector ID 1)
This feature allows users to set serial communication 
configuration (Projector ID) when several projectors are 
connected via the RS-232C terminal (serial port) of the 
projector.
Shutter function is available to block out light to the screen, 
so that the screen can be used for the other presenters.
Prohibits the shutter operation from the remote control and 
the...

67

When you want to make a digital processing of a projected 
image faster, set this function.
Use the Point ed buttons, select an item of Off/Low/Mid/
High.
Digital processing speed becomes fast by order of Low → 
Mid → High. High is the fastest.Fig.1
✔Note:
• The following functions are not available respectively when 
Video delay control is set to Low/Mid/High.
Low .....Keystone can not be selected.
Mid  ......Progressive and Noise reduction can not be selected.
High  .....  
Keystone, Progressive...

68

✔Note: 
• Normally, the filter cleaning unit automatically starts cleaning 
the mesh filter either while cooling down the projector after 
the power was turned off or after restarting the projector.
• When the icon as shown in Fig.3 appeared for the first time, 
replace the filters as soon as possible. If you turn off the 
projector before you replace the filters, the projector will turn 
off 3 minutes after the power is turned on next time.
This icon is warning you that the 
remaining time has...

69

Settings
This function allows you to change the presentation of the P-
timer and execute it.
Select one of the following options:
 Count up ............  The P-timer display 000:00 appears on 
the screen and the count starts (000:00–
180:00) 
 Count down  ....... The time set in the Timer setting appears 
on the screen and the countdown starts.
 Timer  ................. Use the Point ed buttons to set the 
Timer (1–180 Min). Only set to Count 
down, Timer is active. Factory default 
value is 10...

70

How to Overlap the Projection Images on a Screen 
You can obtain a seamless image by using the Edge Blending function which blends the images projected from multiple 
projectors and digitally dims the edges of the images and the Color Matching function which eliminates color unevenness. 
Follow the steps from 1 to 5 (or 8 if necessary) below to adjust multiple projector images.  
Configure the settings for screen size, image level, and lamp mode. These settings must match those for the rest 
of the...