Eiki Projector EIP-UJT100 User Manual

31
Selecting an Input Source
When you turn on the projector, it switches to the last selected input and waits for a val-
id signal. Press the “INPUT” on the remote control or control pane\
l to switch to an input 
source directly.  Refer to  page 17 button 1-5 for default input setting and these setting 
are changeable, Refer to  Page 54 Button 1~5
ENTER
INPUT
STANDBY
>
>
>32
1
HDBaseT
HDMI
RGBHV DVI
VGA
POWER
INPUT
ON
OFF
FOCUSFOCUS
ZOOMLENS CONTROL
45
Selecting a Aspect Ratio
Press ASPECT to adjust the...

32
How to Operate the OSD Menu
The projector has an On-Screen Display (OSD) that allows you to adjust the image and 
change settings.
OSD Operation
Following steps are a basic way for operating the OSD.
1.  Press the MENU button to open the OSD.
2.  Press ▲ or ▼ to select a title menu.
3.  Press ◄ or ► to select an item.  
The selected item will be highlighted.
4.  Press the Enter, and ▲ or ▼ to change or adjust the selected item.
5.  Press the MENU in the monent move to upper menu.  
ERRORMENU
ON
>
>
>...

33
Changing the OSD Language
The product can display the menus in English, French, Spanish, German, Portuguese, 
Simplify Chinese, Traditional Chinese, Japanese or Korean. 
Press the “MENU” to open the OSD. Go to SYSTEM and select Language then press 
the Enter. You can select a language there.  

34
OSD Tree
Main MenuSub-menu
MAIN Input Selection
HDMI
HDBaseT
VGA
Y/Pb/Pr
RGBHV, Y/Pb/Pr
3G-SDI
3D DVI
Color Space Auto
REC709
REC601
RGB-PC
RGB-Video
Input Locking Auto
48Hz
50Hz
60Hz
Auto Power Off On
Off
Auto Power On On
Off
No Signal Logo
Blue
Black
White
Auto  Image Adjust Off
Auto
AlwaysMain MenuSub-menu
PICTURE Contrast
0-200
Brightness 0-200
Sharpness 0-200
Noise Reduction 0-200
Color Temperature 3200K
5400K
6500K
9300K
Native
Input Balance Black Balance Offset
  Red Offset
  Green Offset...

35
Main MenuSub-menu
LAMPS Power
ECO
Normal
Custom Level
Mode Single
Dual
High Altitude On
Off
Custom Power Level 78.3%~100%
Lamp1 Status On / Off
Lamp2 Status On / Off
Lamp1 Run Time XX HRS
Lamp2 Run Time XX HRS
ADVANCED Rear Projection
On
Off
Ceiling Mode On
Off
Lens Control Zoom / Focus
Shift H/V
Dynamic Contrast On
Off
Gamma 1.8
2.0
2.2
2.35
2.5
DICOM SIM.
Test Pattern Color Bar
Cross hatch
Half scanning
Red 
Green
Blue
White
Black
Red
Green
Blue
Gray Scale
Color Gamut Native
EBU
SMPTE
CustomMain...

36
Main MenuSub-menu
SYSTEM IR Address
1
2
Eco Network Power On
Off
Network Network Status
  IP Address
  Subnet Mask
  Gateway
  DHCP
Network Setting
  IP Address
  Subnet Mask
  Gateway
  DHCP
Menu Position Top Left
Top Right
Bottom Left
Bottom Right
Center
Start Up Logo On
Off
Start Up Chime On
Off
Button 1 HDMI
HDBaseT
VGA
Y/Pb/Pr
RGBHV, Y/Pb/Pr
3G-SDI
3D DVI
Button 2 HDMI
HDBaseT
VGA
Y/Pb/Pr
RGBHV, Y/Pb/Pr
3G-SDI
3D DVI
Button 3 HDMI
HDBaseT
VGA
Y/Pb/Pr
RGBHV, Y/Pb/Pr
3G-SDI
3D DVI
Button 4 HDMI...

37
OSD Operation-MAIN
Input Selection
You can select an input source. 
 
■ HDMI:  HDMI input.
 
■ HDBaseT:  HDBaseT input.
 
■ VGA:  Analog RGB.
 
■ Y/Pb/Pr:  YPbPr input.
 
■ RGBHV, Y/Pb/Pr:  Analog RGB / Component.
 
■ 3G-SDI:  Uncompressed digital video from a serial connection (coaxial)
 
■ DVI-D (3D DVI):  Use this DVI dual link to connect to a stereo 3D source – it is usua\
lly a 
computer with 3D Graphics card, and 3D applications.
Below information is the DVI-D (3D DVI) format:
Signal Type...

38
Color Space
This function allows you to change component and VGA input sources. You can select 
different color space for different color performance. 
 
■  Auto:  The default setting is Auto. 
HDMI:  If the Auxiliary Video Information (AVI) contains color space and/or range data, 
the EIP-UJT100 uses that information to switch to corresponding color sp\
ace.   
RGB:  If Hsync or Vsync signals are present, the projector will switch to RGB\
-PC color 
space.   
Component:  For SDTV and EDTV...

39
Auto image Adjust
Set the timing of the Auto image Adjust function for(Resync on page 41) below 3 
modes:
 
■ Off:  Auto image function is not executed.
 
■ Auto:  Use the parameters that users used last time.  
The adjusted parameters are stored in the projector, 5 resolution data for each digital 
and analog inputs. If there is no record of parameters, auto image funct\
ion will be   
executed.
 
■ Always:  Auto image function is executed automatically when the input source is   
selected.
OSD...

40
Noise Reduction
Use◄  or  ►to  adjust  the  noise  of  the  projected  image.  This  function  is  suitable  for  the 
elimination of image noise from interleaving SD input. Generally speaking, reducing image 
noise will lower the value of high frequency detail and make the image appear more mel-
low. Adjustable value: 0 to 200.
Color Temperature
Use  ◄  or  ►  to  adjust  the  color  temperature  3200K,  5400K,  6500K,  9300K  or  Native  of 
the projected image.
This refers to the control of color...