Eiki Projector EIP-XHS100 User Manual

41
Sharpness
The adjustment of sharpness primarily changes the value of high frequency detail. Use ◄ 
or ►to adjust it.
Noise Reduction
Use◄  or  ►to  adjust  the  noise  of  the  projected  image.  This  function  is  suitable  for  the 
elimination of image noise from interleaving SD input. Generally speaking, reducing image 
noise will lower the value of high frequency detail and make the image appear more 
mellow.
Aspect Ratio
This function allows user to adjust the picture’s Aspect ratio.
When...

42
Overscan
Some programs may display the edges of the image. Use this function to h\
ide the edge by 
choosing one of the following three options.
VGA Setup
Use this function to set up H-Total, H-Start, V-Phase and V-Start of VGA input.
Auto Sync
Use  this  function  to  EXCUTE  the  automatic  adjust  setting  of  black  level,  gain  for  the 
incoming signal. 
Off
4:3
16:10
4:3
Narrow
Normal
(720p) Crop
Zoom
Source image area
Noise edge
Screen (16:10)  

43
OSD Introduction – LAMPS
Mode
Use ◄ or ►function to select single or dual lamp mode.
Power
Use ◄ or ►function to select Eco, Normal, or Custom Power Level.
High Altitude
Use  this  function  to  switch  the  projector’s  cooling  fan  for  high-altitude  circumstances.  You 
can set it to Off or On. The default setting is Off.
Under normal circumstances, the projector will operate normally with thi\
s function set 
to Off. If you were to operate the projector in environment of excessive heat or in...

44
OSD Introduction - ALIGNMENT
Projection Mode
Use◄  or  ►function  to  select  the  projection  mode  (Front,  Rear,  Ceiling  +  Front,  Ceiling  + 
Rear).
Fan Mode
Use◄ or ► to set the fan mode to Normal, Up or Down.
 Normal: Normal fan speed.
  Up       :  Increase the fan speed.
  Down  :  Decrease the fan speed.
Lens Control
  Use  this  function  to  display  Lens  Control  window,  press  ◄,  ►,  ▲  or  ▼  to  adjust  lens 
shift,  Zoom  or  Focus.  Press  Enter  button  to  switch  window  for...

45
Center Lens
Execute to center the lens.
Warp
Use this function to correct image distortion.
Keystone
Use ◄ or ► to correct horizontal distortion. Press▲ or ▼to correct vertical distortion.
Rotation
Press◄ or ►to rotate the projected image.
The adjustable value is from -20 to 20 steps.
PPP
-20
20
0
Pincushion / Barrel
Use this function to correct pincushion or barrel distortion. The adjustable range is from 
-100 to 100 steps. Press ◄ to correct pincushion distortion, ► to correct barrel distortion....

46
Top Left Corner
 
PICTURE
        PICTURE
Top Right Corner
 
PICTURE         PICTURE
Bottom RightCorner
 
PICTURE        PICTURE
Bottom Left Corner
 
PICTURE        PICTURE
Reset
Set all values to factory defaults.
Blanking
Use this function to adjust the edges of the image and hide unwanted sec\
tions of the 
screen.
 
%ODQNLQJ$U
HD
To p
Use◄► to adjust the top blanking area on the projected image.
Bottom
Use ◄► to adjust the bottom blanking area on the projected image.
Left
Use ◄► to adjust the left...

47
Reset
Reset all the blanking functions to the default settings.
Edge Blend
Edge blend function allows multiple projector images to be seamlessly overlapped. To use 
this function, Edge Blend must be enabled on both projectors.
Blend Width
Press  Enter  to  display  Blend  Width  window,  use◄►  to  adjust  white  level  for,  bottom,  left 
and  right  blending  zone.  If  the Alignment  Pattern  is  enabled,  the  green  alignment  line  is 
moved according the setting value you made. Below is an...

48
Reset
This function resets Edge Blend to the factory default settings.
Align Pattern
Set to ON to Enable this function to use a test pattern to align and adjust multiple images, 
the alignment line is moved according to Blend Width setting.
OSD Introduction – CONTROL
Eco Network Power
Press◄► to set Standard or Eco network power.
Auto Power Off
The  default  value  is  OFF.  If  you  set  it  ON,  the  projector  will  automatically  shut  down  after 
20 minutes without input signal.
Auto Power On...

49
Trigger
 
The  projector  comes  with  one  set  of  Trigger  output.  You  can  configure  one  devices 
connected to the projector via the trigger port to be automatically turned on when the 
projector is on. There will be a 2-3 second delay prior to activation to prevent operation of 
this function when the user is choosing an aspect ratio.
5:4: Outputs 12V of power on Trigger when Aspect Ratio is set to 5:4.
4:3: Outputs 12V of power on Trigger when Aspect Ratio is set to 4:3.
16:10: Outputs 12V...

50
Model
The designated model number of the projector.
Serial Number
The designated serial number of the projector.
Software Version
The version of software installed on the projector.
Active/PIP Source
Displays the current Active/PIP sources.
Pixel Clock
Displays the pixel clock of the current input signal.
Signal Format
Displays the format of the current input signal.
H/V Refresh Rate
Displays the horizontal and vertical refresh rates for the current image.
Lamp 1 Time
Display the lamp 1 usage time....