Eiki Projector EIP-XHS100 User Manual

21
Positioning Projector
Picture Level and Pitch Adjustment
 The projection angle is adjustable up to 5 degrees upward and downward respectively 
by rotating front and rear. To raise the projector, rotate the front feet clockwise, rotate the 
rear foot clockwise to lower the projector.
Adjusting the Picture Orientation
  This projector is designed to be installed in one of four possible installation locations. 
Take  into  consideration  the  size  and  position  of  the  screen,  the  location  of  a...

22
Lens Shift Adjustment
 Projection lens can be moved up, down, right and left with the motor-dri\
ven lens shift 
function.  This  function  makes  the  positioning  of  images  easy  on  the  screen.  Lens  shift  is 
generally expressed as a percentage of the image height or width, see be\
low illustration.
Vertical / Horizontal Lens Shift
  For ceiling mounted projectors, the lens can be moved 50% (0.5V) downward, while the 
lens can be moved 50% (0.5V) up or down on a desktop mounted projector ....

23
Connecting to Computer
Cables used for connection•  HDMI Cable 
   (One cable is supplied, Other cables are not supplied with this proj\
ector)  
   
135791113151719
24681012141618
•  DVI Cable
•  BNC Cable(BNCx5)
•  VGA Cable (D-Sub 15 pin)
IN OUT
SDI
H
V
RGB
LAN
RS-232
HDMI
DVI-D B/PbG/YR/Pr
WIRED REMOTETRIGGER
BNC Cable
VGA  Cable
HDMI Cable
DVI Cable
Laptop computer
Desktop
Computer
24X DVD RW
Signal
Output
Analog
HDMI
Signal
Output
Signal
Output
Signal
Output
H
V
R/Pr
G/Y
B/PbDigital  

24
Connecting to Video Equipment
Cable used for connection
• Video Cable (BNCx3,  BNCx1)
•  DVI Cable
•  SDI Cable
•  HDMI Cable 
IN OUT
SDI
H
V
RGB
LAN
RS-232
HDMI
DVI-D B/PbG/YR/Pr
WIRED REMOTETRIGGER
SDI in
B/Pb
Digital Output
(HDCP compatible) Component Video Output
(B/Pb     G/Y    R/Pr)
SDI Out HDMI Output
G/YR/Pr
DigitalHDMI
Blu-ray Player Component Video output equipment
(Such as high-definition TV source)  

25
Trigger connection
 If your projection system includes a projector screen, screen cover or other 12V Trigger 
equipment, please connect such device/equipment to the projector’s 12V Trigger output as 
illustrated. After you have done so, your screen will lower automatically whenever you turn 
on your projector for your convenience.
IN OUTSDI
H
V
RG
B
LAN
RS-232
HDMI
DVI-DB /PbG /YR/Pr
WIRED REMO TETRIGGER
Screen  

26
RS-232 Connection
 Connect  a  PC  or  home  theater  control/automation  system  (if  present)  to  the  RS-232 
port on the projector. Use a standard, 9-pin serial cable, wired straight-through.
IN OUTTEJ
H
V
RG
B
LAN
RS-232
HDMI
DVI-DB /PbG /YR/Pr
WIRED REMO TETRIGGER
LAN Connection
IN OUTTEJ
H
V
RG
B
LAN
RS-232
HDMI
DVI-DB /PbG /YR/Pr
WIRED REMO TETRIGGER
PC
Router  

27
Connecting to wired remote controller
 If infrared remote signals cannot reach the projector due to obstructions, you can use 
the remote control as a wired remote control.
IN OUTTEJ
H
V
RG
B
LAN
RS-232
HDMI
DVI-DB /PbG /YR/Pr
WIRED REMO TETRIGGER  

28
Connecting the AC Power Cord
 This projector uses nominal input voltages of 100-240 VAC. It is designed to work with 
single-phase power systems having a grounded neutral conductor. 
To reduce the risk of electrical shock, do not plug into any other type of power system. If 
you  are  not  sure  of  the  type  of  power  being  supplied,  consult  your  authorized  dealer  or 
service  center.  Connect  the  projector  with  all  peripheral  equipment  before  turning  on  the 
projector.
Note
Unplug...

29
Basic Operation
Turning On the Projector
 ①Complete peripheral connections (with a computer, VCR, etc.) before turning on the 
projector.  ②Connect the projector’s AC power cord into an AC outlet and turn on the MAIN 
ON/OFF  Switch.  ③Press the "POWER" button on the side controller or On button on the 
remote  control. The  LAMP  indicator  flashes  green  and  the  cooling  fans  start  to  operate,  it 
will take a few seconds to display the projected image on the screen.
POWER
MENU EXIT...

30
Selecting an Input Source
 When you turn on the projector, it switches to the last selected input and waits for a 
valid signal. Press INPUT on the remote control or control panel to switch an input source 
directly.
POWER
MENU EXIT
INPUT
AUTO SYNC ASPECT
ENTER
Selecting a Aspect Ratio
Press ASPECT to adjust the aspect ratio of projected image.
POWER
MENU EXIT
INPUT
AUTO SYNC ASPECT
ENTER