Dukane Projector 8933W User Manual

11
Setting up
• Plug-and-Play is a system composed of a computer, its operating system 
and peripheral equipment (i.e. display devices). This projector is VESA DDC 
2B compatible. Plug-and-Play can be used by connecting this projector to a 
computer that is VESA DDC (display data channel) compatible.
- 
 Take advantage of this feature by connecting a computer cable to the 
COMPUTER IN1 port (DDC 2B compatible). Plug-and-Play may not work 
properly if any other type of connection is attempted.
- 
 Please...

12
Connecting with your devices (continued)
• Before connecting the projector to a computer, consult the computer’s 
manual and check the compatibility of the signal level, the synchronization 
methods and the display resolution output to the projector. 
-  Some signal may need an adapter to input this projector.
-  Some computers have multiple screen display modes that may include some  signals which are not supported by this projector.
-  Although the projector can display signals with resolution up to...

13
Setting up
• The HDMI port of this model is compatible with HDCP (High-band-
width Digital Content Protection) and therefore capable of displaying a video 
signal from HDCP compatible DVD players or the like.
-  The HDMI supports the following signals. Video signal :  480i@60, 480p@60, 576i@50, 576p@50, 720p@50/60,  1080i@50/60, 1080p@50/60
Audio signal :  Format Linear PCM   Sampling frequency 48kHz / 44.1kHz / 32kHz 
-  This projector can be connected with another equipment that has HDMI
TM...

14
Connecting to a power supply
1.Put the connector of the power cord into the 
AC (AC inlet) of the projector.
2.Firmly plug the power cord’s plug into the 
outlet. In a couple of seconds after the 
power supply connection, the POWER 
indicator will light up in steady orange.
►Please use extra caution when connecting the power cord, as 
incorrect or faulty connections may result in fire and/or electrical shock.
• Do not touch the power cord with a wet hand.
• 
 Only use the power cord that came with the...

15
Using the security bar and slot
A commercially available anti-theft chain or 
wire can be attached to the security bar on 
the projector. Refer to the fi gure to choose 
an anti-theft chain or wire.
Also this product has the security slot for 
the Kensington lock. 
For details, see the manual of the security 
tool.
►Do not use the security bar and slot to prevent the projector 
from falling down, since it is not designed for it. WARNING
►Do not place anti-theft chain or wire near the exhaust vents....

16
Remote control
Installing the batteries
Please insert the batteries into the remote control before using it. If the remote control 
starts to malfunction, try to replace the batteries. If you will not use the remote control for 
long period, remove the batteries from the remote control and store them in a safe place.
1.Holding the hook part of the battery 
cover, remove it.
2.Align and insert the two AA batteries  
(HITACHI MAXELL ENERGY Part No.LR6  
or R6P) 
according to their plus and minus...

17
About the remote control signal
The remote control works with the projector’s remote 
sensor. This projector has a remote sensor on the front.
The sensor senses the signal within the following range 
when the sensor is active:60 degrees (30 degrees to the left and right of the sensor) 
within 3 meters about.
• The remote control signal refl ected in the screen or the like may be available. 
If it is diffi cult to send the signal to the sensor directly, attempt to make the signal refl ect.
• The remote...

18
1.Make sure that the power cord is firmly and 
correctly connected to the projector and the 
outlet.
Turning on the power
2.Make sure that the POWER indicator is 
steady orange (
72). 
3.Press STANDBY/ON button on the 
projector or the remote control.
The projection lamp will light up and POWER  
indicator will begin blinking in green. When the  
power is completely on, the indicator will stop blinking and light in steady 
green (
72).
Power on/off
To display the picture, select an input signal...

19
Power on/off
►A strong light is emitted when the projector’s power is on.  
Do not look into the lens of the projector or look inside of the projector through 
any of the projector’s openings.
►Do not touch around the lamp cover and the exhaust vents during use or just 
after use, since it is too hot. WARNING
1.Press the STANDBY/ON button on the projector or the remote control.  
The message “Power off?” will appear on the screen for about 5 seconds.
Turning off  the power
2.Press the STANDBY/ON...

20
Operating
1.
Adjusting the volume
Use the VOLUME +/VOLUME - buttons to adjust the volume.
A dialog will appear on the screen to aid you in adjusting the 
volume. If you do not do anything, the dialog will automatically 
disappear after ten seconds.
●  When 
 is selected for current picture input port, the volume 
adjustment is disabled. Please see AUDIO SOURCE item of AUDIO menu 
(
46).
●  Even if the projector is in the standby mode, the volume is adjustable when  both of the following conditions...