Eiki Eip-2600 Dlp Projector Owners Manual

19
300
200
100 80
40
3610(11.2 m)247–284
(7.5 m – 8.6 m)123–142
(3.7 m – 4.3 m)910–114
(3.0 m – 3.5 m)411–58
(1.5 m – 1.7 m)
240 ×180
160×12080×6064×4832×24
Projection (PRJ) Mode
The projector can use any of the 4 projection modes shown in the diagram below. Select the mode
most appropriate for the projection setting in use.  (You can set the PRJ mode in “SCR-ADJ” menu.
See page  44.)
■ Table mounted, front projection
[Menu item  ➞ “Front”] ■
Ceiling mounted, front projection
[Menu item  ➞ “Ceiling +...

20
Setting up the Projector (Continued)
300
(762 cm)
250 
(635 cm)
200 
(508 cm)
150 
(381 cm)
120 
(305 cm)
100 
(254 cm)
80 
(203 cm)
70 
(178 cm)
60 
(152 cm)
40 
(102 cm) 610 cm (240

)
508 cm (200 
)
406 cm (160 
)
305 cm (120 
)
244 cm (96 
)
203 cm (80 
)
163 cm (64 
)
142 cm (56 
)
122 cm (48 
)
81 cm (32 
) 19 cm
16 cm
13 cm
10 cm
8 cm
6 cm
5 cm
4 cm
4 cm
3 cm (7 9/16

)
(6 19/64
 )
(5 3/64
 )
(3 25/32
 )
(3 1/32
 )
(2 33/64
 )
(2 1/64
 )
(1 49/64
 )
(1 33/64
 )
(1 1/64
 )
457 cm (180

)
381 cm...

21
Before connecting, ensure that the power cord of the projector is unplugged from the AC
outlet and turn off the equipment to be connected. After making all conn\
ections, turn on the
projector and then the other pieces of equipment. When connecting a computer, ensure that
it is the last equipment to be turned on after all the connections are m\
ade.
IMPORTANT:
Ensure that the appropriate input mode has been selected on the projector before
you turn on the connected equipment.
•For more details of...

22
Connecting the Projector to Other Equipment (Continued)
S-VIDEO
VIDEO
COMPUTER/
COMPONENT
Equipment
Video equipment
Camera/Video game CableS-video cable (commercially available)
Video cable (commercially available)
Cables for a camera or a video game
Cables for a camera or a video game Cables for a camera or a video game/3 RCA
to mini D-sub 15 pin cable (supplied)
Terminal on 
connected equipmentTerminal on the projector
S-video output
terminal
Video
output
terminal S-video
output
terminal
Video...

23
Note
•Only for EIP-2600:
- When using the ø3.5 mm mono audio cable, the volume level will be hal\
f of when using the ø3.5
mm stereo audio cable.
-Y ou can select “Audio 1” or “Audio 2” for “Audio Input”\
 in the “PRJ-ADJ” menu. (See page  46.)
• RGB signals and Component signals can be output to the monitor.
Equipment CableTerminal on 
connected equipmentTerminal on the projector
Audio
output
terminal
Monitor
AmplifierMONITOR OUT
AUDIO OUTRGB
input
terminalRGB cable (supplied or commercially...

24
Connecting the Power Cord
Plug the supplied power cord into the
AC socket on the rear of the projector.
Then plug into AC outlet.
AC socket
To  AC outlet Power cord
(supplied)
Controlling the Projector by a Computer
When the RS-232C terminal on the projector is connected to a computer with a DIN-D-sub RS-
232C adaptor and an RS-232C serial control cable (cross type, commercially available), the com-
puter can be used to control the projector and check the status of the projector. See page 
57 for...

25
Turning the Projector On/Off
On-screen display (confirmation message)
• When “Auto Restart” is set to “On”:
If the power cord is unplugged from the outlet
or the breaker switch is turned off when the
projector is on, then the projector automati-
cally turns on when the power cord is plugged
into the AC outlet or the breaker switch is
turned on. (See page  45.)
• English is the factory default language. If you
want to change the on-screen display to an-
other language, change the language accord-
ing...

26
About the Setup Guide
After turning on the projector, the Setup
Guide screen appears to assist you with
projector setup.
Guidance items
1 FOCUS
2 HEIGHT ADJUST
3 ZOOM
Press ENTER  to exit the Setup Guide
screen.
Image Projection
Setup Guide screen
Note
• The Setup Guide screen automatically high-
lights the items in the following order:
1 FOCUS
3 ZOOM
4 ENTER 2 HEIGHT ADJUST
However, you can adjust the focus, height
(angle), or zoom regardless of the highlighted
item.
• If you do not want to display...

27
3 Adjusting the Height
The height of the projector can be ad-
justed using the adjustment feet at the
front and rear of the projector.
When the screen is above the projec-
tor, the projection image can be made
higher by adjusting the projector.
1
2
3
•Do not apply too much pressure on the pro-
jector when the front adjustment foot comes
out.
• When lowering the projector, be careful not to
get your fingers caught in the area between
the adjustment foot and the projector.
•
Hold the projector firmly...

28
0
KEYSTONEADJUST END
Correcting Trapezoidal
Distortion
When the image is projected either from
the top or from the bottom towards the
screen at an angle, the image becomes
distorted trapezoidally. The function for
correcting trapezoidal distortion is
called Keystone Correction.
1
2
3
Press  KEYSTONE .•The on-screen display of the Keystone
Correction mode will disappear.
•Y ou can also use  KEYSTONE on the pro-
jector.
Press  P/Q  or  O/R  to adjust the
Ke ystone Correction.
•Y ou can also adjust the...