Eiki Projector EIP-XHS100 User Manual

							41
Sharpness
The adjustment of sharpness primarily changes the value of high frequency detail. Use ◄ 
or ►to adjust it.
Noise Reduction
Use◄  or  ►to  adjust  the  noise  of  the  projected  image.  This  function  is  suitable  for  the 
elimination of image noise from interleaving SD input. Generally speaking, reducing image 
noise will lower the value of high frequency detail and make the image appear more 
mellow.
Aspect Ratio
This function allows user to adjust the picture’s Aspect ratio.
When Native input is 16:10, the images as following is the result of picture’s aspect ratio 
for your preference.
Normal output 16:10
Aspect ratio of output 
screen 5:4Aspect ratio of output 
screen 4:3Aspect ratio of output 
screen 16:9 Aspect ratio of output 
screen 1.88
Aspect ratio of output 
screen 2.35:1 Aspect ratio of output 
screen Letter BoxAspect ratio of output 
screen Auto Aspect ratio of output 
screen Real
Normal output 4:3 Aspect ratio of output 
screen 5:4Aspect ratio of output 
screen 4:3Aspect ratio of output 
screen 16:9 Aspect ratio of output 
screen 1.88
Aspect ratio of output 
screen 2.35:1 Aspect ratio of output 
screen Letter BoxAspect ratio of output 
screen Auto Aspect ratio of output 
screen Real  
						

							42
Overscan
Some programs may display the edges of the image. Use this function to h\
ide the edge by 
choosing one of the following three options.
VGA Setup
Use this function to set up H-Total, H-Start, V-Phase and V-Start of VGA input.
Auto Sync
Use  this  function  to  EXCUTE  the  automatic  adjust  setting  of  black  level,  gain  for  the 
incoming signal. 
Off
4:3
16:10
4:3
Narrow
Normal
(720p) Crop
Zoom
Source image area
Noise edge
Screen (16:10)  
						

							43
OSD Introduction – LAMPS
Mode
Use ◄ or ►function to select single or dual lamp mode.
Power
Use ◄ or ►function to select Eco, Normal, or Custom Power Level.
High Altitude
Use  this  function  to  switch  the  projector’s  cooling  fan  for  high-altitude  circumstances.  You 
can set it to Off or On. The default setting is Off.
Under normal circumstances, the projector will operate normally with thi\
s function set 
to Off. If you were to operate the projector in environment of excessive heat or in areas 
of high altitude, the projector may automatically shut down due to overheat. When this 
happens, you can enable this function by setting it to On to force the cooling fan to work at 
a higher speed to regulate the temperature inside the projector.
Note:
High altitude region refers to area with elevation over 5000 feet
Custom Power Level
Use  this  function  to  fine-tune  the  brightness.  You  can  set  power  range  from  80.4%  to 
100%.
Lamp 1 Status
Displays the Lamp 1 status.
Lamp 2 Status
Displays the Lamp 2 status.  
						

							44
OSD Introduction - ALIGNMENT
Projection Mode
Use◄  or  ►function  to  select  the  projection  mode  (Front,  Rear,  Ceiling  +  Front,  Ceiling  + 
Rear).
Fan Mode
Use◄ or ► to set the fan mode to Normal, Up or Down.
 Normal: Normal fan speed.
  Up       :  Increase the fan speed.
  Down  :  Decrease the fan speed.
Lens Control
  Use  this  function  to  display  Lens  Control  window,  press  ◄,  ►,  ▲  or  ▼  to  adjust  lens 
shift,  Zoom  or  Focus.  Press  Enter  button  to  switch  window  for  Zoom  &  Focus  adjustment 
or Lens Shift adjustment.
 
Lens Memory
Load Memory:    Select this item to load the lens settings.
Save setting:      You can save the lens settings.
Clear Memory:   Select this item to clear the lens settings.  
						

							45
Center Lens
Execute to center the lens.
Warp
Use this function to correct image distortion.
Keystone
Use ◄ or ► to correct horizontal distortion. Press▲ or ▼to correct vertical distortion.
Rotation
Press◄ or ►to rotate the projected image.
The adjustable value is from -20 to 20 steps.
PPP
-20
20
0
Pincushion / Barrel
Use this function to correct pincushion or barrel distortion. The adjustable range is from 
-100 to 100 steps. Press ◄ to correct pincushion distortion, ► to correct barrel distortion.
PPP
-100 100
0  
						

							46
Top Left Corner
 
PICTURE
        PICTURE
Top Right Corner
 
PICTURE         PICTURE
Bottom RightCorner
 
PICTURE        PICTURE
Bottom Left Corner
 
PICTURE        PICTURE
Reset
Set all values to factory defaults.
Blanking
Use this function to adjust the edges of the image and hide unwanted sec\
tions of the 
screen.
 
%ODQNLQJ$U
HD
To p
Use◄► to adjust the top blanking area on the projected image.
Bottom
Use ◄► to adjust the bottom blanking area on the projected image.
Left
Use ◄► to adjust the left blanking area on the projected image.
Right
Use ◄► to adjust the right blanking area on the projected image. Press  ◄►to  correct  top  left  corner  image 
distortion.
Press  ◄►to  correct  top  left  corner  image 
distortion.
Press  ◄►to  bottom  right  corner  image 
distortion.
Press  ◄►to  bottom  left  corner  image 
distortion.  
						

							47
Reset
Reset all the blanking functions to the default settings.
Edge Blend
Edge blend function allows multiple projector images to be seamlessly overlapped. To use 
this function, Edge Blend must be enabled on both projectors.
Blend Width
Press  Enter  to  display  Blend  Width  window,  use◄►  to  adjust  white  level  for,  bottom,  left 
and  right  blending  zone.  If  the Alignment  Pattern  is  enabled,  the  green  alignment  line  is 
moved according the setting value you made. Below is an example of setti\
ng blend width.
To
p Bottom Left
Right
Note:
Notice the green lines appear to indicate the edge of the screen and the\
 start/end of the blend zone.
Black Level Uplift
Black  Level  Uplift  is used  to compensate  for the lack  of pure  black  output from projectors, 
due to light leaking to the projection screen. When projecting black, the overlapping area 
where the two images overlap project twice the projectors’ black output levels. The solution 
is to adjust the Black Level Uplift.
Input signal is black, then increase the Black Level Uplift (Top, Bottom, Left, Right) until the 
non-overlap area’s brightness matches the overlap area.
Adjust  the  black  level  by  setting  the  Selected Area  (Top,  Bottom,  Left,  Right)  to  match 
the  black  levels.  You  can  adjust  all  colors  at  the  same  time  or  adjust  Red,  Green  or  Blue 
respectively.
Note:
Four corners, black level uplift adjustment function is not available.
Corner blending, black level uplift adjustment function is not available.
Black balance
Up
Down
Left
Right All
Red
Green
Blue
Red
Adjustment Select
0
0
0
0
0
0
0
0
0  
						

							48
Reset
This function resets Edge Blend to the factory default settings.
Align Pattern
Set to ON to Enable this function to use a test pattern to align and adjust multiple images, 
the alignment line is moved according to Blend Width setting.
OSD Introduction – CONTROL
Eco Network Power
Press◄► to set Standard or Eco network power.
Auto Power Off
The  default  value  is  OFF.  If  you  set  it  ON,  the  projector  will  automatically  shut  down  after 
20 minutes without input signal.
Auto Power On
The default value is Off. If you set it to ON, the projector will automatically start up when it 
is connected to the AC power.
Projector Control
Use ◄► to select RS232 or Network for the projector control.
Network
Use this function to display the network configuration.
Start Up Logo
Use◄► select on or off of the start up logo.  
						

							49
Trigger
 
The  projector  comes  with  one  set  of  Trigger  output.  You  can  configure  one  devices 
connected to the projector via the trigger port to be automatically turned on when the 
projector is on. There will be a 2-3 second delay prior to activation to prevent operation of 
this function when the user is choosing an aspect ratio.
5:4: Outputs 12V of power on Trigger when Aspect Ratio is set to 5:4.
4:3: Outputs 12V of power on Trigger when Aspect Ratio is set to 4:3.
16:10: Outputs 12V of power on Trigger when Aspect Ratio is set to 16:10.
16:9: Outputs 12V of power on Trigger when Aspect Ratio is set to 16:9.
1.88: Outputs 12V of power on Trigger when Aspect Ratio is set to 1.88.
2.35: Outputs 12V of power on Trigger when Aspect Ratio is set to 2.35.
Letterbox: Outputs 12V of power on Trigger when Aspect Ratio is set to Letterbox.
Native: Outputs 12V of power on Trigger when Aspect Ratio is set to Native.
Unscaled: Outputs 12V of power on Trigger when Aspect Ratio is set to Unscaled.
Auto: Outputs 12V of power on Trigger automatically.
Auto Search
Use ◄►to turn On/Off auto search.
Dynamic Black
Use◄► to turn On/Off dynamic black.
Language
See page 32 .
OSD Introduction – SERVICE
The functions covered in this unit relate to the display of some basic information about the 
projector.
Note:
Memory	of	the	custom	timing	files	will	be	erased	in	the	Factory	Reset	operation.  
						

							50
Model
The designated model number of the projector.
Serial Number
The designated serial number of the projector.
Software Version
The version of software installed on the projector.
Active/PIP Source
Displays the current Active/PIP sources.
Pixel Clock
Displays the pixel clock of the current input signal.
Signal Format
Displays the format of the current input signal.
H/V Refresh Rate
Displays the horizontal and vertical refresh rates for the current image.
Lamp 1 Time
Display the lamp 1 usage time. When you change the new lamp.
 
Lamp 2 Time
Display the lamp 2 usage time. When you change the new lamp.
Power On Time
Display the total On time for the projector.
Blue Only
This function displays only blue color to facilitate the process of imag\
e inspection for a 
service personnel.
Factory Reset
Restore  the  configurations  in  the  OSD  Menu  back  to  the  factory  default.  Note  that  this 
function will not apply to items including no signal, network, Projector control, startup Logo, 
language, High Altitude mode and lamp hours.
Note:
When	
Factory	 Reset	is	executed,	 all	source	 memories	 created	by	the	 projector	 (i.e.	timings	 files)	will	be	
erased.