Eiki Projector EIP-XHS100 User Manual

31
How to Operate the On-Screen Menu
 The  projector  has  an  On-Screen  Display  (OSD)  that  allows  you  to  adjust  image  and 
change settings.
OSD Operation
Following steps are a basic way for operating the OSD.
1.   Press the MENU button to open the OSD.
2.   Press ◄ or ► to select a title menu.
3.   Press ▲ or ▼ to select an item.
  The selected item will be highlighted.
4.   Press the Enter, and ▲ or ▼ to change or adjust the selected item.
5.   Press the MENU again or press the EXIT to close...

32
Changing the OSD Language
 The product can display the menus in English, French, Spanish, German, Portuguese, 
Simplify Chinese, Traditional Chinese, Japanese, Korean, Italian, Arabic or Russian. 
  Press  MENU  to  open  the  OSD.  Go  to  CONTROL  and  select  Language  then  press  the 
Enter. You can select a language there.  

33
OSD Tree
Main MenuSubmenu
INPUT Input Selection
HDMI
DVI
VGA
Component / BNC 
3G-SDI
PIP PIP Option Off/On
PIP Input HDMI
DVI
VGA
Component / BNC 
3G-SDI
PIP Swap Execute
Position Top Left
Top Right
Bottom Left
Bottom Right
Split L-R
Test Pattern Color Bar
Crosshatch
Burst
Red
Green
Blue
White
Black
Uncorrected Red
Uncorrected Green
Uncorrected Blue
H Ramp
Off
Color Space Auto
YCbCr
YPbPr
RGB-PC
RGB-Video
Input Lock Auto
48Hz
50Hz
60H
Background Logo
Blue
Black
White
Auto Sync Adjust Off
Auto
Always  

34
PICTUREPicture Mode
High Bright
Presentation
Video
Contrast 0-200
Brightness 0-200
PICTURE Adaptive Contrast
On
Off
Gamma Film
Graphics
Video
Linear
Color Color Temperature 5000K
6500K
7800K
9300K
Native
Trim Red Lift
Green Lift
Blue Lift
Red Gain
Green Gain
Blue Gain
Sharpness 0-200
Noise Reduction 0-200
Aspect Ratio 5:4
4:3
16:10
16:9
1.88
2.35
Letterbox
Native
Unscaled
Overscan Off
Crop
Zoom
VGA Setup H Total 0-200
H Start 0-200
H Phase 0-200
V Start 0-200
Auto Sync Execute
LAMP Mode
Single
Dual...

35
ALIGMENTProjection Mode
Front
Rear
Ceiling + Front
Ceiling + Rear
Fan Mode Normal
Lens Control Up
Down
ALIGMENT Lens Memory
Load Memory Memory set 1-10
Save Memory Memory set 1-10
Clear Memory Memory set 1-10
Center Lens Execute
Warp Keystone 
Rotation 
Pincushion
Barrel
Top Left Corner
Top Right Corner 
Bottom Left Corner 
Bottom Right Corner 
Reset
Blanking Top 
Bottom
Left
Right
Reset
Edge Blend Edge Blend On
Off
Blend Width To p
Bottom
Left
Right
Black Level Uplift All
Red
Green
Blue
Reset
Align...

36
ControlTrigger
1.88
2.35
Letterbox
Native
Unscaled
Auto
Control Auto Search
On
Off
Dynamic Black On
Off
Language English 
Français 
Español  
Deutsch
Português
简体中文
繁體中文
日本語
한국어
Italiano
الإنجليزية
русский
SERVICE Model
Serial Number
Software Version
Active/PIP Source
Pixel Clock
Signal Format
H/V Refresh Rate
Lamp 1 Time
x HRS
Lamp 2 Time x HRS
Power On Time x HRS
Blue Only On
Off
Factory Reset  

37
OSD Operation-INPUT
Input Selection
You can select the input source. 
HDMI
HDMI input.
DVI
DVI input.
VGA
Analog RGB.
Component / BNC
Analog / serial digital interface.
3G-SDI
Uncompressed digital video from a serial connection (coaxial)
TimingSDI Link mode Signal Standards Color EncodeSampling Structure Bit depthCable Length Tested
NTSC SD SMPTE 259M-C 270Mbps SD YCbCr4:02:02 10128m
PA L SD SMPTE 259M-C 270Mbps SD YCbCr4:02:02 10128m
1035i 60Hz HD-Single SMPTE 292M292M 1.5Gbps HD YCbCr4:02:02 10128m...

38
PIP
Use this function to display multiple windows each containing an image.
PIP Option
Use this to enable or disable the Picture In Picture function.
PIP Input
Press ENTER to display available sources for the sub picture then select a source.Note 
that unavailable input source of submenu are gray out and can not be selected. The 
available input source of sub picture is as below combination list.
Source
HDMI DVIVGA Component/BNC 3G-SDI
HDMI XX O O X
DVI XX O O X
VGA OO X XO
BNC OO X XO
3G-SDI XX O O...

39
Position
Use this function to select the location of the PIP window to Top left, Top Right, Bottom 
Left, Bottom Right, or Split L-R.
21
1
2
T
op Left
1
2
Bottom Left
1
2
Bottom Right Split L-R
1
2
Top Right
Test Pattern
Select  this  function  to  display  test  pattern,  press  ◄  or  ►  once  to  display  the  last  or  next 
pattern, press EXIT to exit test pattern.
Color Space
This  function  allows  you  to  change  component  and  RGB  input  sources.  You  can  select 
different color space...

40
OSD Introduction – PICTURE
Picture Mode
Use ◄ or ►to select the High Bright, Presentation and Video mode.
Contrast
Use ◄ or ► to adjust the contrast of the projected image.
Note:
Brightness and Contrast controls are interactive. The screen change to o\
ne may require a subtle change to 
the other in order to achieve the optimum setting
Brightness
Use  ◄  or  ►to  adjust  the  level  of  black  in  the  image  to  increase  or  decrease  image 
brightness.
Adaptive Contrast
Use ◄ or ►to adjust the...