Eiki Lc-Xip2000 Multimedia Projector Owners Manual

Maintenance and Troubleshooting
4.Q: Why can’t install the program? 
A: You might need to log in as “administrator” to be able to install program to
your computer.    Consult with your I/T engineers to help you in this case.
In addition, pro
gram will be deleted if you install twice due to the setting of
program. In this case, please install again. 
5.
Q: Why is it showing “No lightpen found”? 
A: The possible reasons for this might be: 
(1).USB cable not well connected 
Please check and make sure the...

Maintenance and Troubleshooting
10.
Q: Why is the cursor not at the position pointed? 
A: The possible reasons for this are: 
(1).The system not been well calibrated. Try to point to the “center” of green
 
cross target when you running calibration. 
(2).The position o
f the projector, screen or projection size has been changed
(3).The image resolution been changed 
Run the calibration procedure again will solve the problem.
11.
Q: Why is the lightpen not working? 
A: The reasons for this are: 
(1).When...

Maintenance and Troubleshooting
Lamp Replacement
Lamp door  Lamp Screw
 
1. Remove the lamp screw from the lamp door. 
2. Remove the Lamp Door. 
3. Remove the two Phillips head screws that hold the lamp in place. 
4. Grasp the handle on the top of the lamp and pull the lamp straight up
 
out of the projector. 
5.  Slide the replacement lamp into place and press firmly to seat the lamp. 
6.  Reinstall the screws removed in step 3. 
7. Reinstall the lamp door correctly and tighten the screw on the lamp...

Maintenance and Troubleshooting
Indicators  
The Power and Lamp indicators show the status of the projector. Before
requesting repair, check the projector status using the chart below. I
f
the problem cannot be resolved contact your dealer. 
an internal fan, the lamp will shut off
73
 
Power 
(Green) 
 
Lamp 
(Red)  
Conditions 
 
Notes 
  
Slow 
flashing 
 
 
Off 
 
Stand by 
mode 
 
Projector is ready to be turned on (normal) 
 
 
On 
 
 
Off 
 
 
On mode 
 
 
Projector is on and operating normally...

Maintenance and Troubleshooting
Connect correctly.
Ad
just the volume.
Remove obstacle between
contrast settin
g.
Note
：Although bright spots or dark spot may appear on the screen ,this is a
unique characteristic of liquid crystal displays,and it does not constitute or imply
a machine defect. 
74 
 
Symptom 
 
Possible cause 
 
Remedy 
   
 
The power is 
not turned on 
 
The main power switch is not 
turned on. 
The power cord is 
disconnected. Turn on the main power 
switch. 
Plug the power cord into...

List of Support Displays Modes
XGA
75
 
List of Supported Monitor Displays 
Computer mode 
Signal Refresh Rate(Hz) Resolution(dots) 
VGA 60 640X480 
VESA 60/72/75/85 640X480 
SVGA 56/60/72/75/85 800X600 
60/70/75/85 1024X768 
SXGA 70/75 1152X864 
SXGA 60/75 1280X960 
SXGA 60 1280X1024 
MAC 67 640x480 
MAC 75 832x624 
MAC 75 1024x768 
MAC 75 1152x870 
Component(YPbPr) 
Signal Refresh Rate(Hz) Resolution(dots) 
SDTV(480i) 30  720X480 
SDTV(480p) 60  720X480 
HDTV(720p) 60  1280X720 
HDTV(1080i) 30...

Configuration of Terminal 
Confi
gurations of Terminal   
76 S-Video signa 
Signal name Connection 
Y signal    GND 
return(GND) GND 
C signal    Y 
return(GND) C 
Y signal Input   
C signal Input   
Analog RGB 
Input/output 
12345
678910
1112131415 
Signal name Connection Signal name Connection 
R signal Input  R  N.C  N.C 
G signal Input  G  N.C  GND 
B signal Input  B Signal 
return(GND) N.C 
N.C N.C DDC_Data DDC/SDA 
GND GND HSYNC/TTL/co
mp.sync H 
R return(GND)  GND  VSYNC  V 
G return(GND)  GND...

U.S.A. 
EIKI International, Inc. 
30251 Esperanza 
Rancho Santa Margarita 
CA 92688-2132 
U.S.A. 
Tel : 800-242-3454 (949)-457-0200 
Fax :  800-457-3454 (949)-457-7878 
E-Mail : [email protected] 
 
Deutschland & Österreich 
EIKI Deutschland GmbH 
Am Frauwald 12 
65510 Idstein 
Deutschland 
Tel : 06126-9371-0 
Fax :  06126-9371-14 
E-Mail : [email protected] 
 
 
China 
EIKI (Shanghai) Co.,LTD 
1. Dapu Road, Golden Magnolia Plaz
a
#2109 Shanghai, 
200023 China 
Tel : 86-21-5396-0088 
Fax :  86-21-5396-0318 
E-Mail...