Eiki Lc-Xs25 Multimedia Projector Owners Manual

51
Setting
On start
When  this  function  is  "On",  the  projector  is  automatically 
turned  on  just  by  connecting  the AC  power  cord  to  a  wall 
outlet.
Note:
    Be sure to turn the projector off properly (see "Turning  Off  the  Projector"  on  page  19).    If  the  projector  is 
turned  off  in  the  incorrect  sequence,  the  On  start 
function does not operate properly.
On start
Lamp control
T h i s  f u n c t i o n  a l l o w s  y o u  t o  c h a n g e  b r i g h t n...

52
Setting
Remote control
This projector provides two different remote control codes: 
the  factory-set  initial  code  (Code  1)  and  the    secondary 
code  (Code  2).    This  switching  function  prevents  remote 
control  interference  when  operating  several  projectors  or 
video equipment at the same time.
W h e n  o p e r a t i n g  t h e  p r o j e c t o r  i n  " C o d e  2 " ,  b o t h  t h e 
projector  and  the  remote  control  must  be  switched  to 
"Code 2".
To change...

53
Setting
Key lock
Security (Key lock and PIN code lock settings)
This  function  allows  you  to  use  Key  lock  and  PIN  code 
lock function to set the security for the projector operation.
This  function  locks  operation  of  the  top  control  or  the 
remote control.
It  is  useful  to  prevent  operation  by  an  unauthorized 
person.. . . . . .   not locked.
. . . . . .   l o c k  t h e  o p e r a t i o n  o f  t h e  t o p c o n t r o l .    To  u n l o c k ,  u s e  t h e 
remote control.
....

54
Setting
To Enter the PIN code
Select  a  number  by  pressing  the  Point ▲▼  buttons.  And 
then  press  the  Point ►button  to  fix  the  number  and  move 
the  pointer.    The  number  changes  to  " ".    If  you  fixed 
an  incorrect  number,  move  the  pointer  to  the  number 
you  want  to  correct  by  pressing  the  Point 
◄  button,  and 
then  select  the  correct  number  by  pressing  the  Point ▲▼ 
buttons.
Repeat this step to complete entering a four-digit number. 
After...

55
SettingSetting
This  function  provides  the  following  alternatives  in  the 
cooling fans' operation after turning off the projector. (p.19)
 L1
. . . . . .  normal operation
  L2
. . . . . .  s
l o w e r  a n d  l o w e r - s o u n d  t h a n  t h e  n o r m a l 
operation  (L1),  but  it  takes  longer  to  cool  the 
projector down.
Fan
T h i s  f u n c t i o n  i s  u s e d  t o  r e s e t  t h e  l a m p  r e p l a c e m e n t 
counter.    When  replacing  the  projection  lamp,  reset...

56
Factory default
This  function  returns  all  setting  values  except  for  the  user 
logo,  PIN  code  lock,  Logo  PIN  code  lock,  and  the  lamp 
counter to the factory default settings.
Exit the Setting Menu.
Quit
Factory default
SettingMaintenance and Care
Select  Factory  default  and  this 
box appears. Select [Yes], and 
the next box appears.Select  [Yes]  to 
activate it.
Filter counter Filter counter
Use  the  Point  ◄►  buttons  to 
set  the  timer.  Select  from  (Off/
400H/700H/1000H)...

57
Maintenance and Care
Filter Instructions
Filter prevents dust from accumulating on the optical elements inside th\
e projector. Should the filter 
becomes clogged with dust particles, it will reduce cooling fans’ effectiveness and may result in internal heat 
buildup and adversely affect the life of the projector. This projector has an electrically operated filter which 
helps you to replace the filter easily. The projector monitors the condition of the filter at all time and repla\
ces 
a filter with...

58
Turn off the projector, and unplug the AC power cord from 
the AC outlet.
First, clean up the dust on the projector and around the air 
vents.
Loosen 2 screws of the filter cover with a screwdriver and 
open the filter cover.
Put  the  new  one  back  into  the  position  and  rotate  back 
the  handle.  Make  sure  that  the  filter  cartridge  is  properly 
and  fully  inserted.  Close  the  filter  cover  and  tighten  the  2 
screws back into position.
CAUTION
Make sure the filter cartridge is...

5
Maintenance and Care
Be sure to reset the Scroll counter after replacing the filter cartridge\
. 
Press  the  MENU  button  to  display  the  On-Screen 
Menu.  Use  the  Point ◄►  buttons  to  move  the  red 
frame pointer to the Setting Menu icon.
Use  the  Point  ▲▼  buttons  to  move  the  red  frame 
pointer to Filter counter and then press the SELECT 
button. A dialog box appears showing the Used time 
option  and  the  Scrolls  remaining  option.  Use  the 
Point ▲▼  buttons to select...

60
Maintenance and Care
Wh e n  th e  l i fe  o f  th e  p r o j e cti o n  l a m p  o f  th i s  p r o j e c to r 
draws  to  an  end,  the  Lamp  replacement  icon  appears  on 
the  screen  and  LAMP  REPLACE  indicator  lights  yellow. 
Replace  the  lamp  with  a  new  one  promptly.  The  timing 
w h e n  t h e  L A M P  R E P L A C E  i n d i c a t o r  s h o u l d  l i g h t  i s 
depending on the lamp mode.
Lamp Replacement
Top Control
For  continued  safety,  replace  with  a  lamp  of  the...