Eiki Projector EIP-UJT100 User Manual

							11
AC Power Cord Requirement
The AC Power Cord supplied with this projector meets the requirement for use in the 
country you purchased it.  
AC Power Cord for the United States and Canada:
AC Power Cord used in the United States and Canada is listed by the Underwriters Laboratories (UL) 
and certified by the Canadian Standard Association (CSA).AC Power Cord has a grounding-type AC 
line  plug.  This  is  a  safety  feature  to  be  sure  that  the  plug  will  fit  into  the  power  outlet.  Do  not  try  to 
defeat this safety feature. Should you be unable to insert the plug into the outlet, contact your electri-
cian.
AC Power Cord for the United Kingdom:
This cord is already fitted with a moulded plug incorporating a fuse, the value of which is indicated on 
the pin face of the plug.  Should the fuse need to be replaced, an ASTA approved BS 1362 fuse must 
be used of the same rating, marked thus ASA. If the fuse cover is detachable, never use the plug 
with the cover omitted. If a replacement fuse cover is required, ensure it is of the same colour as that 
visible on the pin face of the plug (i.e. red or orange). Fuse covers are avai\
lable from the Parts De-
partment indicated in your User Instructions.If the plug supplied is not suitable for your socket outlet, 
it  should  be  cut  off  and  destroyed.The  end  of  the  flexible  cord  should  be  suitably  prepared  and  the 
correct plug fitted. 
WARNING : A PLUG WITH BARED FLEXIBLE CORD IS HAZARDOUS IF EN -
GAGED IN A LIVE SOCKET OUTLET.
The Wires in this mains lead are coloured in accordance with the followi\
ng code: 
    Green-and-yellow ......... Earth 
    Blue .............................. Neutral 
    Brown ........................... Live
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured 
markings identifying the terminals in your plug proceed as follows: The wire which is coloured green-
and-yellow must be connected to the terminal in the plug which is marked by the letter E or by the 
safety earth symbol  or coloured green or green-and-yellow. The wire which is coloured blue must 
be connected to the terminal which is marked with the letter N or coloured black. The wire which is   
coloured brown must be connected to the terminal which is marked with th\
e letter L or coloured red.
WARNING: THIS APPARATUS MUST BE EARTHED.
THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY   
ACCESSIBLE.  
						

							12
Standard Accessories
Owner's Manual (CD)AC Power cord
US Type*2   
Euro Type*1  
China Type*1 Remote control with batteries
 
 (AA or LR6)
EIP-UJT100
EIP-UJ T100+-+-
1
32
4 15
ASPECT
RATIOAUTO IMAGEPAUSE TEXT
MENUSHARPNPHASE
CONTRAST
POWER
INPUT
ON
OFF
BRIGHTNESS
ADDRESS
SWAP
PIP
FOCUSFOCUSZOOM
ZOOM
LENS CONTROL
Quick start guide RoHS Card for China QC Pass Card for China
Quick Start Guide •  Use this document as a start guide when setting up the
   projector.
•  For detailed information about installation, setup and 
   operation for projector, refer to the owner's manual on the 
   CD-ROM.
Accessories List
 Owners Manual (CD)EIP-UJT100EIP- UJT
1
00AC Power cordUS Type*2 / Euro Type*1 / China Type*1+-+-Remote control
Batteries (AA or LR6)132
4 15A
SPEC T
R ATIOA U TO  IMA GEPAU SE TE XT
M
EN USH ARP NPHAS E
C
O NTR ASTPO W ER
IN PU T
O
N OFFBR IG HTN ESSAD DRE SS
S W AP
P IPF O CUSFO CUSZOO MZOOMLE NS  C O NTR O LQuick start guide
RoHS Card 
for China
铅（ Pb） 汞（Hg ）镉（Cd ）六价铬（Cr(VI) ）多溴联苯（ PBB） 多溴二苯醚（ PBDE）
光机引擎 (
铝或铝镁合金 )X
O O O O O
镜头 X
O O O O O
灯泡 X
XO O O O
点灯器 X
O O O O O
弹片( 快削磷铜) X
O O O O O
风扇组件 X
O O O O O
灯泡盖保护开关 O
O X O O O
温度开关 O
O X O O O
基板组件 X
O O O O O
缆线 ,线材 X
O O O O O
电源线 X
O O O O O
电源插座组件 X
O O O O O
金属件( 快削磷铜 ,铜钉等) X
O O O O O
遥控器 X
O O O O O产品中有毒有害物质或元素的名称及含量列表╳：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11363-2006标准规定的限量要求。
备注：鉴于欧盟与中国对于 RoHS的不同规定，本投影机产品符合欧盟RoHS 指令(电气、电子设备中限制使用某些有害物质指令 ),本
表中标有X 的所有部件均为欧盟ROHS 指令所允许例外的部件。依据中国政府针对“电子信息产品污染控制管理办法＂为控制和减少电子信息产品废弃后对环境造成的污染，促进生产和销售低污染电子信息产品，保护环境和人体健康，仅提供有关本产品可能含有有毒及有害物质如后：部件名称有毒有害物质或元素○：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T11363-2006标准规定的限量要求以下。QC Pass Card 
for ChinaWarranty Card
for ChinaWarranty Card for USAWired Remote
Cable
Press and hold the POWER button for 5 seconds on the side control or OFF button the remote control to turn off the 
projector.
132
1ASPECT
RATIOAUTO IMAGE
HDBaseT
HDMI
RGBHV DVI
VGAPAUSE
TEXT
MENUSHARPNESSPHASE
CONTRASTPOWER
INPUT
ON
OFFBRIGHTNESSADDRESS
SWAP
PIPFOCUSFOCUSZOOMZOOMLENS CONTROL4532
1ASPECT
RATIOHDBaseT
HDMI
RGBHV DVI
VGAMENU
POWER
INPUT
ON
OFFFOCUSFOCUSZOOMZOOMLENS CONTROL45
Turn on the projectorTurn off the projector1. Connect the necessary signal cable.
2. Select the correct voltage 115V or 230V.
3. Connect the AC Power Cord. 4. Secure the power plug by 
    locking the plug holder clamp. 
5. Turn on the AC Power Switch.
6. Push the power button to turn 
    on the projector.AC IN
MAIN POWER
VOLTAGE SELECTHDMI IN VGA ING/YB/Pb R/Pr DVI-D IN
H V
RS-232C
HDBaseT1 2R/C IN
12V Trigger OUT
YPb Pr INOUT
SYNC
LANINOUT
3G-SDI1
2 5
3
432
1ASPECT
RATIOAUTO IMAGE
HDBaseT
HDMI
RGBHV DVI
VGAMENU
POWER
INPUT
ON
OFFFOCUSFOCUSZOOMZOOMLENS CONTROL456ENTER
INPUT
ERROR
MENU
ON
STANDBY>>>>LEDSTATUS6ENTER INPUT
ERROR
MENU
ON
STANDBY>>>>LED
STATUS5 sec.
How to install lens1. Remove the lens hole sponge 
    from projector.
2. Remove the lens cap (front and back)
    on the lens.
  132
EIP-UJT100EIP-UJT100XDo not look into the lens
while the projector is turned on. 
3. Insert the lens into lens holder so that the lens motor lead connecto\
r is 
    attached to the socket on the right side of the lens mount.
4. Slowly make the lever a half turn counterclockwise to lock the lens.
    Make sure that the lens is fully inserted to the projector.
4
Quick Start Guide •  Use this document as a start guide when setting up the
   projector.
•  For detailed information about installation, setup and 
   operation for projector, refer to the owner's manual on the 
   CD-ROM.Accessories List Owners Manual (CD)EIP-UJT100E I
P -U
J
T 1
0 0AC Power cordUS Type*2 / Euro Type*1 / China Type*1+-+-Remote control
Batteries (AA or LR6)132
4 15
A SPE
CT
R A
TIOA
UT
O I
M
AG E
P A
USE
TE
XT
M
E
N USHAR
PNPH AS E
C
O N
TR
AS TP
OW ER
I NP U
T
ON
O
FF
B R
IGHT N
ES S
A D
D R
ES S
S
W A
P
P
IPF O
C
USFO C
USZ
O O
MZO
OMLE
N S
 C
O N
TR OLQuick start guide
RoHS Card 
for China铅（ Pb） 汞（ Hg） 镉（ Cd） 六价铬（ Cr(VI)
） 多溴联苯（ PBB） 多溴二苯醚（ PBDE）
光机引擎 (铝或铝镁合金 )X
O O O O O
镜头 X
O O O O O
灯泡 X
XO O O O
点灯器 X
O O O O O
弹片 (快削磷铜 ) X
O O O O O
风扇组件 X
O O O O O
灯泡盖保护开关 O
O X O O O
温度开关 O
O X O O O
基板组件 X
O O O O O
缆线 ,线材 X
O O O O O
电源线 X
O O O O O
电源插座组件 X
O O O O O
金属件 (快削磷铜 ,铜钉等 ) X
O O O O O
遥控器 X
O O O O O产品中有毒有害物质或元素的名称及含量列表╳：表示该有毒有害物 质至少在该部件的某一均质材料中的含量超 出
SJ/T11363-2006 标准规定的限量要求。
备注：鉴于欧盟与中国 对于
RoHS 的不同规定，本投影 机产品符合欧盟 RoHS指令(电气、电子设备中限制使用某些有害 物质指令
), 本
表中标有 X的所有部件均为欧盟 RO HS指令所允许例外的部件。
依据中国政府针对“
电子信息产品污染控制管理办法＂为控制和减少电子信息产品废弃后对环境造成的污染，促进生产和销售低污染电子信息产品，保护环境和人体健康，仅提供有关本产品可能含有有毒及有害物质如后：部件名称有毒有害物质或元素○：表示该有毒有害物 质在该部件所有均质材料中的含量均在 SJ/T11363-2006标准规定的限量要求以 下。QC Pass Card 
for ChinaWarranty Card
for ChinaWarranty Card for USAWired Remote
CablePress and hold the POWER button for 5 seconds on the side control or OFF button the remote control to turn off the 
projector.132
1ASPECT
RATIOAUTO IMAGE
HDBaseT
HDMI
RGBHV DVI
VGAPAUSE
TEXT
MENUSHARPNESSPHASE
CONTRASTPOWER
INPUT
ON
OFFBRIGHTNESSADDRESS
SWAP
PIPFOCUSFOCUSZOOMZOOMLENS CONTROL45132
1ASPECT
RATIOAUTO IMAGE
HDBaseT
HDMI
RGBHV DVI
VGAPAUSE
TEXT
MENUSHARPNESSPHASE
CONTRASTPOWER
INPUT
ON
OFFBRIGHTNESSADDRESS
SWAP
PIPFOCUSFOCUSZOOMZOOMLENS CONTROL45Turn on the projectorTurn off the projector1. Connect the necessary signal cable.
2. Select the correct voltage 115V or 230V.
3. Connect the AC Power Cord. 4. Secure the power plug by 
    locking the plug holder clamp. 
5. Turn on the AC Power Switch.
6. Push the power button to turn 
    on the projector.AC IN
MAIN POWER
VOLTAGE SELECT HDMI IN
VGA ING/YB/Pb R/Pr DVI-D IN
H V
RS-232C
HDBaseT
12R/C IN
12V Trigger OUT
YPb Pr INOUT
SYNC
LANINOUT
3G-SDI1
2 5
3
4132
1ASPECT
RATIOAUTO IMAGEHDBaseT
HDMI
RGBHV DVI
VGAPAUSE
TEXT
MENUSHARPNESSPHASE
CONTRASTPOWER
INPUT
ON
OFFBRIGHTNESSADDRESS
SWAP
PIPFOCUSFOCUSZOOMZOOMLENS CONTROL456ENTER
INPUT
ERROR
MENU
ON
STANDBY>>>>LED
S TAT U S6ENTERINPUTERROR MENU
ON
STANDBY>>>>LED
S TAT U S5 sec.How to install lens1. Remove the lens hole sponge 
    from projector.
2. Remove the lens cap (front and back)
    on the lens.  132EIP-UJT100E IP -U JT 100XDo not look into the lens
while the projector is turned on. Quick Start Guide Accessories ListTurn on the projectorTurn off the projectorHow to install lensEIP-UJT1003. Insert the lens into lens holder so that the lens motor lead connector is 
    attached to the socket on the right side of the lens mount.
4. Slowly make the lever a half turn counterclockwise to lock the lens.
    Make sure that the lens is fully inserted to the projector.4铅（ Pb） 汞（Hg ）镉（Cd） 六价铬（Cr(VI) ）多溴联苯（PBB ）多溴二苯醚（PBDE ）
光机引擎( 铝或铝镁合金) X
O O O O O
镜头 X
O O O O O
灯泡 X
XO O O O
点灯器 X
O O O O O
弹片( 快削磷铜) X
O O O O O
风扇组件 X
O O O O O
灯泡盖保护开关 O
O X O O O
温度开关 O
O X O O O
基板组件 X
O O O O O
缆线 ,线材 X
O O O O O
电源线 X
O O O O O
电源插座组件 X
O O O O O
金属件( 快削磷铜,铜钉等) X
O O O O O
遥控器 X
O O O O O
产品中有毒有害物质或元素的名称及含量列表
╳：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11363-2006标准规定的限量要求。
备注：鉴于欧盟与中国对于RoHS 的不同规定，本投影机产品符合欧盟 RoHS指令(电气、电子设备中限制使用某些有害物质指令), 本
表中标有X 的所有部件均为欧盟ROHS 指令所允许例外的部件。
依据中国政府针对“电子信息产品污染控制管理办法＂为控制和减少电子信息产品废弃后对环境造成的污染，促进生产和销售低污染电子信息产品，保护环境和人体健康，仅提供有关本产品可能含有有毒及有害物质如后：部件名称有毒有害物质或元素
○：表示该有毒有害物质在该部件所有均质材料中的含量均在SJ/T11363-2006 标准规定的限量要求以下。
Warranty Card for ChinaWarranty Card for USA Wired Remote Cable                    
						

							13
Optional Accessories
Optional Lenses and Projection Size
Six types of motor-powered projection lens can be an option for EIP-UJT100, the projec-
tion lenses can cover the throw ratio range from 0.67:1 to 6.96:1.
Complete projection lens series as below table
Lens Type Zoom 
Ratio F#Focus Length
 
f (mm) Lens Shift Range
Throw Ratio
Vertical Horizontal
AH-D22010 FixF/2.5 in center, F/4.5 in corner 14.60%0%0.67:1
AH-D22020 FixF/2.5 in center, F/4.5 in corner 23.55-25% ~ +50% 0%1.12:1
AH-D22030 1.34F/2.5 in center, F/4.5 in corner 28.94 – 38.95-25% ~ +50% ±5%1.39~1.87 : 1
AH-D21010 1.37F/2.5 in center, F/4.5 in corner 39.0 – 53.43-25% ~ +50% ±10%1.87~2.56 : 1
AH-D23010 1.62F/2.5 in center, F/4.5 in corner 52.4 – 85.3-25% ~ +50% ±10%2.56~4.16:1
AH-D23020 1.67F/2.5 in center, F/4.5 in corner 84.86 – 142.03-25% ~ +50% ±10%4.16~6.96:1
Projection Size and Distance
Distance unit : m
Lens Type AH-D22010 AH-D22020 AH-D22030 AH-D21010AH-D23010AH-D23020
Inch Fixed FixedWideTeleWide TeleWide TeleWide Tele
80" 1.2 ---------
90" 1.3 ---------
100" 1.4 ---4.0 5.5 ----
120" 1.7 ---4.8 6.6 ----
150" 2.2 3.64.56.06.08.3 --13.4 22.5
200" 2.9 4.86.08.18.111.0 11.017.9 17.930.0
250" -6.07.510.1 10.113.813.822.422.437.5
300" -7.29.012.1 12.116.516.526.926.945.0
350" -8.410.514.114.119.319.331.431.452.5
400" -9.612.016.116.122.122.135.835.860.0
450” -10.913.518.118.1 -24.8 40.340.367.5
500" -12.115.020.1 --27.6 44.844.875.0
 Note:
The values in the tables are approximate and may be slightly different from the actual measurements.  
						

							14
Over view
Projector contents
Part Names and Functions
1
2
34567
8
9
8
10
 Lens Release Trolley
  Infrared Remote Receiver(Front)
  Air Intake Vent
  Filter Cover
  AC Power Switch
  Terminals and Connectors
  Exhaust Vent
  Adjustable foot
  Power Cord Connector
  Lens (Optional)
456
1
7
7
23
 Infrared Remote Receiver(Rear)
  Exhaust Vent and Lamp Cover 1
  Exhaust Vent and Lamp Cover 2
  Control Panel
  Filter Cover
  Air Intake Vent
  Adjustable foot  
						

							15
Terminals and Connectors
HDMI INVGA ING/YB/Pb R/Pr DVI-D IN
H V
RS-232C
HDBaseT
1 2R/C IN
12V Trigger OUT
YPb Pr INOUT
SYNC
LAN
INOUT
3G-SDI
 
■ HDBaseT  
It can support Full HD uncompressed video transmit from image device com\
patible with 
HDBaseT. Only supports video format over network cable. Data and sound are not \
sup -
ported.
 
■ RS-232  
Connect a RS-232(Not supplied) from the computer to the terminal for  \
controlling the 
projector.
 
■ 12V TRIGGER Out 1 and 2  
The TRIGGER terminal provides 12V (+/-1.5) output for screen control
 
■ R/C IN 
Connect the wired remote control to this jack with a remote control cabl\
e (supplied).
 
■ Y/Pb/Pr 
Standard and high definition (480i/480p/576i/576p/720p/1080i/1080p) component input, 
connects to DVD/HD-DVD/BD player, HD set-top-box or other SD/HD input source.
 
■ SYNC IN / OUT  
IN->From source equipment for informing which field of signal is the Left-eye or Right-
eye signal.  
OUT->From projector and be connected to the 3D SYNC wireless transmitter fo\
r syn -
chronizing the projected picture with the 3D glasses.
 
■ LAN (10/100 BASE-T)  
Connect the Ethernet cable to the terminals for controlling the projecto\
r. 
 
■ 3G-SDI IN / OUT  
Input SDI signals to IN and outputs the SDI signals from OUT.
 
■ HDMI IN  
Connect the HDMI signal from the video device to this terminal.
 
■ VGA IN 
Connect a computer output (Analog D-sub 15-pin type) to this terminal.\
 
■ 5 BNC IN (G/Y, B/Pb, R/Pr, H and V)  
Connect the VGA signals or Y/Pb/Pr signals.
 
■ DVI-D IN (Dual Link)  
Connect the DVI-D output on the computer to the terminal, the terminal c\
an support to 
HDCP compatible signal.
Note:
Not supported PIP, Warp, and Edge Blend. Can be connected LAN only.  
						

							16
Control Keys and LED Indicators
Control Keys
ENTERINPUT
ERROR
MENU
ON
STANDBY
>
>
>
>
LED
STATUS
 
■  (POWER)  
Turn on/off the projector (Press few seconds to 
off the projector).
 
■ INPUT   
Select the input source, press the button once to 
select next source option, the sequence of the 
source is HDBaseT, HDMI, DVI-D, VGA, Y/Pb/Pr, 
5 BNC, 3G-SDI.
 
■ MENU  
Press the button to open or close the OSD menu.
 
■ ARROW BUTTONS ( 
    ) 
Use the four buttons to move the cursor on OSD, 
select the item or adjust the setting
 
■ ENTER  
Use the button to confirm the changes you made 
and to show ZOOM/FOCUS OSD. When you 
press the button again, LENS SHIFT OSD  
appears.
 
■ STANDBY (LED-Blue)  
The indicator that shows the projector’s standby status.
 
■ ON (LED-Green)  
Displays the projector’s power status.
 
■ ERROR (LED-Red)  
Displays the cause of problem (i.e. temperature, fan, lamp or system) \
that has led to 
projector malfunction.   
LED Indicators
Standby
Cooling / Warm up
Lamp fail
Lamp door open Fan Fail
Over Temperature System ErrowLight on - Blue
Power on / Normal Light on - Green
Light on - Red Light flash - Green
Light flash - Red
Light flash twice - Red,
Light flash 3times - Red
Light flash 4times - Red
Time for lamps replacement Light flash - Green and Blue
Standby
ON
ERROR
Remark:
The time period of each step in the above LED blinking pattern is 0.5 second, e.g., for “Cooling / 
Warm up” state, the green LED will ON for 0.5 second, and then OFF 0.5 second, and then repeat the 
above LED pattern  
						

							17
Remote Control
1
32
1
ASPECT
RATIO
AUTO IMAGE
HDBaseT
HDMI
RGBHV DVI
VGA
PAUSE
TEXT
MENU
SHARPNESS
PHASE
CONTRAST
POWER
INPUT
ON
OFF
BRIGHTNESS
ADDRESS
SWAP
PIP
FOCUSFOCUS
ZOOM
ZOOM
LENS CONTROL
45
3
4
6
10
12
15
17
19
1
8
13
7
9
11
16 18
5
2
14
1.  ON 
Press a few seconds to power on the projec -
tor.
2.  OFF  
Press a few seconds to off the projector
3.  1,2,3,4  and 5 
Hotkeys for different picture source. Factory 
default setting is below. The settings of hot-
keys are changeable. Refer to  Page 54 
Button 1~5 
1 = HDMI 
2 = HDBaseT  
3 = VGA  
4 = RGBHV, Y/Pb/Pr 
5 = DVI (3D DVI)
Note: DVI(3D DVI), Refer to  page 37.
4.     
Use these buttons to make your selection or 
configure, adjust configuration or toggle be -
tween picture displays. 
5.  ENTER 
*Confirm the OSD change.  
*Press 1 time directly  
  -> show Zoom/Focus OSD. 
*Press 2 times directly     -> show Lens shift OSD.
6.  MENU 
Open and close the OSD menu.
7.  ASPECT RATIO  
Select the aspect ratio settings.
8.  TEXT 
When TEXT is set to ON, the user will be 
able to operate the OSD Menu normally. 
When TEXT is set to OFF, only ON, OFF, 1~5, 
SWAP, PIP, PAUSE will function normally; 
pressing any other buttons will not access 
the OSD Menu.
9.  AUTO IMAGE  
Resync the picture. (The adjustments also 
apply to PIP input). 
10.  PAUSE (SHUTTER) 
Open/Close the shutter.
11.  SHARPNESS  
Adjust picture sharpness and clarity.
12.  CONTRAST 
Adjust the picture contrast. 
13.  BRIGHTNESS 
Adjust the picture brightness.
14.  --- 
This function not available for this model. 
15.  PHASE 
When the picture flickers, doubles, distorts 
or appears to be wavy, press this button to 
adjust. 
16.  ---  
This function not available for this model. 
17.  PIP 
Use this button to display or disable PIP. 
18.  ADDRESS  
*Only 2 addresses are possible*   
Press and hold the ENTER button and press 
Address button until the remote control panel 
flashes once (approximately 5 seconds) to 
change the receiving address of the remote 
control. If you use one remote control to op -
erate two different projectors, you can assign 
different address for the two projectors so 
that when you operate projector A, projector 
B will not be affected. 
19.  SWAP  
Use this button to switch the sources of pic -
ture PIP display.  
						

							18
Note:
*In most situations, you can simply point the remote control at the screen which will reflect the IR sig-
nal from the remote back toward the IR receiver on the projector. In some cases, however, ambient 
light may prevent this. If so, try again.
*If the effective range of the remote control decreases, or it stops working, replace the batteries with 
new ones.
*The remote control may fail to operate if the infrared remote sensor is exposed to bright sunlight or 
fluorescent lighting.
Remote Control Battery Installation
    
12
3
1. Slide the battery cover to remove it.
2.  Install two AA(2) batteries with the correct polarity.
3.  Put back the cover.
Note:
*Make sure that the battery polarities are correct when installing the b\
atteries.
*Do not mix an old battery with a new one or different types of batteries.
*Avoid contact with water or liquid.
*Do not expose the remote control to moisture or heat.
*Do not drop the remote control.
*If you will not use the remote control for a long time, remove the batt\
eries to avoid damage from bat-
tery leakage. Please wipe the remote control clean and install new batte\
ries if the battery is leaked.
*Dispose of used batteries according to the instructions or your local d\
isposal rule or guideline.  
						

							19
Remote Control Receivers and Operation Range
Infrared Remote Receivers are provided on the front and rear cover. Point the remote 
control toward the projector, then press the buttons. Maximum operating range for the re-
mote control is about 12 meters and ±30 degrees.
12m
±30°
12m
±30°
Note:
When hanging the projector from the ceiling, point toward the Infrared Remote Receiver which is lo-
cated farther away from the fluorescent light. 
Wired Remote Control
The remote control can be used as a wired remote control. Wired remote control helps 
you use the remote control outside the operating range. Connect the remo\
te control and 
the projector with the remote control cable (supplied). If the remote control is connected to 
the cable, the remote control does not emit signal.
HDMI IN VGA ING/YB/Pb R/PrH
RS-232CHDBaseT12R/C IN
12V Trigger OUT
YPb
IN OUT
3G-SDI
Wired Remote cable length = 5m(16.4 feet)  
						

							20
Installation
Lens Installation
Before setting up the projector, install Projection Lens on the projector.
Before installation, check where the projector is used and prepare a suitable lens. For 
the details,  contact the sales dealer where you purchased the projector\
.
Install and change the projector Lens:
1.  Remove the sponge.
2. Insert the lens and ensure the lens touches the lens holder. Carefully the lens motor 
board must insert into the machine's jack.