Eiki Lc-Xb42 Multimedia Projector Owners Manual

11

Part Names and Functions
Top Control
①
②
④
⑥
⑦
⑧
① LAMP REPLACE indicator
  Lights  yellow  when  the  projection  lamp  reaches  its 
end of life (pp.57, 65).
⑦ w ARNING indicator
  – Lights red when the projector detects an abnormal 
condition. 
  – Blinks  red  when  the  internal  temperature  of  the 
projector exceeds the operating range (pp.54, 65).② ON/STAND–By  button
Turn the projector on or off (pp.19–20).⑧ POwER indicator
  – Lights red when the projector is in stand-by mode.
  – Lights...

12

Part Names and Functions
To  ensure  safe  operation,  please  observe  the  following precautions :
–   Do not bend, drop the remote control or expose the remote 
control to moisture or heat.–    For  cleaning,  use  soft  dry  cloth.    Do  not  apply  benzene, thinner, splay or any chemical material.
⑤
③
⑨
⑬
④
⑭
⑫
① ON/STAND-By  button 
  Turn the projector on or off.  (pp.19, 20)
② VIDEO button
  Select VIDEO input source.  (pp.25, 36)
③ COMPUTER button
  Select COMPUTER input source.  (pp25,...

13

Part Names and Functions
Adjustable Feet
Point  the  remote  control  toward  the  projector  (Infrared 
Remote  Receiver)  when  pressing  the  buttons.  Maximum 
operating  range  for  the  remote  control  is  about  16.4'(5  m) 
and 60 degrees in front of the projector.
Remote Control Operating Range
Projection angle can be adjusted up to 8.9 degrees with the 
adjustable feet. 
Lift the front of the projector and pull the feet lock latches on 
both side of the projector upward.
Release the...

14

Positioning the Projector
For  projector  positioning,  see  the  figures  below. The  projector  should  be  set  perpendicularly  to  the  plane  of  the 
screen.
Notes:
  • The  brightness  in  the  room  has  a  great  influence  on  picture  quality.  It  is  recommended  to  limit  ambient 
lighting in order to obtain the best image.
  • All measurements are approximate and may vary from the actual sizes.
Installation
Screen Size(W x H) mm4 : 3 aspect ratio
Zoom (min)
40”
Zoom (max)
813 x...

15

Installation
Connecting the AC Power Cord
This  projector  uses  nominal  input  voltages  of  100-120  V 
or  200–240  V  AC  and  it  automatically  selects  the  correct 
input voltage. It is designed to work with single-phase power 
systems  having  a  grounded  neutral  conductor.  To  reduce 
the risk of electrical shock, do not plug into any other type of 
power system.
If  you  are  not  sure  of  the  type  of  power  being  supplied, 
consult your authorized dealer or service station....

16

Installation
Connecting to a Computer

Cables used for connection 
• VGA Cable (Mini D-sub 15 pin)*
• Audio Cables
(*One cable is supplied; other cables are not supplied with the projector\
.)
External Audio Equipment
Audio cable 
(stereo)
Audio Output
COMPUTER
/COMPONENT
AUDIO IN
AUDIO OUT 
(stereo)
Audio Input
COMPUTER IN 1
Notes:
 • I n p u t   s o u n d   t o   t h e   C O M P U T E R / C O M P O N E N T 
AUDIO  IN  terminal  when  using  the  COMPUTER  IN  1 
and  the  COMPUTER  IN  2  /...

17

Installation
Connecting to Video Equipment
Cables used for connection  
• Video and Audio Cable (RCA x 3)
• S-VIDEO Cable
• Audio Cable
(Cables are not supplied with the projector.)
External Audio Equipment
Audio cable
(stereo)
VIDEOS-VIDEO
S-video cableVideo and 
audio cable
Composite Video and Audio OutputS-video Output
AUDIO IN
Audio Input
AUDIO OUT 
(stereo)
(R)(L)(Video)
U n p l u g   t h e   p o w e r   c o r d s   o f 
both  the  projector  and  external 
equipment  from  the  AC  outlet...

18

Installation
Connecting to Component Video Equipment
Cables used for connection 
• Audio Cables
• Scart-VGA Cable
• Component Cable
• Component-VGA Cable
(Cables are not supplied with the projector.)
External Audio Equipment
Audio cable
(stereo)
Audio cable 
(stereo)
Audio Input
Component Video Output
(Y, Pb/Cb, Pr/Cr)
RGB Scart 
21-pin OutputAudio Output
Scart-VGA 
cable
Component-
VGA cable
AUDIO OUT 
(stereo)
Component 
cable
COMPUTER IN 2/COMPONENT IN
COMPUTER/COMPONENT AUDIO IN
Notes:
 • When...

19

The preparation display will disappear 
after 30 seconds.
(See page 49 for Lamp control status.)
Lamp control status
Turning On the Projector
Connect  the  projector ’s  AC  power  cord  into  an  AC 
outlet. The POWER indicator lights red. Open the slide 
shutter (see pages 9,56).
Press  the  ON/STAND-BY  button  on  the  top  control 
or    on  the  remote  control.  The  POWER  indicator 
lights  green  and  the  cooling  fans  start  to  operate.  The 
preparation  display  appears  on  the...

20

TO  MAINTAIN  THE  LIFE  OF  THE  LAMP,  ONCE  YOU 
TURN  THE  PROJECTOR  ON,  WAIT  AT  LEAST  FIVE 
MINUTES BEFORE TURNING IT OFF.
“Power off?” disappears after 4 seconds.
Turning Off the Projector
Press  the  POWER  ON/STAND-BY  button  on  the  top 
control  or  on  the  remote  control,  and  “Power  off?” 
appears on the screen.
Press the POWER ON/STAND-BY button again to turn 
off  the  projector.  The  POWER  indicator  starts  to  blink 
red, and the cooling fans keep running. (You can...