Dukane Projector 8933W User Manual

							1
Projector
User's Manual (detailed)  
Operating Guide
Thank you for purchasing this projector.►Before using this product, please read all manuals for this 
product. Be sure to read Safety Guide first. After reading them, store them in a 
safe place for future reference. WARNING
• The information in this manual is subject to change without notice.
• The illustrations in this manual are for illustrative purposes. They may differ 
slightly from your projector.
• The manufacturer assumes no responsibility for any errors that may appear in 
this manual.
• The reproduction, transfer or copy of all or any part of this document is not 
permitted without express written consent. NOTE
Trademark acknowledgment
Various symbols are used in this manual. The meanings of these symbols are 
described below. 
About this manual
WARNING
CAUTION
This symbol indicates information that, if ignored, could possibly 
result in personal injury or even death due to incorrect handling.
This symbol indicates information that, if ignored, could possibly 
result in personal injury or physical damage due to incorrect 
handling.
Please refer to the pages written following this symbol.

•  Mac® is a registered trademark of Apple Inc.
• 
 Windows®, DirectDraw® and Direct3D® are registered trademarks of Microsoft Corporation 
in the U.S. and/or other countries.
• 
 VESA and DDC are trademarks of the Video Electronics Standard Association.
• 
 HDMI, the HDMI logo, and High-Definition Multimedia Interface are trademarks or registered 
trademarks of HDMI Licensing LLC in the United States and other countries.
•  Blu-ray DiscTM and Blu-rayTM are trademarks of Blu-ray Disc  
Association.
All other trademarks are the properties of their respective owners.
NOTICE This entry notices of fear of causing trouble.
8933W
430-8933W-General-00.pdf 
						

							2
Contents
Introduction  . . . . . . . . . . . . . . .3
Features
 ......................3
Checking the contents of package ...3
Part names
 ....................4
Setting up
  . . . .

 . . . . . . . . . . . .
 .7
Arrangement
 ...................7
Connecting with your devices .....10
Connecting to a power supply .....14
Using the security bar and slot
 ....15
Remote control
  . . . .

 . . . . . . .
 .16
Installing the batteries
 ...........16
About the remote control signal
 ...17
Changing the frequency of remote 
control signal
 ..................17
Power on/of

f
  . . . .

 . . . . . . . . .
 .18
Turning on the power
 ...........18
Turning off the power
 ...........19
Operating
  . . . .

 . . . . . . . . . . .
 .20
Adjusting the volume
 ............20
Temporarily muting the sound
 .....20
Selecting an input signal
 .........21
Searching an input signal
 ........22
Selecting an aspect ratio
 .........23
Adjusting the projector's elevator
 . .24
Adjusting the zoom and focus
 .....24Using the automatic adjustment feature ...25
Adjusting the position
 ...........25Correcting the keystone distortions . .26
Using the magnify feature
 ........27
Temporarily freezing the screen
 ...28
Temporarily blanking the screen 
 . .28
Using the menu function 
 ........29
EASY MENU
 .  .  .  .  .  .  .  .  .  .  .  .  .  .  .31
Aspect,  Keystone, Picture mode,  Eco mode, Installation, Reset, Filter time, 
Language, Advanced menu, Exit
PICTURE menu  . . . .  . . . . . . . .33
Brightness, Contrast, Gamma, Color temp,  Color, Tint, Sharpness, My memory
IMAGE menu  . . . . . . . . . . . . . .36
Aspect, Over scan, V position, H position,   
H phase, H size, Auto adjust execute
INPUT menu  . . . .  . . . . . . . . . .39
Progressive, Video nr, Color space,  
Video format, Hdmi format, Hdmi range, 
Computer in, Frame lock, Resolution

SETUP menu  . . . . . . . . . . . . . .43
 Keystone, Auto eco mode, Eco mode, Installation, Standby mode, Monitor out
AUDIO menu  . . . .  . . . . . . . . . .46
Volume, Speaker, Audio source 
SCREEN menu  . . . . . . . . . . . . .47
Language, Menu position, Blank,  
Auto blank, Start up, 
MyScreen,  
M
yScreen Lock, Message, Source name, 
Template, C.c.
OPTION menu  . . . .  . . . . . . . . .53
Auto search, Direct power on,  
Auto power off, Lamp time, Filter time, 
My button, My source, Service
SECURITY menu  . . .  . . . . . . . .60
Security password change,  
MyScreen password, Pin lock,  
My text password, My text display,  
My text writing
Maintenance  . . . .  . . . . . . . . . .65
Replacing the lamp
 .............65
Cleaning and replacing the air filter . .67Other care ....................69
Troubleshooting
  . . . .
  . . . . . .
 .70
Related messages
 .............70
Regarding the indicator lamps
 ....72
Resetting all settings
 ............75Phenomena that may be easy  
to be mistaken for machine defects ...75
Specifications
  . . . .

 . . . . . . . .
 .79
 
						

							3
Introduction
Introduction
• Keep the original packing materials, for future reshipment. Be sure 
to use the original packing materials when moving the projector. Use special 
caution for the lens.
• The projector may make a rattling sound when tilted, moved or shaken, since 
a flap to control the air flow inside of the projector has moved. Be aware that 
this is not a failure or malfunction. NOTE
The projector provides you with the broad use by the following features.
Checking the contents of  package
ü    This projector has a variety of I/O ports that supposedly cover for any scene.
ü   
 This lightweight projector requires only a minimal amount of space for 
installation. 
ü   
 This projector has a capability to project various picture signals onto a screen.
Please see the  Contents of package section in the User’

s Manual (concise) 
which is a book. Your projector should come with the items shown there. Require 
of your dealer immediately if any items are missing.
Features
►Keep small parts away from children and pets. Take care 
not to put in the mouth. If swallowed, consult a physician immediately for 
emergency treatment. WARNING 
						

							4
Introduction
►Do not open or remove any portion of the product, unless the 
manuals direct it.
►Do not subject the projector to unstable conditions.
►Do not apply a shock or pressure to this product.
►Do not look into the lens and the openings on the projector while the lamp is 
on. WARNING
►Do not touch around the lamp cover and the exhaust 
vents during use or just after use, since it is too hot.
►Do not attach anything onto the lens because it could damage the lens, 
such as melting the lens.  CAUTION
(continued on next page)
Part names
(1) Lamp cover (65)
The lamp unit is inside. 
(2) Speaker (
20, 46)
(3) Filter cover (
67)
The air filter and intake vent are inside.
(4) Elevator feet (x2) (
24)
(5) Elevator button (
24)
(6) Remote sensor (
17)
(7) Lens (
69)
(8) Intake vents
(9) Control panel (
5)
(10) FOCUS ring (
24)
(11) ZOOM  ring (
24)
(12) AC (AC inlet) (
14)
(13) Exhaust vent
(14) Rear panel (
5)
(7)
(4)(5) (6)
(8) (3)
(2)
(12) (13)
(14) (8)
(9)
(1)
(11)(10)
(4) 
						

							5
Introduction
Part names (continued)
Control panel 
(1) STANDBY/ON button (
18)
(2) INPUT button (
21)
(3) MENU button (
29) 
(4) LAMP indicator (
72)
(5) TEMP indicator (
72) 
(6) POWER indicator (
72)
Rear panel  (
10 ~ 13)
(1) HDMI port
(2) AUDIO IN 
(R,L) ports
(3) AUDIO OUT (R,L) ports
(4) COMPUTER IN1 port  (5) COMPUTER IN2 / MONITOR OUT port
(6) CONTROL port 
(7) VIDEO port
(8) Security slot (
15)
(9) Security bar (
15)
(continued on next page)
(1) (3)
(2) (6) (4)(5)
(5)
(4)(1)
(2)
(9) (8)
(3)
(7)
(6) 
						

							6
Introduction
Part names (continued)
Remote control 
(1) VIDEO button (
21) 
(2) COMPUTER button (
21)
(3) SEARCH  button (
22)
(4) STANDBY/
ON button (
18)
(5) ASPECT button (
23)
(6) AUTO button (
25)
(7) BLANK button (
28)
(8) MAGNIFY - ON
 button (
27)
(9) MAGNIFY - OFF  button (
27)
(10) MY SOURCE/DOC
.CAMERA  button  
(
22, 57)
(11) VOLUME - button (
20)
(12) PAGE 
UP button *
(13) PAGE DOWN button *
(14) VOLUME + button (
20)
(15) MUTE button (
20)
(16) FREEZE button (
28)
(17) MY BUTT
ON - 1 button (
56, 57)
(18) MY BUTTON
 - 2 button (
56, 57)
(19) KEYSTONE button (
26)
(20) POSITION  button (
25, 29)
(21) MENU button (
29)
(22) ▲/▼/◄/► cursor buttons (
29)
(23) ENTER button (
29) 
(24) ESC button (
29)
(25) RESET button (
29)
(26) Battery cover (
16)
B a c k   o f                            
the remote control
(2)
(1)
(6)
(5)
(16)
(8)
(9)
(19)
(17)
(20)
(22)
(24)
(10)
(4)
(3)
(7)
(12)
(14)
(11)
(13)
(15)
(18)
(21)
(23)
(25)
(26)
VIDEODOC.CAMERA
KEYSTONE
ASPECT
SEARCHBLANK
MUTE
MY BUTTON
POSITION ESC MENU
RESET
COMPUTER MY SOURCE/
AUTOMAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
o
9×VOLUME
 
ENTER
• Any button marked with “*” is not supported on this projector (71).
NOTE 
						

							7
Setting up
Setting up
Install the projector according to the environment and manner the projector will be 
used in.
For the case of installation in a special state such as ceiling mount, the specified 
mounting accessories (
Specifications in the User’s Manual (concise)) and 
service may be required. Before installing the projector, consult your dealer about 
your installation. 
Arrangement
Refer to tables T-1 or T-2 and figures F-1 and F-2 at the end of User’s Manual 
(concise) to determine the screen size and projection distance.
The values shown in the table are calculated for a full size screen.
(continued on next page) • 
 If the projector is used at an altitude of about 1600 m (5250 feet) or higher , 
set ALTITUDE of the SERVICE item in the OPTION menu to HIGH  (
57). 
Otherwise, set it to NORMAL. If the projector is used with a wrong setting, it may 
cause damage to the projector itself or the parts inside.  a  Screen size (diagonal) 
 b  Projection distance (±10%, from the projector’s end)
c1 , c2  Screen height (±10%)
• The screen position may shift after installation if the projector is 
suspended from the ceiling or other location due to the flexibility of the plastic 
projector body. If readjustment is necessary, consult with your dealer or service 
personnel.
NOTE 
						

							8
Setting up
Arrangement (continued)
WARNING
(continued on next page)►Install the projector where you can access the power 
outlet easily. If an abnormality should occur, unplug the projector urgently. 
Otherwise it could cause a fire or electric shock.
►Do not subject the projector to unstable conditions.  If the projector falls 
or topples over, it could result in injury or damage to the projector and the 
surrounding things. Using a damaged projector could result in a fire and an 
electric shock.
• 
 Do not place the projector in unstable places, such as an inclined surface, 
places subject to vibration, on top of a wobbly table or cart, or a surface that is 
smaller than the projector.
• 
 Do not put the projector on its side, front or rear position.
• 
 Do not attach nor place anything on the projector unless otherwise specified in 
the manual.
• 
 Do not use any mounting accessories except the accessories specified by the 
manufacturer. Read and keep the manuals of the accessories used.
• 
 For special installation such as ceiling mounting, be sure to consult your dealer 
beforehand.
►
Do not install the projector near thermally conductive or flammable 
things. Such things when heated by the projector could result in a fire and burns.
•  Do not place the projector on a metal stand.
►Do not place the projector where any oils, such as cooking or machine 
oil, are used.  Oil may harm the product, resulting in malfunction, or falling from 
the mounted position.
►Do not place the projector in a place where it may get wet.  Getting the 
projector wet or inserting liquid into the projector could cause a fire and an 
electric shock, and damage the projector.
• 
 Do not place the projector near water, such as in a bathroom, kitchen, or 
poolside.
• 
 Do not place the projector outdoors or by the window.
• 
 Do not place anything containing liquid near the projector. 
						

							9
Setting up
Arrangement (continued)
►Place the projector in a cool place with sufficient 
ventilation.  The projector may shutdown automatically or may malfunction if its 
internal temperature is too high.
Using a damaged projector could result in a fire and an electric shock.
• 
 Do not place the 

projector in direct sunlight or near hot objects such as heaters. 
• 
 Do not place the projector where the air from an air conditioner or similar unit 
will blow on it directly.
• 
 Keep a space of 30 cm or more between a side of the projector and other 
objects such as walls.
• 
 Do not place the projector on carpet, cushions or bedding.
• 
 Do not stop up, block nor cover the projector's vent holes. Do not place 
anything around the projector that could be sucked in or stuck to the projector's 
intake vents.
• 
 Do not place the projector at places that are exposed to magnetic fields, doing 
so can cause the cooling fans inside the projector to malfunction.
►Avoid placing the projector in smoky, humid or dusty place.  Placing the 
projector in such places could cause a fire, an electric shock and malfunction of 
the projector

.
• 
 Do not place the projector near humidifiers. Especially for an ultrasonic 
humidifier, chlorine and minerals contained in tap water are atomized and could 
be deposited in the projector causing image degradation or other problems. • 
 Do not place the projector in a smoking area, kitchen, passageway 
or by the window.
• Position the projector to prevent light from directly hitting the projector's remote 
sensor.
• Do not place the product in a place where radio interference may be caused.
• Check and correct the setting for AL

TITUDE of SERVICE in the OPTION menu 
according to the usage environment  (
57). If the projector is used with a wrong 
setting, it may cause damage to the projector itself or the parts inside.
• Keep heat-sensitive things away from the projector. Otherwise, they may be 
damaged by the heat from the projector. CAUTION
NO
TICE 
						

							10
Setting up
Connecting with your devices
Before connecting the projector to a device, consult the manual of the device to 
confirm that the device is suitable for connecting with this projector and prepare 
the required accessories, such as a cable in accord with the signal of the device. 
Consult your dealer when the required accessory did not come with the product or 
the accessory is damaged.
After making sure that the projector and the devices are turned off, perform 
the connection, according to the following instructions. Refer to the figures in 
subsequent pages.
►Use only the appropriate accessories. Otherwise it could 
cause a fire or damage the projector and devices. 
• 
 Use only the accessories specified or recommended by the projector ’s 
manufacturer. It may be regulated under some standard.
• 
 Neither disassemble nor modify the projector and the accessories.
• 
 Do not use the damaged accessory. Be careful not to damage the accessories. 
Route a cable so that it is neither stepped on nor pinched out. WARNING
►For a cable with a core at only one end, connect the end 
with the core to the projector. That may be required by EMI regulations. CAUTION
• Do not turn on or off the projector while connected to a device in 
operation, unless that is directed in the manual of the device. Otherwise it may 
cause malfunction in the device or projector.
• The function of some input ports can be selected according to your usage 
requirements. Check the reference page indicated beside each port in the 
following illustration.
• Be careful not to mistakenly connect a connector to a wrong port. Otherwise it 
may cause malfunction in the device or projector.
- 
 When connecting a connector to a port, make sure that the shape of the 
connector fits the port.
- 
 Tighten the screws to connect a connector equipped with screws to a port.
- 
 Use the cables with straight plugs, not L-shaped ones, as the input ports of 
the projector are recessed.
NOTE
(continued on next page)