Eiki Eip 1500t Dlp Dlp Projector Owners Manual

28
Turning the Projector On/Off
Info
• English is the factory preset language. If you want to
change the on-screen display to another language,
change the language according to the procedure on
page  52.
Lamp
indicator
Power indicator
STANDBY-ON button
Lens cap
ON button
STANDBY
button
▼ On-screen Display
Info
•Do not unplug the power cord during projection or cool-
ing fan operation. The cooling fan in this projector contin-
ues to run for about 90 seconds after the projector enters
the standby mode....

29
Switching the INPUT
Mode
Select the appropriate input mode for the con-
nected equipment.
Press  ,  ,  ,  ,  or  on
the remote control to select the input
mode.
•
• •
•
• When pressing  on the projector, input mode
switches in order of :
INPUT 1 INPUT 2 INPUT 3 INPUT 5 INPUT 4
DIGITAL
Note
•When no signal is received, “NO SIGNAL”
will be displayed. When a signal that the
projector is not preset to receive is received,
“NOT REG.” will be displayed.
• The INPUT mode is not displayed when
“OSD Display”...

30
Image Projection
ZOOM-FOCUS 
button
Adjustment buttons
( ' /" /\ /| )
Adjustment
buttons (
' /" /\ /| )
ZOOM-FOCUS
button
Adjusting the Focus
1Press  on the remote control.
2Press  \ or  | on the remote con-
trol to adjust  the focus.
Note
•You can also adjust the focus by using
 and \
\ \
\
\ or |
| |
|
| on the projector.
Adjusting the Projected Image Size
1Press   on the remote control.
2Press  ' or  " on the remote con-
trol to adjust  the zoom.
Note
•You can also adjust...

31
Using the Adjustment
Feet
The height of the projector can be adjusted
using the adjustment feet at the front and rear
of the projector when the screen is located
higher than the projector, the screen is inclined
or when the installation site is slightly inclined.
Install the projector so that it is as perpen-
dicular to the screen as possible.
1Lift the projector to adjust its
height while pressing the
HEIGHT ADJUST button.
•The projector is adjustable up to approxi-
mately 12 degrees (6 steps).
•...

32
"On-screen Display (Keystone Correction mode)
KEYSTONE
button
UNDO
button Adjustment
buttons (
'
/" /\ /| )
Horizontal Keystone Correction
Vertical Keystone Correction
Note
• When adjusting the Keystone setting, the placement
range is changed depending on the input signal
type.
• Keystone correction cannot be applied to On-screen
Display.
• When Keystone correction is applied, the resolution
of image can be deteriorated to some extent.
• Keystone Correction is also returned to the factory...

33
Placement of the Projected Image
Using the Keystone Correction
Place the projector at a distance from the screen that
allows
 images to be projected onto the screen by referring
to “Screen Size and Projection Distance” on page 17.
: Screen area
Note
• The aspect ratio of the projected image also shifts
slightly when the “H Keystone” and “V Keystone”
functions are adjusted simultaneously.
• If you cannot correct trapezoidal distortion with
Keystone correction, change the placement
position of the...

34
Selecting the Picture Mode
You can select the picture setting (Memory)
directly stored in “Picture Mode” on the
“Picture” menu.
Press  on the remote control.
•Each time the button is pressed while the display
is on, the picture mode changes in order of:
Memory OFF Memory 1 Memory 2
Memory 5 Memory 4 Memory 3
Note
•This function can also be accessed from the
OSD menu (see page 44).
Switching the High Bright-
ness / High Contrast Mode
This function controls the quantity of the pro-
jected light and the...

35
480I480P576I576P
NTSC PAL
SECAM
540P
1080
I
720P
VGA
SVGA XGA
Input signal SIDE BAR SMART STRETCHOutput screen image
STRETCH CINEMA ZOOM
4:3 aspect ratio
Letterbox
16:9 aspect ratio
16:9 aspect ratio Squeeze
16:9 aspect ratio
4:3 aspect ratio
Note
• “SMART STRETCH” cannot be selected while the Keystone correction (page  32) is being adjusted.
• Keystone correction (page  32) is disabled while the picture mode is set to “SMART STRETCH”.
• 580
I/580P is displayed on the screen when signal 576I/576P is...

36
Menu Items
The following shows the items that can be set in the projector.
Note
•“Tint” cannot be used with PAL, SECAM, PAL-M, PAL-N or PAL-60.
• “Color”, “Tint”, “Sharp”, “Clock”, “Phase”, “H-Pos”, “\
V-Pos” and “Auto Sync” cannot be used in the DIGITAL
mode.
• “Fine Sync” menu cannot be displayed in the INPUT 3 and INPUT 4 mo\
des.
“Picture” menu
“Fine Sync” menu
Example: Screen for INPUT 1
mode
+30
-30
+30
-30
+30
-30
+30
-30
+30
-30
+30
-30
Tint Color
Sharp Bright
+30
-30Contrast
Red
Blue
Reset...

37
“Options” menu
“Language” menu
Lamp Timer (Life)
Options
Main Menu Sub Menu
OSD Display [ON/OFF]
Auto
PAL
NTSC3.58
SECAM
NTSC4.43
PAL-M
PAL-N
PAL-60 Video System
Background [Blue/None]
Eco Mode [Eco/Standard]
Auto Power Off [ON/OFF]
Center
Upper Right
Lower Right
Upper Left
Lower Left Menu Position
Page 47
Page 47 Page 47
Page 48
Page 49
Page 49
Page 50
Page 50
Page 51
*1
*2
*1: Item when selecting INPUT 3 or INPUT 4
*2: Item when selecting INPUT 5
RGB
Component Signal Type
Menu Color...