Eiki Projector EIP-UJT100 User Manual

							61
3. 
Insert the new filters into the machine.  
Black side Black side
White side
xWhite side
x
3243411700
3243270701
4. 
Tighten the screws on the filter cover. 
ORDER REPLACEMENT Filter
Replacement filter can be ordered through your dealer. 
When ordering a filter, give following information to the dealer.
Replacement Filter P/N: 3243270701(Rear), 3243411700(Front)  
						

							62
Appendix
Technical Specification
ModelEIP-UJT100
Display Type DLP
Native Resolution WUXGA (1920 x 1200)
Maximum Resolution WUXGA (1920 x 1200)@60Hz
Lamp Life and Type 2000hours(Normal 465W), 2500hours(ECO 360W)
Aspect Ratio Native, Unscaled, 5:4, 4:3, 16:10, 16:9, 1.88, 2.35 and Letterbox
Lens Shift Range V(-25%~50%), H(+/-10%)
Keystone Correction Vertical: +/-20° Horizontal:+/-35°
Synchronization Vertical: 23.98 - 120 Hz
Horizontal: 15.63 - 91.15kHz
Edge Blending Yes (built-in)
Video Compatibility SDTV(480i/576i), EDTV (480p/576p), HDTV (720p, 1080i/p), NTSC/NTSC\
 4.43
 
PAL B/G/H/I/ M/N 60, SECAM
I/O Connection Ports HDMIx1, RGB/H/Vx1, YPbPrx1, VGAx1, DVI-Dx1, SDIx1, HDBaseTx1, SYNC INx1, 
SYNC OutX1,  R/C INx1, 12V-Triggerx2, RS-232x1, LANx1
Projection Method Table Top, Ceiling Mount (Front or Rear)
Dimensions (W x D x W) 550x505x250mm (21.7”x19.9”x9.8”)
Weight (Without Lens) 37kg (81.4lbs)
Power Supply AC 100-240V, 50/60Hz
Power Consumption Input Voltage
Normal Mode ECO Mode
220V 1140W 895W
110V 1230W 955W
Standby: 5W (LAN ON)
Standard Accessories AC Power Cord(USA) x2, AC Power Cord(EU) x1, AC Power Cord (China) x1
 
Remote Control x1, Owner's Manual (CD) x1, Quick Start Guide x1  
RoHS Card for China x1, QC Pass Card for China x1, Warranty Card for China x1  
Warranty Card for USA x1, Battery AA x2, Wired Remote Cable x1
Optional Accessories Interchangeable Lens (x6)
Replacement LampReplacement Filter  
						

							63
Product Outline Dimension
270
499.8
220
105
160
633.4
Mounting bracket screw hole (M6)
These screw holes are used to mount the 
projector to its designated mounting bracket 
using 6 M6x15 screws. The dimensions of the 
screw holes are shown in the picture below.
EIP-UJT100  
						

							64
Support Timing List
Signal FormatResolutionFrame 
Rate 3 RCA
5BNC
HD15- 
RGBHV HD15
 
YUV HDMI
SDI
Y-Pr-Pb Y-Pr-Pb RGBYUV
YUVYUV
8 bit 10 bit 12 bit
PC 640x480
59.94 VV V
640x480 74.99 VV V
640x480 85 VV V
800x600 60.32 VV V
800x600 75 VV V
800x600 85.08 VV V
848x480 47.95 VV V
848x480 59.94 VV V
1024x768 60 VV V
1024x768 75 VV V
1024x768 85 VV V
1280x720 47.95 VV V
1280x1024 60.02 VV V
1280x1024 75.02 VV V
1280x1024 85.02 VV V
1600x1200 60 VV V
1920x1080 47.95 VV V
1680x1050 59.94 VV V
1920x1200 50 VV V
1920x1200 59.94 VV V
1920x1200 60 VV V
1400x1050 60 VV V
1366x768 60 VV
1440x900 60 VV
1280x768 60 VV
1280x800 60 VV
1280x960 60 VV
Apple Mac 640x480
66.59 VV
832x624 74.54 VV
NTSC NTSC 
{M, 4.43) 59.94
PA L PA L
 
 (B, G, H, I) 50
PAL (N) 50
PAL (M) 59.94
SECAM SECAM (M) 50
SDTV RGBS
50
480i 59.94 V V
1440x480i 60 VVVV
1440x576i 50 VVVV
576i 50V V
EDTV 480p
59.94 VVVVVVVV
576p 50V VVVVVVV
HDTV 1035i
60V VVVVVVVV
1080i 50V VVVVVVVV
1080i(Aus) 50V VVVVVVVV
1080i 59.94 VVVVVVVVV
1080i 60V VVVVVVVV
720p 50V VVVVVVVV
720p 59.94 VVVVVVVVV
720p 60V VVVVVVVV
1080p 23.98VVVVVVVVV
1080p 24V VVVVVVVV
1080p 25V VVVVVVVV
1080p 29.97VVVVVVVVV
1080p 30V VVVVVVVV
1080p 50V VVVVVVVV
1080p 59.94VVVVVVVVV
1080p 60V VVVVVVV
V
new for SDI 1080sf
30 V
1080sf 25 V  
						

							65
SDI Format
TimingSDI Link modeSignal Standards Color
Encode Sampling
Structure Bit Depth
NTSC SDSMPTE 259M-C 270Mb
ps SDYCbCr4:2:210
PAL SDSMPTE 259M-C 270Mb
ps SDYCbCr4:2:210
1035i60 HDSMPTE 292M 1.5Gb
ps HDYCbCr4:2:2 10
1080i59 HDSMPTE 292M 1.5Gb
ps HDYCbCr4:2:2 10
1080i60 HDSMPTE 292M 1.5Gb
ps HDYCbCr4:2:2 10
1080P30 HDSMPTE 292M 1.5Gb
ps HDYCbCr4:2:2 10
1080P25 HDSMPTE 292M 1.5Gb
ps HDYCbCr4:2:2 10
1080i50 HDSMPTE 292M 1.5Gb
ps HDYCbCr4:2:2 10
1080P24 HDSMPTE 292M 1.5Gb
ps HDYCbCr4:2:2 10
720P60 HDSMPTE 292M 1.5Gb
ps HDYCbCr4:2:2 10
720P50 HDSMPTE 292M 1.5Gb
ps HDYCbCr4:2:2 10
1080Sf25 HDSMPTE 292M 1.5Gb
ps HDYCbCr4:2:2 10
1080Sf30 HDSMPTE 292M 1.5Gb
ps HDYCbCr4:2:2 10
1080P50 3G Level 
ASMPTE 424M 3Gbps YCbCr4:2:2 10
1080P59 3G Level 
ASMPTE 424M 3Gbps YCbCr4:2:2 10
1080P60 3G Level 
ASMPTE 424M 3Gbps YCbCr4:2:2 10
1080P50 3G Level BSMPTE 424M 3Gb
ps YCbCr4:2:2 10
1080P59 3G Level BSMPTE 424M 3Gb
ps YCbCr4:2:2 10
1080P60 3G Level BSMPTE 424M 3Gb
ps YCbCr4:2:2 10
Test Cable: Belden 1694
A
DVI dual-link for 3D 
Signal Type Resolution Frame rate DVI
single-link DVI 
dual-link 3D
Reference
PC 1920x 1080
120Hz VV
1920x 1080 100Hz VV
1920x1200 120Hz VVReduced Blanking
1920x1200 100Hz VVReduced Blanking
1920x 1080 60HzV
1920x1200 60HzV Reduced Blanking  
						

							66
Projector Control via LAN
The projector supports to control the projector through the network. Before using this 
function, please set up the network configuration of your personal computer .
1.  Set up network configuration.  
The default IP address of the projector is 192.168.0.100, please follow below steps to\
 
set the network configuration.  
Connect RJ-45 cable from PC to the LAN connector on the projector. 
HDMI IN VGA ING/YB/Pb R/Pr DVI-D IN
H V
RS-232C
1
2R/C IN
12V Trigger OUT
YPb Pr INOUT
SYNC
LAN
 
 
2.  Set up Internet Protocol (TCP/IP) Properties in your PC as below:  
 
Recommended PC setting  
  
IP Address : 192.168.0. 99. 
Subnet       : 255.255.255.0
Default settings for the projector  
IP Address :  192.168.0.100  
Subnet       :  255.255.255.0
   
						

							67
Open a web browser on your PC and type the IP address of the projector      
  (192.168.0.100), IP configuration will be shown on the web page.
Set the IP address and subnet mask and click SAVE to confirm the configuration. Projec-
tor Web Control will show below message for confirmation.
“The projector IP will be changed and the connection to the projector will be lost, do you 
want to continue ?
Select "Yes" to confirm the changes, "No" to cancel.Note: 
Make sure the IP address of the projector and PC are in the same network group.  
						

							68
Using Projector Web Control
 
■ Source/General  
Use this page to control the general settings of the projector such as p\
ower on/off, 
source….etc. 
Note:
If projector control option is selected to RS232, the web control will be interrupt. Network control has 
to be enabled from the projector’s OSD menu before connecting to projector web control.
 
■ Image Setting  
Click arrows to adjust the image settings such as Brightness, Sharpness…\
etc. on the 
web page.  
						

							69
 
■ Lens Adjustments  
This page allows you to adjust Zoom, Focus and Lens shift. The operation is similar to 
control the projector by the remote control or control panel on the proj\
ector, click arrows  
to adjust the settings. 
 
■ Geometry Adjust  
Click the arrow buttons to adjust Blanking, Warp, Four Corner, and click the option 
to select the aspect ratio setting. Click Reset option to reset Blanking\
 or Warp to the 
default setting.   
						

							70
 
■ Edge Blend  
Click Status option to enable or disable Edge Blend function. When Edge \
Blend is 
disabled, the other options are unavailable and N/A is shown on the column. The other 
options are available only when Edge Blend is enabled.  
 
■ Advance Control  
This page allows you to select color temperature or adjust black balance\
 or white 
balance. Click the option to select Color Temp. or arrow button to adjust the setting.