Eiki Lc-Xbl30 Multimedia Projector Owners Manual

61
Maintenance and Cleaning
When	the	projection	lamp	of	the	projector	reaches	its	end	
of	life,	the	Lamp	replacement	icon	appears	on	the	screen	
and	LAMP	REPLACE	indicator	lights	yellow.	Replace	the	
lamp	with	a	new	one	promptly.	The	timing	when	the	LAMP	
REPLACE	indicator	should	light	is	depending	on	the	lamp	
mode.
Follow	these	steps	to	replace	the	lamp.
For	continued	safety,	replace	with	a	lamp	of	the	
same	type.	Do	not	drop	a	lamp	or	touch	a	glass	
bulb!	The	glass	can	shatter	and	may	cause...

62
Maintenance and Cleaning
This	projector	uses	a	high-pressure	lamp	which	must	be	handled	carefully	and	properly.		
Improper	handling	may	result	in	accidents,	injury,	or	create	a	fire	hazard.
●	Lamp	life	may	differ	from	lamp	to	lamp	and	according	to	the	environment	of	use.	There	is	no	guarantee	of	 the	 same	 life	 for	 each	 lamp.	 Some	 lamps	 may	 fail	 or	 terminate	 their	 life	 in	 a	 shorter	 period	 of	 time	
than	other	similar	lamps.
●	 If	 the	 projector	 indicates	 that	 the	 lamp	 should	 be...

63
  Problem:	–	Solutions
  No power	 –	Plug	the	power	cord	of	the	projector	into	the	AC	outlet.	
		 –	See	if	the	POWER	indicator	lights	red.	
		 –		Wait	until	the	POWER	indicator	stops	blinking	to	turn	on	the	projector	
again.	The	projector	can	be	turned	on	after	the	POWER	indicator	
turns	red.	See	page	18.
		 –	Check	the	WARNING	indicator.	If	the	WARNING	indicator	lights	red,																	
																																																																					projector	cannot	be	turned	on.	See	page...

64
Appendix
  No image	–	Check	the	connection	between	your	computer	or	video	equipment		
		 	 and	the	projector.	See	pages	14-16.	
		 –	See	if	the	input	signal	is	correctly	output	from	your	computer.	Some		
		 	 laptop	computers	may	need	to	change	the	setting	for	monitor	output		
		 			when	connecting	to	a	projector.	See	your	computer’s	instruction		
		 	 manual	for	the	setting.		
		 –	It	takes	about	30	seconds	to	display	an	image	after	turning	on	the		
		 	 projector.	See	page	18.
		 –		Check	the	Input...

65
Appendix
  The image is distorted or runs off . –	Check	PC adjust	menu	or	Screen	menu	and	adjust	them.			
		 			See	pages	30-31,	34-35.
  PIN code dialog box appears 	 –	PIN	code	lock	is	being	set.	Enter	a	PIN	code	(the	“1234”	or	numbers	
	 at start-up .	 	 you	have	set).	See	pages	19,	53-54.
  The Remote Control does 	–	Check	the	batteries.	
	 not work . 	 –	Make	sure	no	obstruction	is	between	the	projector	and	remote	 	
		 			control.	
		 –	Make	sure	you	are	not	too	far	from	the	projector	when	using...

66
wARNING :
High voltages are used to operate this projector . Do not attempt to open the cabinet .
If	problems	still	persist	after	following	all	operating	instructions,	contact	the	dealer	where	you	purchased	the	
projector	or	the	service	center.	Specify	the	model	number	and	explain	about	the	problem.	We	will	advise	you	
how	to	obtain	service.
This	symbol	on	the	nameplate	
means	the	product	is	Listed	
by	Underwriters	Laboratories	
Inc.		It	is	designed	and	
manufactured	to	meet	rigid	
U.L.	safety...

67
Appendix
Menu Tree
SVGA	1Mode	1Mode	2	-	-	-	-
Total	dotsHorizontalVertical
Display	area	HDisplay	area	VReset
Dynamic
RealBlackboard	(Green)
Image	1Image	2Image	3
Image AdjustContrastBrightnessColor	temp.
Red
Gamma
Store
NormalTrue
Digital	zoom	–
Full	
0–630–63
Computer Input
PC adjust
Mode	1Mode	2Mode	3Mode	4Mode	5
Image select
0–63
0–15
Image	1Image	2Image	3Image	4
Screen
Yes/No
	*	Systems	displayed	in	the	System	Menu	vary	 depending	on	an	input	signal.
ResetYes/No
Sharpness0–15
Computer Input/Video...

68
Appendix
AutoPA LSECAMNTSCNTSC	4.43PAL-MPAL-N
Video Input
Auto1080i1035i720p575p480p575i480i
Dynamic
CinemaBlackboard	(Green)
Image	1Image	2Image	3
Normal
0–630–63
Off
Image select
System (2)
System (3)
Image AdjustContrastBrightnessColorTint
RedGreenBlueSharpness
ResetStore
Gamma
Progressive
0–630–630–630–15	0–15
Image	1
Screen
Yes/No
Image	4
Standard
OffNoise	reductionL1L2
0–630–63
Image	2Image	3Image	4
L2L1
Film
Color	temp.
Wide
Scale
PositionCommonReset
H/V
H/VYes/NoYes/No
Custom
On/OffH&V...

69
Check	the	indicators	for	projector	condition.																																			
•	•	•	green.•	•	•	red•	•	•	off
•	•	•	blinks	green.
 When	the	projection	lamp	reaches	its	end	of	life,	the	LAMP	REPLACE	indicator	lights	yellow.	When	this	
								indicator	lights	yellow,	replace	the	projection	lamp	with	a	new	one	promptly.	(pp.	55,	61)
The	projector	is	off.	(The	AC	power	cord	is	unplugged.)
The	projector	is	in	stand-by	mode.	Press	the	ON/STAND-BY	button	
to	turn	on	the	projector.
Projector...

70
AppendixCompatible Computer Specifications
Basically	this	projector	can	accept	the	signal	from	all	computers	with	the	V- , 	H-Frequency	mentioned	below	
and	less	than	140	MHz	of	Dot	Clock. 		When	selecting	these	modes,	PC	adjustment	can	be	limited.
Note:
	 	 The	specifications	are	subject	to	change	without	notice.
ON-SCREEN  DISPLAyRESOLUTIONH-Freq .(KHz)V-Freq . (Hz)
VGA	1640	x	48031.4759.88
VGA	2720	x	40031.4770.09
VGA	3640	x	40031.4770.09
VGA	4640	x	48037.8674.38
VGA	5640	x	48037.8672.81
VGA	6640...