Eiki Projector EIP-UJT100 User Manual

							31
Selecting an Input Source
When you turn on the projector, it switches to the last selected input and waits for a val-
id signal. Press the “INPUT” on the remote control or control pane\
l to switch to an input 
source directly.  Refer to  page 17 button 1-5 for default input setting and these setting 
are changeable, Refer to  Page 54 Button 1~5
ENTER
INPUT
STANDBY
>
>
>32
1
HDBaseT
HDMI
RGBHV DVI
VGA
POWER
INPUT
ON
OFF
FOCUSFOCUS
ZOOMLENS CONTROL
45
Selecting a Aspect Ratio
Press ASPECT to adjust the aspect ratio of the image. For detail information, refer to 
Page 40 Aspect Ratio
1
3
2
1
ASPECT
RATIO
AUTO IMAGE
HDBaseT
HDMI
RGBHV DVI
VGA
PAUSE
TEXT
MENU
SHARPNESS
CONTRAST BRIGHTNESS
FOCUSFOCUS
ZOOM
ZOOM
LENS CONTROL
45  
						

							32
How to Operate the OSD Menu
The projector has an On-Screen Display (OSD) that allows you to adjust the image and 
change settings.
OSD Operation
Following steps are a basic way for operating the OSD.
1.  Press the MENU button to open the OSD.
2.  Press ▲ or ▼ to select a title menu.
3.  Press ◄ or ► to select an item.  
The selected item will be highlighted.
4.  Press the Enter, and ▲ or ▼ to change or adjust the selected item.
5.  Press the MENU in the monent move to upper menu.  
ERRORMENU
ON
>
>
>
LED
STATUS
1
3
2
1
ASPECT
RATIO
AUTO IMAGE
RGBHV
DVI
PAUSETEXT
MENU
SHARPNESS
CONTRAST BRIGHTNESS
FOCUSFOCUS
ZOOM
ZOOM
LENS CONTROL
45  
						

							33
Changing the OSD Language
The product can display the menus in English, French, Spanish, German, Portuguese, 
Simplify Chinese, Traditional Chinese, Japanese or Korean. 
Press the “MENU” to open the OSD. Go to SYSTEM and select Language then press 
the Enter. You can select a language there.  
						

							34
OSD Tree
Main MenuSub-menu
MAIN Input Selection
HDMI
HDBaseT
VGA
Y/Pb/Pr
RGBHV, Y/Pb/Pr
3G-SDI
3D DVI
Color Space Auto
REC709
REC601
RGB-PC
RGB-Video
Input Locking Auto
48Hz
50Hz
60Hz
Auto Power Off On
Off
Auto Power On On
Off
No Signal Logo
Blue
Black
White
Auto  Image Adjust Off
Auto
AlwaysMain MenuSub-menu
PICTURE Contrast
0-200
Brightness 0-200
Sharpness 0-200
Noise Reduction 0-200
Color Temperature 3200K
5400K
6500K
9300K
Native
Input Balance Black Balance Offset
  Red Offset
  Green Offset
  Blue Offset
White Balance
  Red Gain
  Green Gain
  Blue Gain
Aspect Ratio 5:4
4:3
16:10
16:09
1.88
2.35
Letterbox
Native
Unscaled
Timings H Total
H Start
H Phase
V Start
Auto Sync Execute
LAYOUT Overscan
Off
Crop
Zoom
Main Select HDMI
HDBaseT
VGA
Y/Pb/Pr
RGBHV, Y/Pb/Pr
3G-SDI
PIP Select HDMI
HDBaseT
VGA
Y/Pb/Pr
RGBHV, Y/Pb/Pr
3G-SDI
PIP Position Top Left
Top Right
Bottom Left
Bottom Right
Split L-R
PIP On
Off  
						

							35
Main MenuSub-menu
LAMPS Power
ECO
Normal
Custom Level
Mode Single
Dual
High Altitude On
Off
Custom Power Level 78.3%~100%
Lamp1 Status On / Off
Lamp2 Status On / Off
Lamp1 Run Time XX HRS
Lamp2 Run Time XX HRS
ADVANCED Rear Projection
On
Off
Ceiling Mode On
Off
Lens Control Zoom / Focus
Shift H/V
Dynamic Contrast On
Off
Gamma 1.8
2.0
2.2
2.35
2.5
DICOM SIM.
Test Pattern Color Bar
Cross hatch
Half scanning
Red 
Green
Blue
White
Black
Red
Green
Blue
Gray Scale
Color Gamut Native
EBU
SMPTE
CustomMain MenuSub-menu
ADVANCED Custom Color 
 
Gamut Red x
Red y
Green x
Green y
Blue x
Blue y
Cyan x
Cyan y
Magenta x
Magenta y
Yellow x
Yellow y
White x
White y
Reset
Center Lens Execute
Warp Keystone
Rotation
Pincushion / Barrel
Top Left Corner
Top Right Corner
Bottom Left Corner
Bottom Right Corner
Reset
Blanking To p
Bottom
Left
Right
Reset
Edge Blending Status
White Level
Black Level
Reset
Adjust Lines  
						

							36
Main MenuSub-menu
SYSTEM IR Address
1
2
Eco Network Power On
Off
Network Network Status
  IP Address
  Subnet Mask
  Gateway
  DHCP
Network Setting
  IP Address
  Subnet Mask
  Gateway
  DHCP
Menu Position Top Left
Top Right
Bottom Left
Bottom Right
Center
Start Up Logo On
Off
Start Up Chime On
Off
Button 1 HDMI
HDBaseT
VGA
Y/Pb/Pr
RGBHV, Y/Pb/Pr
3G-SDI
3D DVI
Button 2 HDMI
HDBaseT
VGA
Y/Pb/Pr
RGBHV, Y/Pb/Pr
3G-SDI
3D DVI
Button 3 HDMI
HDBaseT
VGA
Y/Pb/Pr
RGBHV, Y/Pb/Pr
3G-SDI
3D DVI
Button 4 HDMI
HDBaseT
VGA
Y/Pb/Pr
RGBHV, Y/Pb/Pr
3G-SDI
3D DVIMain MenuSub-menu
SYSTEM Button 5 HDMI
HDBaseT
VGA
Y/Pb/Pr
RGBHV, Y/Pb/Pr
3G-SDI
3D DVI
Trigger 1 Auto
5:4
4:3
16:10
16:09
1.88
2.35
Letterbox
Native
Unscaled
Trigger 2 Auto
5:4
4:3
16:10
16:09
1.88
2.35
Letterbox
Native
Unscaled
Auto Source On
Off
Language English
Français
Español
Deutsch
Português
简体中文
繁體中文
日本語
한국의
SERVICE Model
Serial Number
Software Version
Active/PIP Source
Pixel Clock
Signal Format
H/V Refresh Rate
Lamp 1 Run Time
x HRS
Lamp 2 Run Time x HRS
Lamp Hour Reset Reset Lamp 1
Reset Lamp 2
Projector Run Time
Blue Only On
Off
Factory Reset  
						

							37
OSD Operation-MAIN
Input Selection
You can select an input source. 
 
■ HDMI:  HDMI input.
 
■ HDBaseT:  HDBaseT input.
 
■ VGA:  Analog RGB.
 
■ Y/Pb/Pr:  YPbPr input.
 
■ RGBHV, Y/Pb/Pr:  Analog RGB / Component.
 
■ 3G-SDI:  Uncompressed digital video from a serial connection (coaxial)
 
■ DVI-D (3D DVI):  Use this DVI dual link to connect to a stereo 3D source – it is usua\
lly a 
computer with 3D Graphics card, and 3D applications.
Below information is the DVI-D (3D DVI) format:
Signal Type ResolutionFrame rate DVI
single-link DVI 
dual-link 3D
Reference
PC 1920x 1080
120Hz VV
1920x 1080 100Hz VV
1920x1200 120Hz VVReduced Blanking
1920x1200 100Hz VVReduced Blanking
1920x 1080 60HzV
1920x1200 60HzV Reduced Blanking
Note:
Signals are not supported for EIP-UJT100, if it is not in the table.  
						

							38
Color Space
This function allows you to change component and VGA input sources. You can select 
different color space for different color performance. 
 
■  Auto:  The default setting is Auto. 
HDMI:  If the Auxiliary Video Information (AVI) contains color space and/or range data, 
the EIP-UJT100 uses that information to switch to corresponding color sp\
ace.   
RGB:  If Hsync or Vsync signals are present, the projector will switch to RGB\
-PC color 
space.   
Component:  For SDTV and EDTV resolutions, the EIP-UJT100 uses the REC601 color 
space. For all other resolutions REC709 is used.
In most cases, the Auto setting determines the correct color space. If it does not, you can\
 
use a specific color space. Choose one of the following:
 
■ REC709:  sets the color space matrix to that defined in ITU-R BT.709.
 
■ REC601:  sets the color space matrix to that defined in ITU-R BT.601.
 
■ RGB-PC:  uses RGB color space and sets black at 0,0,0 RGB and white at 255,255,2\
55 
RGB, assuming an 8-bit image.
 
■ RGB-Video:  uses RGB color space and sets black at 16,16,16 RGB and white at 
235,235,235, assuming an 8-bit image, to correspond to the luminance   values defined 
in digital component standards.
Input Locking
Use this function to lock a source to an internal sync signal (Auto, 48Hz, 50Hz, or 60Hz). 
Auto setting locks the sync signal to the current source.
Auto Power Off
The default value is OFF. If you set it ON, the projector will automatically shut down after 
20 minutes without input signal.
Auto Power On
The default value is Off. If you set it to ON, the projector will automatically start up when 
it is connected to the AC power.
No Signal
Use this function to specify the content or color to be displayed on the blank screen 
when no input signal is available. You can choose from Logo, Blue, Black, White. The de-
fault value is Logo.  
						

							39
Auto image Adjust
Set the timing of the Auto image Adjust function for(Resync on page 41) below 3 
modes:
 
■ Off:  Auto image function is not executed.
 
■ Auto:  Use the parameters that users used last time.  
The adjusted parameters are stored in the projector, 5 resolution data for each digital 
and analog inputs. If there is no record of parameters, auto image funct\
ion will be   
executed.
 
■ Always:  Auto image function is executed automatically when the input source is   
selected.
OSD Operation-PICTURE
Contrast
Use ◄ or ► to adjust the contrast of the projected image. Adjustable value: 0 to 200.
Note:
Brightness and Contrast controls are interactive. The screen change to one may require a subtle 
change to the other in order to achieve the optimum setting.
Brightness
Use  ◄  or  ►to  adjust  the  level  of  black  in  the  image  to  increase  or  decrease  image 
brightness. Adjustable value: 0 to 200.
Sharpness
Use  ◄  or  ►  to  adjust  the  adjustment  of  sharpness  primarily  changes  the  value  of  high 
frequency detail. Adjustable value: 0 to 200.  
						

							40
Noise Reduction
Use◄  or  ►to  adjust  the  noise  of  the  projected  image.  This  function  is  suitable  for  the 
elimination of image noise from interleaving SD input. Generally speaking, reducing image 
noise will lower the value of high frequency detail and make the image appear more mel-
low. Adjustable value: 0 to 200.
Color Temperature
Use  ◄  or  ►  to  adjust  the  color  temperature  3200K,  5400K,  6500K,  9300K  or  Native  of 
the projected image.
This refers to the control of color imbalance in the darker areas of the projected image. 
It is recommended that you use an external test image with many areas of dark and gray 
colors (i.e. an image of 30IRE-window). If you notice minimal amount of red, green or blue 
in the gray areas, adjust the offset of the corresponding color accordingly. This function will 
shift the entire color spectrum for the whole image and change its brigh\
tness.
Input Balance
To adjust Black and White balance.
Black Balance : Adjust R/G/B color offset of image that will control dark areas.  
   White Balance : Adjust R/G/B color gain of image that will control bright areas.
Aspect Ratio
This function allows user to adjust the picture’s Aspect ratio.
When Native input is 16:10, the images as following is the result of picture’s aspect ratio 
for your preference.
Aspect Ratio of output
screen 16:9Original Aspect Ratio of output
screen 5:4
Aspect Ratio of output
screen 1.88Aspect Ratio of output
screen 2.35:1Aspect Ratio of output
screen Letter BoxAspect Ratio of output
screen NativeAspect Ratio of output
screen Unscaled
Aspect Ratio of output
screen 4:3
Aspect Ratio of output
screen 16:10
Aspect Ratio of output
screen 16:09Original
Aspect Ratio of output
screen 5:4
Aspect Ratio of output
screen 2.35:1Aspect Ratio of output
screen Letter Box Aspect Ratio of output
screen NativeAspect Ratio of output
screen Unscaled
Aspect Ratio of output
screen 4:3
Aspect Ratio of output
screen 16:10
Aspect Ratio of output
screen 1.88