Eiki Projector Lc Hdt2000 User Manual

91

When using the optional board (DVI) “AH-7222”, refer to the chart on the previous page.
When using other optional boards, refer to the charts below.
Supported Signal Format for Optional Board
ON-SCREEN 
DISPLA yRESOLUTIONH-Freq.(kHz)V-Freq.(Hz)
D-480i720x48015.73460.000
D-575i720x57615.62550.000
D-1035i1920x1035 i33.750 60.000 
D-1080i1920x1080 i33.75060.000 
1920x1080 i28.125 50.000 
D-720p1280x72045.00060.000
D-1080psf/241920x108027.000 48.000 
D-1080psf/251920x108028.125 50.000 
ON-SCREEN...

92

Appendix
Technical Specifications
Mechanical Information 
 Projector Type  Multi-media Projector 
  Dimensions (W x H x D)  25.59” x 13.74” x 32.09” (650.0 mm x 349.0 mm x 815 mm) 
 
  Net Weight  102.5lbs (46.5 kg)
 
  Feet Adjustment  ±3.0˚           
              
Panel Resolution 
 LCD Panel System  1.64” TFT Active Matrix type, 3 panels  
  Panel Resolution  2,048 x 1,080 dots
 
  Number of Pixels  6,635,520 (2,048 x 1,080 x 3 panels)           
             
Signal Compatibility 
 Color...

9

Optional Parts
The parts listed below are optionally available. When ordering those parts, specify the item name and Model No. 
to the sales dealer.
l The specifications are subject to change without notice.
l  LCD panels are manufactured to the highest possible standards. Even though 99.99% of the pixels are effective, a tiny 
fraction of the pixels (0.01% or less) may be ineffective by the characteristics of the LCD panels.
l   Each projector has its own characteristics.
       
When...

94

Configurations of Terminals
ANALOG TERMINAL(Mini D-sub 15 pin)
512341096781514131112
CONTROL PORT CONNECTOR (D-sub 9 pin)
DIGITAL (DVI-D) TERMINAL (DVI 24 PIN)
1917
21018
31119
41220
51321
61422
71523
81624
USB PORT(Series B)
2
3 4
1
13579111315171918161412108642
HDMI TERMINAL(19 pin Type A)
8 7 6 5 4 3 2 1
LAN PORT (RJ-45)
1TX+
2TX–
RX+
4- - -
5- - -
6RX–
7- - -
8- - -
Serial
1- - -
2RXD
TXD
4- - -
5SG
6- - -
7- - -
8- - -
9- - -
1Vcc
2– Data
+ Data
4Ground
1T.M.D.S. Data2–9T.M.D.S....

95

Appendix
Write down the PIN code number in the column below and keep it with this manual securely. If you forgot or 
lost the number and unable to operate the projector, contact the service center. 
Factory default set No:  1 2 3 4*
Factory default set No:  4 3 2 1*
*  S h o u l d   t h e   fo u r- d i g i t   n u m b e r   b e 
changed,  the  factory  set  number  will 
be invalid.
Put the label below (supplied) on in a prominent place of 
the projector’s body while it is locked with a PIN code....

96

Dimensions
Appendix
Unit: mm (inch)
620(24.41)
815(32.09)
420(16.54)
420(16.54)4–M84–M10312(12.28)148(5.83)
95(3.74)
37(1.46)183(7.21)
137(5.39)
550(21.65)
349(13.74)
349(13.74)
144(5.67)143(5.63)82(3.23)25(0.98)
35(1.38)
3º
301(11.85)
48(1.89)
25(0.98)650(25.59)
188.5(7.42)
198.5(7.82)
570(22.44)
40(1.58)
213(8.39)115(4.53)
224(8.82)
Threaded bores (for the ceiling mount)Diameter:  M8Depth: 32 mm (1.2598 inch)
Threaded  bores  (for  the  adjustable  feet  and  ceiling mount)Diameter:  M10Depth: 40...

97

On-BoardOptional Interface Board
Input1Input2Dsub-DVIComponent-S-videoSDIDualLinkSDI
Analog PCScartDigitalAnalog PC
ComponentVideo/S-VideoAnalog PCScartDigitalAnalog PC
ComponentVideo/S-videoDigitalDigital
On-BoardInput1
Analog PCo    o    o    o    o    o    o    o    o    o    o    o
Scarto    o    o    o        o        o        o    o       o        o        o    o
Digitalo    o    o    o    o    o    o   o       o    o    o    o   o
On-BoardInput2
Analog PCo    o    o    o    o    o    o    o...

98
Appendix
Serial Control Interface
This projector provides a function to control and monitor the projector's operations by using the RS-232C serial 
port.
Connect a RS-232C serial cross cable to SERIAL 
PORT IN on the projector and serial port on the PC
(See p.11).
1
2
3
Baud rate : 9600 / 19200 bps
Parity check  : none
Stop bit   : 1
Flow control  : none
Data bit   : 8
✔Note:
• The default of the baud rate is set to 19200 bps. If an 
error occurs in the communication, change the serial 
port and...

99
Appendix
Status Read Commands
The command is sent from PC to the projector with 
the format below;
     “CR” [Command] [CR]
        Command: one character (refer to the command 
table below.)
The projector decodes the command and returns the 
'Character string' with the format below;
Format
CommandFunctionReturn 
valueProjector status
CR0Status Read
00Power On
80Stand-by mode
40Countdown
20Cooling down
10Power Malfunction
28Cooling down at the temperature anomaly
24Cooling down at Power...

KL8B
U.S.A.
EIKI International, Inc. 
30251 Esperanza 
Rancho Santa Margarita 
CA 92688-2132 
U.S.A.
Tel :   800-242-3454 (949)-457-0200 
Fax :   800-457-3454 (949)-457-7878 
E-Mail : [email protected] 
Deutschland & Österreich 
EIKI Deutschland GmbH 
Am Frauwald 12 
65510 Idstein 
Deutschland 
Tel :   06126-9371-0 
Fax :   06126-9371-14 
E-Mail : [email protected] 
China
EIKI (Shanghai) Co., Ltd. 
Lakeside Oasis Middle Ring Business Centre 
Block 10. #16-07, 
1628, Jin Sha Jiang Road, 
Shanghai, 200333. China...