Eiki Eip-4500l Dlp Projector Owners Manual

36
Connecting to a Monitor That Has an RGB Input Terminal
You can display computer images on a monitor using the RGB cables.
Note
•RGB signals and component signals input from the INPUT 1 or INPUT 2 terminals can be output to the
monitor.
•For inputting video signals from the INPUT 1 terminal, another RGB cable (commercially available) is
required.
Connecting to an Amplifier or Other Audio Equipment
Audio signals input from equipment connected to each audio input terminal of the projector
can be output...

37
Turning the Projector On/Off
Info
• English is the factory preset language. If you want to
change the on-screen display to another language,
change the language according to the procedure on
page  89.
▼On-screen Display
Info
•Do not unplug the power cord during projection or cool-
ing fan operation. The cooling fan in this projector contin-
ues to run for about 90 seconds after the projector enters
the standby mode. This can cause damage due to rise in
internal temperature, as the cooling fan also...

38
Image Projection
Shifting the Lens
In addition to the zoom function and adjustment of projection angle usin\
g the adjust-
ment feet, you can adjust the position of the projection using the lens \
shift function.
This is a useful function in cases such as when the screen can not be mo\
ved.
Adjustable range
The adjustable range is shown below.
Horizontal range: ±15%
Vertical range: +50% (to the upper side)
The adjustable range has limitations even within the range shown above.
The image can be...

39
Using the Adjustment Feet
•When the position of the projected image cannot be adjusted with the lens shift function, use the adjustment
feet to adjust the projected angle.
•The height of the projector can be adjusted using the adjustment feet when the screen is located higher than
the projector, the screen is inclined or when the installation site is slightly inclined.
•Install the projector so that it is as perpendicular to the screen as possible.
1While lifting the projector, rotate
the adjustment...

40
Note
•After you have pressed the FOCUS but-
tons or the ZOOM buttons on the remote
control or the projector, you can display the
test pattern by pressing the ENTER but-
ton. The test pattern is useful for making
more accurate adjustments.
•For fine adjustments, when pressing the
H & V LENS SHIFT buttons, the FOCUS
buttons or the ZOOM buttons, the pro-
jected image moves a small amount toward
the desired direction for approximately one
second. Hold down the buttons to move
the projected image quickly....

41
ENTER button
KEYSTONE 
button
UNDO button
Adjustment
button 
(' /" /\ /| ) 
Mouse/adjustment 
button (
'/"/\/|)
ENTER button
UNDO button
KEYSTONE
b
utton
For correcting an image desig-
nating the corner of the pro-
jected image.
For correcting an image desig-
nating the horizontal or vertical
axes.
For correcting the image distor-
tion which cannot be corrected
with “H & V KEYSTONE”.
*Only when “H & V KEY-
STONE” is set to the values
other than “0”, “IMAGE
RESIZING” can be adjusted....

42
Geometric Adjustment
Upper Left Upper Right Lower RightLower Left
GEOMETRIC ADJUSTMENT
1Press  on the projector or
 on the remote control re-
peatedly until “GEOMETRIC
ADJUSTMENT” is displayed.
2Press the buttons below to ad-
just the position, size or focus
of the projected image.
• Match screen’s four sides to green
test pattern.
• Pressing 
'
' '
'
' , 
"
" "
"
" , 
\
\ \
\
\  or 
|
| |
|
|  on the projector
or 
  on the remote  control allows you
to shift...

43
Vertical Keystone Correction
(Adjustment with 
'  / ")
H & V KEYSTONE
1Press  on the projector or
 on the remote control re-
peatedly until “H & V KEY-
STONE” is displayed.
• When the correction has already been
made with “GEOMETRIC ADJUST-
MENT”, the confirmation message for
resetting the correction before “H & V
KEYSTONE” is displayed, and then re-
set.
2Press  ' or  " to parallelize the
left and right sides of the pro-
jected image.
3Press  \ or  |
 
   
 
  to parallelize the
upper...

44
Image Projection
IMAGE RESIZING
(Adjustment with 
' / "  / \ /  |)
5Press  ', " , \  or  | to correct
the image distortion.
6Press   or  to set the posi-
tion. 

45
Switching the Input
Mode
Select the appropriate input mode for the con-
nected equipment.
Press  ,  ,  ,  or  on
the remote control to select the input
mode.
• •• •
•When pressing  on the projector, the
input mode switches in order of :
INPUT 1 INPUT 2 INPUT 3
• •• •
•When pressing  on the projector, the
input mode switches between “INPUT 4” and
“INPUT 5”.
Note
•When no signal is received, “NO SIGNAL”
will be displayed. When non-supported sig-
nal is received, “NOT REG.” is displayed.
•When “Auto...