Eiki Lc-Xip2000 Multimedia Projector Owners Manual

Part Names and Function:(continued)
Remote Control Batteries Installation
1. Remove the battery cover.
2. Loading the batteries. 
Make sure the plus and minus poles are
correctly oriented. 
3. Close the battery cover.
C A U T I O N
1. Avoid excessive heat and humidity. 
2. Do not drop the remote control. 
3. Do not expose the remote control to water or moisture, this could 
result in malfunction. 
4. When the remote control will not be used for an extended period,
 
remove the batteries. 
5. Replace the...

Installation
Setting Up the Projector
The projector supports the following four different projection methods 
Front projection
150
”
Rear
150
”
A special method of installation is required in order to suspend the 
projector from the ceiling. Please ask your dealer for details. 
21
 
  

Installation(contiuned)
Setting Up the Projector
Rear ceiling projection
150
”
Front ceiling projection
150
”
A special method of installation is required in order to suspend the 
projector from the ceiling. Please ask your dealer for details. 
22 
     

Installation(contiuned)
Size and Projection Distance  
The distance between the projector and screen determines the 
actual image size. Refer to the table below to determine the image 
size at a given distance. 
A:B Ratio=6.5:1 
A
B
23
Screen Size (inches) 
(WxH) mm   5 0”
 6 0 ”
 
1 0 1 6 x 7 6 2   1 2 1 9 x 9 1 4 
Zoom(min)   3 . 8 ’ ( 1 . 2 m )  4 . 6 ’ ( 1 . 4 m ) 
 
Zoom(max)  
 
3 . 3 ’ ( 1 . 0 m )  3 . 8 ’ ( 1 . 2 m ) 
 
Screen Size(inches) 
(WxH) mm  8 0 ” 1 0 0 ”
 
1 6 2 6 x 1 2 1 9  2 0 3 2 x...

Installation(contiuned)
Adjusting the Image Position 
 
Use the adjustable foot at the front of  the projector to set the image
height.
 Rotate the adjustable foot at the rear of the projector to fine-
tune
 the image position. 
When the foot is adjusted, it may cause the shape of the projected
image
 to become distorted. Use the keystone correction function to
correct
 this distortion. 
To retract the front adjustable foot, press the foot adjust button. The 
front
 adjustable foot will slowly retract...

Installation(contiuned)
Moving the projector 
 
1. Use the carry bag when moving the projector.(option) 
2. Replace the lens cover and retract the front adjustable foot when 
moving the projector to prevent damage to the projector. 
carry bag 
( O p t i o n a l ,    p l e a s e    c o n t a c t    y o u r    d e a l e r    f o r    m o r e    i n f o r m a t i o n )
C A U T I O N  
The optional carry bag is intended to protect the projector
from dust and scratches on the surface of the cabinet. It is...

Installation(contiuned)
Software and Hardware install 
 
1.Section one : System Requirements
2.Section two : Software and Hardware driver installation
Step 1: Insert the Disc to the PC. 
Step 2: Execute setup.exe 
Step 3: Next 
26 System Requirements 
OS Required  Microsoft Windows 2000/XP(SP2)
 
Processor Type Intel Pentium IV or above 
RAM 256 MB or above 
Min. Free disk space 30 MB 
CD-ROM Driver & available USB 2.0 port  

Installation(contiuned)
Software and Hardware install 
 
2.Section two : Software and Hardware driver installation
Step 4: Install 
27 

Installation(contiuned)
Software and Hardware install 
 
2.Section two : Software and Hardware driver installation
Step 5: Finish (“LightPen” software installation) 
28  

Installation(contiuned)
Software and Hardware install 
 
2.Section two : Software and Hardware driver installation 
Step 6: Next (Continue to install driver for CMOS hardware)
29