Eiki Projector EIP-UJT100 User Manual

61
3. 
Insert the new filters into the machine.  
Black side Black side
White side
xWhite side
x
3243411700
3243270701
4. 
Tighten the screws on the filter cover. 
ORDER REPLACEMENT Filter
Replacement filter can be ordered through your dealer. 
When ordering a filter, give following information to the dealer.
Replacement Filter P/N: 3243270701(Rear), 3243411700(Front)  

62
Appendix
Technical Specification
ModelEIP-UJT100
Display Type DLP
Native Resolution WUXGA (1920 x 1200)
Maximum Resolution WUXGA (1920 x 1200)@60Hz
Lamp Life and Type 2000hours(Normal 465W), 2500hours(ECO 360W)
Aspect Ratio Native, Unscaled, 5:4, 4:3, 16:10, 16:9, 1.88, 2.35 and Letterbox
Lens Shift Range V(-25%~50%), H(+/-10%)
Keystone Correction Vertical: +/-20° Horizontal:+/-35°
Synchronization Vertical: 23.98 - 120 Hz
Horizontal: 15.63 - 91.15kHz
Edge Blending Yes (built-in)
Video Compatibility...

63
Product Outline Dimension
270
499.8
220
105
160
633.4
Mounting bracket screw hole (M6)
These screw holes are used to mount the 
projector to its designated mounting bracket 
using 6 M6x15 screws. The dimensions of the 
screw holes are shown in the picture below.
EIP-UJT100  

64
Support Timing List
Signal FormatResolutionFrame 
Rate 3 RCA
5BNC
HD15- 
RGBHV HD15
 
YUV HDMI
SDI
Y-Pr-Pb Y-Pr-Pb RGBYUV
YUVYUV
8 bit 10 bit 12 bit
PC 640x480
59.94 VV V
640x480 74.99 VV V
640x480 85 VV V
800x600 60.32 VV V
800x600 75 VV V
800x600 85.08 VV V
848x480 47.95 VV V
848x480 59.94 VV V
1024x768 60 VV V
1024x768 75 VV V
1024x768 85 VV V
1280x720 47.95 VV V
1280x1024 60.02 VV V
1280x1024 75.02 VV V
1280x1024 85.02 VV V
1600x1200 60 VV V
1920x1080 47.95 VV V
1680x1050 59.94 VV V
1920x1200 50...

65
SDI Format
TimingSDI Link modeSignal Standards Color
Encode Sampling
Structure Bit Depth
NTSC SDSMPTE 259M-C 270Mb
ps SDYCbCr4:2:210
PAL SDSMPTE 259M-C 270Mb
ps SDYCbCr4:2:210
1035i60 HDSMPTE 292M 1.5Gb
ps HDYCbCr4:2:2 10
1080i59 HDSMPTE 292M 1.5Gb
ps HDYCbCr4:2:2 10
1080i60 HDSMPTE 292M 1.5Gb
ps HDYCbCr4:2:2 10
1080P30 HDSMPTE 292M 1.5Gb
ps HDYCbCr4:2:2 10
1080P25 HDSMPTE 292M 1.5Gb
ps HDYCbCr4:2:2 10
1080i50 HDSMPTE 292M 1.5Gb
ps HDYCbCr4:2:2 10
1080P24 HDSMPTE 292M 1.5Gb
ps HDYCbCr4:2:2 10
720P60...

66
Projector Control via LAN
The projector supports to control the projector through the network. Before using this 
function, please set up the network configuration of your personal computer .
1.  Set up network configuration.  
The default IP address of the projector is 192.168.0.100, please follow below steps to\
 
set the network configuration.  
Connect RJ-45 cable from PC to the LAN connector on the projector. 
HDMI IN VGA ING/YB/Pb R/Pr DVI-D IN
H V
RS-232C
1
2R/C IN
12V Trigger OUT
YPb Pr INOUT...

67
Open a web browser on your PC and type the IP address of the projector      
  (192.168.0.100), IP configuration will be shown on the web page.
Set the IP address and subnet mask and click SAVE to confirm the configuration. Projec-
tor Web Control will show below message for confirmation.
“The projector IP will be changed and the connection to the projector will be lost, do you 
want to continue ?
Select "Yes" to confirm the changes, "No" to cancel.Note: 
Make sure the IP address of...

68
Using Projector Web Control
 
■ Source/General  
Use this page to control the general settings of the projector such as p\
ower on/off, 
source….etc. 
Note:
If projector control option is selected to RS232, the web control will be interrupt. Network control has 
to be enabled from the projector’s OSD menu before connecting to projector web control.
 
■ Image Setting  
Click arrows to adjust the image settings such as Brightness, Sharpness…\
etc. on the 
web page.  

69
 
■ Lens Adjustments  
This page allows you to adjust Zoom, Focus and Lens shift. The operation is similar to 
control the projector by the remote control or control panel on the proj\
ector, click arrows  
to adjust the settings. 
 
■ Geometry Adjust  
Click the arrow buttons to adjust Blanking, Warp, Four Corner, and click the option 
to select the aspect ratio setting. Click Reset option to reset Blanking\
 or Warp to the 
default setting.   

70
 
■ Edge Blend  
Click Status option to enable or disable Edge Blend function. When Edge \
Blend is 
disabled, the other options are unavailable and N/A is shown on the column. The other 
options are available only when Edge Blend is enabled.  
 
■ Advance Control  
This page allows you to select color temperature or adjust black balance\
 or white 
balance. Click the option to select Color Temp. or arrow button to adjust the setting.