Eiki Lc-Xb42n Multimedia Projector Owners Manual

61
Maintenance and Cleaning
When  the  projection  lamp  of  the  projector  reaches  its  end  of 
life,  the  Lamp  replacement  icon  appears  on  the  screen  and 
LAMP REPLACE indicator lights yellow. Replace the lamp with 
a  new  one  promptly.  The  timing  when  the  LAMP  REPLACE 
indicator should light is depending on the lamp mode.
Follow these steps to replace the lamp.
Lamp
ORDER REPLACEMENT LAMP
Replacement lamp can be ordered through your dealer.  When ordering a projection lamp, give the...

62
Maintenance and Cleaning
This projector uses a high-pressure lamp which must be handled carefully\
 and properly.  
Improper handling may result in accidents, injury, or create a fire hazard.
● Lamp life may differ from lamp to lamp and according to the environment of use. There is no guarantee of  the  same  life  for  each  lamp.  Some  lamps  may  fail  or  terminate  their  life  in  a  shorter  period  of  time 
than other similar lamps.
●  If  the  projector  indicates  that  the  lamp  should...

6
 Problem:  – Solutions
  No power  – Plug the power cord of the projector into the AC outlet. 
    –

  See if the POWER indicator lights red. 
    –

   Wait until the POWER indicator stops blinking to turn on the projector 
again. The projector can be turned on after the POWER indicator 
turns red. (See page 22)
    –

  Check the WARNING indicator. If the WARNING indicator lights red,  
     projector cannot be turned on. (See page 58) 
    –

  Check the projection lamp. (See page 61) 
    –...

64
Appendix
 No image  – Check the connection betw een your computer or video equipment  
     and the projector. (See pages 19-21) 
    –

  See if the input signal is correctly output from your computer. Some  
     laptop computers may need to change the setting for monitor output  
       when connecting to a projector. See your computer’s instruction  
     manual for the setting.  
    –

  It takes about 30 seconds to display an image after turning on the  
     projector. (See page 22)
    –...

65
Appendix
 The image is distorted or runs off .  – Check "PC adjustment" menu or "Screen" menu and adjust them.  
     (page 33-34, 38-39)
  PIN code dialog box appears  – PIN code lock is being set. Enter a PIN code (the “1234” or numbers 
  at start-up  .
    you have set). (See pages 22, 54–55)
  Page Up/Down function does        – Make sure your computer is connected to the projector with USB  
  not work  .
      cable.(see page 19)             
    – Check cable connection between...

66
wARNING :
High voltages are used to operate this projector  . Do not attempt to open the cabinet .
If problems still persist after following all operating instructions, co\
ntact the dealer where you purchased the 
projector or the service center. Specify the model number and explain about the problem. We will advise you 
how to obtain service.
This  symbol  on  the  nameplate 
m e a n s  t h e  p r o d u c t  i s  L i s t e d 
by  Underwriters  Laboratories 
I n c .   I t   i s   d e s i g n e d   a...

67
Appendix
Menu Tree
SVGA 1Mode 1Mode 2 - - - -
Auto PC Adj.
Total dotsHorizontalVertical
Display area HDisplay area VReset
Dynamic
RealBlackboard (Green)Image 1Image 2Image 3
Image AdjustContrastBrightnessColor temp.
Red
Gamma
Store
Quit
NormalTrue
Digital zoom –
Full 
0–630–63
Computer Input
PC Adjust
Mode 1Mode 2Mode 3Mode 4Mode 5
Image Select
High
0–63
0–15
Image 1Image 2Image 3Image 4
Screen
Quit
Yes/No
*  
Systems displayed in the System Menu vary 
depending on an input signal.
ResetYes/No...

68
Appendix
AutoPALSECAMNTSCNTSC 4.43PAL-MPAL-N
Video Input
Auto1080i1035i720p575p480p575i480i
Dynamic
CinemaBlackboard (Green)
Image 1Image 2Image 3
Quit
Normal
0–630–63
Off
Setting
Image Select
System (2)
System (3)
Image AdjustContrastBrightnessColorTint
RedGreenBlueSharpness
ResetStore
Gamma
Progressive
0–630–630–630–15 0–15
Image 1
Screen
Yes/No
Quit
Image 4
LanguageSetting16 languages provided.
On/OffOn/Countdown off/Off Logo select
On/OffOn/Off
Off
On/Off
Code 1–Code 8
KeystoneBlue...

69
Check the indicators for projector condition.                           \
         
• • • green.• • • red• • • off
• • • blinks green.
When the projection lamp reaches its end of life, the LAMP REPLACE indicator lights yellow. When this indicator 
lights  yellow,  replace  the  projection  lamp  with  a  new  one  promptly.  Reset  the  lamp  replacement  counter  after 
replacing the lamp. See pages 61-62.
The projector is off. (The AC power cord is unplugged.)
The  projector  is  in  stand-by  mode....

70
AppendixCompatible Computer Specifications
Basically this projector can accept the signal from all computers with t\
he V-, H-Frequency mentioned below 
and less than 140 MHz of Dot Clock for analog signal and 110 MHz of Dot Clock for digital signal.   When selecting these modes, PC adjustment can be limited.
ON-SCREEN 
DISPLA yRESOLUTIONH-Freq .
(KHz)V-Freq . (Hz)
VGA 1640 x 48031.4759.88
VGA 2720 x 40031.4770.09
VGA 3640 x 40031.4770.09
VGA 4640 x 48037.8674.38
VGA 5640 x 48037.8672.81
VGA 6640 x...