Eiki Lc-Xdp3500 Multimedia Projector Owners Manual

28
MENU
Presentation Menu
Step:
1.	Use	the	▲	/▼buttons	
to select an item.
2.	Use	the	◄	/	►	buttons	
to select an item or 
adjust the value.
ItemSelectionDescription
AUTO CEILINGOFF / ON
Automatically invert the image when the projector is turned 
upside down, i.e. when the projector is mounted on the 
ceiling.
FRONTEXECUTENormal projection mode.
CEILINGEXECUTEMirror the image vertically, only for the projector mounted 
upside down.
REAREXECUTEMirror the image horizontally, only for projecting onto rear...

29
MENU
NOTE
►		The	replacement	warning	message	is	set	to	appear	after	about	2000	hours	of	lamp	use	in	order	
to maintain the initial brightness. When replacement message appears, replace the lamp with a 
new one as soon as possible, even if the lamp is still workable..
Presentation Menu
Reset Lamp Timer
The lamp timer is the time counted after the last resetting. The usage time of the lamp 
is	shown	in	the	PRESENTATION	Menu.	Pressing	the	RESET 	button	or	the	►	button	
displays a dialog.
To	reset	the...

30
MENU
Security Menu
Step:
1.	Use	the	▲	/▼buttons	to	
select an item.
2.	Use	the	◄	/	►	buttons	
to select an item or 
adjust the value.
ItemSelectionDescription
PIN LOCK 
PROTECTION
OFF
ON 1
ON 2
OFF: Turn off PIN lock protection.
ON	1:		 PIN	code	is	needed	only	at	the	first	time	after	 AC	
power has been switched on.
ON 2:  PIN code is needed every time while the projector is 
turned on.
 CAUTION:
Once the PIN code had been set, the projector cannot be 
used unless you enter the correct PIN code....

31
MENU
Security Menu
Step:
1.	Use	the	▲	/▼buttons	to	
select an item.
2.	Use	the	◄	/	►	buttons	to	
select an item or adjust the 
value.
ItemSelectionDescription
FILTER TIMERShow	the	filter	use	time.
RESET FILTER
TIMEREXECUTEReset	the	filter	timer	after	cleaning	/	changing	filter.
FILTER COUNTER
500 hours
800 hours
1000 hours
Select (500 / 800 / 1000 hours) depending on the 
environment.(default : 500 hours). Please see next page.
MAC ADDR.
For LAN control module, "MAC ADDR." will be shown in...

32
MENU
NOTE
►	Please	reset	the	Filter	time	only	when	you	replace	the	filter.
Auto Filter Alert
Auto	Filter	Alert	in	SECURITY 	category	shows	the	air	filter	use	time	and	alerts	user	to	change	
filter.	When	the 	operating	time 	reaches	the	set	time,	a 	warning	message 	will	appear	on	the	screen	to	
remind	user	of	filter	cleaning	/replacing.
Filter Replace...
Filter has been used for more than 500 hours. 

33
MENU
VO L - VO L+
M EN U
I N PU T
PIN Key In Operation
When the projector is turned on and the 
PIN LOCK PROTECTION is set to [ON], 
the image will show as on the right side.
1.   Press the MENU button on the projector 
or remote control. Enter PIN code by 
keypad or remote control.
2. How to enter a PIN code? 
You can use control panel or remote 
control.
CONTROL PANEL KEYSTONEREMOTE CONTROL
The control panel and remote control buttons to enter a sequence of PIN code is like the photo below.
(1)...

Network Control Software Application
34
Network Control Software Application
	 
Register the projector(s) which needs to be controlled. 
“ Auto search ” can help you to seek the projector(s) source easily. 
After registering in the work group, you can start to control the projec\
tor.
		Group the projector(s) into different sections. 
You can monitor the status easily by GROUP NAME function in the network.
		Monitor the status for each projector. 
a.You can manage and change the monitoring content by...

Before Use
35
Before Use 
Before Using Network Control Software
		If the system is Windows 2000, NT 4.0 or XP, the PC should be started by the 
Administrator.
		Before starting the Network Control software, please check the following\
.
(1) The computer is installed with Network Control software. 
(2)  
The projector is powered on and the LAN wire is well connected to the pr\
ojector.
(3)   Make sure the computer and projector can connect to network. Network Con\
trol 
software needs to arrange in...

36
Before Use
Projector Auto Search.
		Click the  (Projector search), located projector will show on the network 
correctly. (Graph2)
		Click  (search again), the projector which is well connected with a PC will be 
shown. (Graph3)
		Click  (register projector), the projector information will show on the monitor 
window. Click  button (exit), it will cancel the registered item then return to 
register table.
NOTE
When the security warning window appears while Network Control is execut\
ing, 
please...

37
Before Use 
Projector Auto Search.
		Projector Auto Search can rank group names or display names by clicking the 
monitor window title (Group Name) or (Projector Name). This will help you easily  
understand projectors status.
		After registering, you can click  button (Data single capture) in the tool bar or 
click  button (Start Auto Scan) to monitor the projector(s).
NOTE
When pressing   (About) button for help, you will see icons explained as in the chart\
.