Eiki Eip-4500l Dlp Projector Owners Manual

16
Note
•All the buttons on the remote control, except the mouse/adjustment button and the ADJ./MOUSE switch,
are made of luminous material that is visible in the dark. Visibility will diminish over time. Exposure to
light will recharge the luminous buttons.
Remote Control
4018
56
39
40
45
70
18
48
37
47
19
41
46
50
46
46
50
47
STANDBY-ON button
For turning the power on or putting 
the projector into standby mode.
ZOOM buttons
For adjusting the projected 
image size.
KEYSTONE button
For entering the...

17
Using the Remote Control
Inserting the Batteries
The batteries (two R-6 batteries (“AA” size,
UM/SUM-3, HP-7 or similar)) are supplied in
the package.
1Press the tab and lift open the battery
cover in the direction of the arrow
.
2Insert the batteries.
•Insert the batteries making sure the po-
larities correctly match the 
 and 
marks inside the battery compartment.
3Insert the tabs on the end of the
battery cover into their slots and
press the cover into position.
Incorrect use of the batteries may...

18
Using the Remote Control
Using the Remote Control with a Signal Cable
When the signals from the remote control cannot be reached due to the range or positioning of the projec-
tor, you can connect the remote control to the projector with a ø3.5 mm minijack cable (commercially available).
Switching the Remote Control Mode
The remote control has two functions. One is projector control and the other is wireless computer mouse.
Slide the ADJ./MOUSE switch on the remote control to other side compatible to...

19
Using the Remote Control as a Wireless Computer Mouse
When connecting the supplied remote
mouse receiver to the computer, you can use
the remote control as the wireless computer
mouse.
1Connect the supplied remote
mouse receiver to the USB termi-
nal on the computer.
2Slide the ADJ./MOUSE
switch on the remote con-
trol to the MOUSE position.
3Use the mouse function.
•Point the remote control at the remote
mouse receiver.
■When moving the cursor
Press '/"/\/|.
■When left-clicking
Press 
.
■When...

20
Quick Start
Page 22
1.Place the projector facing a screen
Pages 27, 37
Page 37
Press  on the projector or  on the remote control. This section shows the basic operation (projector connecting with the computer). For details, see the page
described below for each step.
Setup and Projection
In this section, connection of the projector and the computer is explained using one example.
2.Connect the projector to the computer and plug the power
cord into the AC socket of the projector
3.Remove the lens cap...

21
Pages 38, 39
4.Adjust the angle
5.Adjust the focus and the zoom
Page 40
8.Turn the power off
Page 37
7.Select the input mode
Page 45
1 11 1
1Press  on the projector or  on the remote control to adjust the focus.
2 22 2
2Press 
 on the projector or  on the remote control to adjust the zoom.
Press  on the projector or  on the remote control to select the “INPUT 1” mode.
• •• •
•When pressing  on the projector, input mode switches in order of : INPUT 1 INPUT 2 INPUT 3.
Pressing 
 on the projector...

22
Setting Up the Projector
Position the projector perpendicular to the screen with the projector’s feet flat and level to achieve an
optimal image.
Note
•The projector lens should be centered in the middle of the screen. If the horizontal line passing through
the lens center is not perpendicular to the screen, the image will be distorted, making viewing difficult.
•For an optimal image, position the screen so that it is not in direct sunlight or room light. Light falling
directly on the screen washes...

23
Projecting a Reversed Image
Projection from behind the Screen
■Place a translucent screen between the projector and the audience.
■Reverse the image by setting “Rear” in the “PRJ Mode” menu. (See page 84.)
Projection Using a Mirror
■Place a mirror (normal flat type) in front of the lens.
■When the translucent screen is placed between the mirror and audience, set to “Front” in the “PRJ Mode”
menu. (See page 84.)
■When the mirror is placed on the audience side, set to “Rear” in the “PRJ Mode” menu. (See...

24
INPUT/OUTPUT Terminals and Connectable Main Equipment
AUDIO input (2, 3) terminalConnecting an audio cable. (Shared 
audio input terminal for INPUT 2 
and 3.) (See pages 28 and 29.) 
AUDIO input (1) terminalConnecting an audio cable. 
(Audio input terminal 
dedicated to INPUT 1.) (See 
page 27.)
AUDIO input (4, 5) terminalsConnecting an audio cable. 
(Shared audio input terminals for 
INPUT 4 and 5.) (See page 34.)
WIRED REMOTE terminalFor connecting the remote control when 
the signals from the...

25
Terminal on the
projector
INPUT 1
INPUT 2
INPUT 3
AUDIO  (for INPUT 1)
AUDIO (for INPUT 2, 3)
INPUT 3
INPUT 2
INPUT 2
Equipment
Computer
Audio-visual
equipment
T
erminal on
connected equipment
RGB
output
terminal
DVI digital
video
output
terminal
Audio
output
terminal
HDMI
output
terminal
DVI digital
video
output
terminal
RGB
output
terminal
Component video
output
terminal Cable
RGB cable (supplied)
5 BNC to 15-pin D-sub cable (commercially available)
DVI Digital cable (commercially available)
ø3.5 mm...