Eiki Eip-4500l Dlp Projector Owners Manual

86
Helpful Functions Set during Installation (“Options (2)” menu)
Selecting the Transmis-
sion Speed (RS-232C)
Make sure that both the projector and computer
are set for the same baud rate.
Menu operation  Page 58
Example: “Options (2)” screen menu
Description of RS-232C
Note
•Refer to the “SETUP GUIDE” contained on the
supplied CD-ROM for RS-232C Specifications
and Command Settings.
•Refer to the computer owner’s manual for
instructions for setting the computer’s baud rate.
Description
Transmission...

87
Monitor Output Settings
When the Monitor Out has been set to “Enable”,
the monitor output is activated and power is con-
sumed even in the standby mode. It is recom-
mended that the Monitor Out be set to “Disable”
when it is not connected. This reduces power
consumption when the projector is in the standby
mode.
Menu operation  Page 58
Example: “Options (2)” screen menu
Description of Monitor Out
Description
The monitor output function is activated
even if the projector is in standby mode.
The monitor...

88
Returning to the Default
Settings
This function allows you to initialize the settings
you have made in the projector.
Menu operation  Page 56
Example: “Options (2)” screen menu
Note
About the network settings
•“IP Address”, “Subnet Mask”, “Default Gateway”
and other network setting items are initialized.
The following items or menu cannot be initialized.
•“C. M. S.” menu
“Lightness”, “Chroma” and “Hue” respectively
saved for Custom 1-3 on the “C.M.S.” menu.
•“Fine Sync” menu
Special Modes
•“Options...

89
Selecting the On-screen
Display Language
The projector can switch the on-screen display
language among 11 languages: English, German,
Spanish, Dutch, French, Italian, Swedish, Portu-
guese, Chinese, Korean or Japanese.
Menu operation  Page 58
Example: “Language” screen menu
Using the Other Menus (“Language” and “Status” menus)
Overview of All Menu Set-
tings
This function can be used to display all the ad-
justed settings as a list on the screen.
Menu operation  Page 58
Example: “Status” screen menu...

90
Cleaning the air vents and the intake vent cover
■Use a vacuum cleaner to clean dust from the ex-
haust vent, the intake vents and the intake vent
cover (on the bottom of the projector).
Info
•If you want to clean the air vents and the intake
vent cover during projector  operation, be sure
to press 
  on the projector or  on the re-
mote control and put the projector into standby
mode. After the cooling fan has stopped, un-
plug the power cord from the AC socket and
clean the air vents and the intake...

91
Power indicator
Lamp indicators 1, 2
T emperature warning indicator
Maintenance Indicators
Maintenance Indicators
■ The warning lights on the projector indicate problems inside the project\
or.
■ If a problem occurs, either the temperature warning indicator or the lam\
p indicator will illuminate
red, and the projector will enter the standby mode. After the projector has entered the standby
mode, follow the procedures given below.
About the temperature warning indicator
If the temperature inside the...

92
Maintenance indicatorProblemCause Possible solution
T emperature
warning
indicator Normal
Abnormal
Off Red on
(Standby) The internal
temperature is
abnormally high.
Abnormal
•
 Blocked air intake •
Relocate the projector to an area
with proper ventilation. (See page
9.)
• Cooling fan break-
down
• Internal circuit failure
• Clogged air intake
• Clogged intake vent
cover •
Take the projector to your nearest
EIKI Authorized Dealer or Service
Center for repair.
• Clean the air vents and the intake
vent...

93
Lamp
■It is recommended that the lamp units (optional: AH-45001 and AH-45002) be replaced when the re-
maining lamp life becomes 5% or less, or when you notice a significant deterioration in the picture
and color quality. The lamp life (percentage) can be checked with the on-screen display. See page 83.
■Purchase a replacement lamp unit of type AH-45001 and AH-45002 from your place of purchase,
nearest EIKI Authorized Dealer or Service Center.
Caution Concerning the Lamp
■This projector utilizes a...

94
Regarding the Lamp
Optional
accessories
Lamp unit 1
AH-45001Removing and Installing
the Lamp Unit
Info
• Make sure that you remove the lamp unit
by the handle. Do not touch the glass sur-
face of the lamp unit or the inside of the
projector.
• To  avoid injury to yourself and damage to
the lamp, be sure to carefully follow the
steps below.
• Do not loosen other screws except for the
lamp unit cover and lamp unit.
(Only the silver screws are loosened.)
1Press  on the projector or
 on the remote control...

95
4Remove the lamp unit.
•Loosen the securing screws (two for
each lamp) from the lamp unit. Hold the
lamp unit by the handle and pull it in the
direction of the arrow. At this time, keep
the lamp unit horizontal and do not tilt it.
5Insert the new lamp unit.
•Press the lamp unit firmly into the lamp
unit compartment. Fasten the securing
screws.
•Be sure that AH-45001 and AH-45002
are respective type.
6Replace the lamp unit cover.
•Align the lamp unit cover and slide it to
close. Then tighten the user...