Dukane Projector 8933W User Manual

							21
1.Press INPUT button on the projector. 
Each time you press the button, the projector switches its 
input port from the current port as below.
Selecting an input signal
●  While ON is selected for AUTO SEARCH item in OPTION menu (53), the 
projector will keep checking the ports in above order repeatedly till an input 
signal is detected.
1.Press VIDEO button on the remote control. 
Each time you press the button, the projector switches its 
input port from the current port as below.
●  While ON is selected for AUTO SEARCH item in OPTION menu,  the projector will keep checking every port sequentially till an input signal 
is detected (
53). If  VIDEO button is pressed when  COMPUTER IN1 or 
COMPUTER IN2 port is selected, the projector will check  HDMI port fi rst.
VIDEO button
VIDEODOC.CAMERA
KEYSTONE
ASPECT
SEARCHBLANK
MUTEMY BUTTON
POSITION
ESC MENU
RESET
COMPUTER MY SOURCE/
AUTOMAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
ー
＋VOLUME
1 2
ENTER
1.Press COMPUTER button on the remote control. 
Each time you press the button, the projector switches its 
input port from the current port as below.
●  While ON is selected for AUTO SEARCH item in OPTION menu, the 
projector will keep checking every port sequentially till an input signal is 
detected (
53). If  COMPUTER button is pressed when  VIDEO or HDMI port 
is selected, the projector will check  COMPUTER IN1 port fi rst.
COMPUTER button
VIDEODOC.CAMERA
KEYSTONE
ASPECT
SEARCHBLANK
MUTEMY BUTTON
POSITION
ESC MENU
RESET
COMPUTER MY SOURCE/
AUTOMAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
ー
＋VOLUME
1 2
ENTER
         COMPUTER IN1  COMPUTER IN2 
                         
VIDEO  HDMI
        HDMI 
 VIDEO
      COMPUTER IN1  COMPUTER IN2 
Operating
INPUT 
button 
						

							22
VIDEODOC.CAMERA
KEYSTONE
ASPECTSEARCHBLANK
MUTEMY BUTTON
POSITION
ESC MENU
RESET
COMPUTER MY SOURCE/
AUTOMAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
ー
＋VOLUME
1 2
ENTER
MY SOURCE / 
DOC. CAMERA button
1.Press the MY SOURCE / DOC. CAMERA button on 
the remote control. The input signal will be changed 
into the signal you set as MY SOURCE (
57).
●  This function also can use for document camera. Select the  input port that connected the document camera.
Operating
1.Press SEARCH  button on the remote control.
The projector will start to check its input ports as below in 
order to fi nd any input signals.
When input signal is detected, the projector will stop 
searching and display the image. If no signal is found, 
the projector will return to the state selected before the 
operation.
Searching an input signal
●  While ON is selected for AUTO SEARCH item in OPTION menu (53), the 
projector will keep checking the ports in above order repeatedly till an input 
signal is detected.
SEARCH  button
VIDEODOC.CAMERA
KEYSTONE
ASPECT
SEARCHBLANK
MUTE
MY BUTTON
POSITION ESC MENU
RESET
COMPUTER MY SOURCE/
AUTOMAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
ー
＋VOLUME
1 2
ENTER
Selecting an input signal(continued)
         COMPUTER IN1  COMPUTER IN2 
                         
VIDEO  HDMI 
						

							23
Operating
Selecting an aspect ratio
● ASPECT button does not work when no proper signal is inputted.
● NORMAL mode keeps the original aspect ratio setting.
●  The display will be dark for a split second while switching the Aspect, but this is not a malfunction.
  For a computer signal
CP-EX250/CP-EX300
 NORMAL   4:3   16:9   16:10
        
8933W:
 NORMAL   4:3   16:9   16:10   NATIVE
        
   For a video signal or component video signal
CP-EX250/CP-EX300:
 4:3   16:9   14:9
  
8933W:
 4:3   16:9   16:10   14:9  NATIVE
  For no signal  CP-EX250/CP-EX300 : 4:3 (fi xed)
8933W : 16:10 (fi xed)
1.Press ASPECT button on the remote control.  
Each time you press the button, the projector switches the 
mode for aspect ratio in turn. ASPECT button
  For an HDMITM signal
CP-EX250/CP-EX300
 NORMAL   4:3   16:9   16:10   14:9
8933W:
 NORMAL   4:3   16:9   16:10   14:9   NATIVE
VIDEODOC.CAMERA
KEYSTONE
ASPECT
SEARCHBLANK
MUTE
MY BUTTON
POSITION ESC MENU
RESET
COMPUTER MY SOURCE/
AUTOMAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
ー
＋VOLUME
1 2
ENTER 
						

							24
Operating
1.Use the ZOOM ring to adjust the screen size.
2.Use the FOCUS ring to focus the picture.
Adjusting the zoom and focus
►Do not handle the 
elevator button without holding the projector, 
since the projector may drop down.
 
►Do not tilt the projector other than 
elevating its front within 12 degrees using 
the elevator foot. A tilt of the projector 
exceeding the restriction could cause 
malfunction or shortening the lifetime of 
consumables, or the projector itself. CAUTION

Using the Front elevator foot can tilt the projector in order to project at a suitable 
angle to the screen, elevating the front side of the projector within 12 degrees. 
The elevator foot is adjustable while pushing the elevator button.
1.  Holding the projector, push the elevator 
button to loose the elevator foot.
2.  Release the elevator button in order to 
lock the elevator foot.
3. 
 If necessary, the elevator foot can be manually 
twisted to make more precise adjustments. 
Hold the projector when twisting the foot.

When  the  place 
to  put  the  projector  is  slightly  uneven  to  the  left  or  right,  use  the 
Rear  elevator  foot  to  place  the  projector  horizontally. 
A  spacer  is  installed  on  the 
Rear  elevator  foot  at  the  time  of  shipment,  and  the  projector  is  ready  for  use.  If 
necessary,  detach  the  spacer,  and  the  elevator  foot  can  be  manually  twisted  to 
make more precise adjustments.
Adjusting the projector’s elevator
12°
Front foot
Rear foot
Elevator button
►Keep the spacer away from children and pets. Be careful not 
to let them swallow the spacer. If swallowed consult a physician immediately for 
emergency treatment. WARNING
• After the foot is adjusted, it is possible to return it to the state of the shipment 
with a spacer. 
It is recommended to keep the spacer and reuse it when relocating 
the projector.
NOTE
FOCUS ring
ZOOM ring 
						

							25
Operating
1.Press POSITION button on the remote control when no menu is 
indicated.
The “POSITION” indication will appear on the screen.
Adjusting the position
2.Use the ▲/▼/◄/► cursor buttons to adjust the picture position.
When you want to reset the operation, press  RESET button on 
the remote control during the operation.
To complete this operation, press  POSITION button again. Even if 
you do not do anything, the dialog will automatically disappear 
after a few seconds.
●  
When this function is performed on a video signal, some image such as an extra-
line may appear at outside of the picture.
●  When this function is performed on a video signal, the range of this adjustment  depends on OVER SCAN in IMAGE menu (
37) setting. It is not possible to 
adjust when OVER SCAN is set to 10.
●  If POSITION button is pressed when a menu is indicated on screen, the displayed  picture does not move its position but the menu does.
●  This function is unavailable for signal from the  HDMI port.
1.Press AUTO button on the remote control. 
Pressing this button performs the following.
Using the automatic adjustment feature
  For a computer signal
The vertical position, the horizontal position and the horizontal 
phase will be automatically adjusted. 
Make sure that the application window is set to its maximum size 
prior to attempting to use this feature. A dark picture may still be 
incorrectly adjusted. Use a bright picture when adjusting.
   For a video signal
The video format best suited for the respective input signal will be selected 
automatically. This function is available only when the AUTO is selected for 
the VIDEO FORMAT item in the INPUT menu (
40). The vertical position and 
horizontal position will be automatically set to the default.
●  The automatic adjustment operation requires approx. 10 seconds. Also please  note that it may not function correctly with some input. 
●  When this function is performed for a video signal, a certain extra such as a line  may appear outside a picture.
●  When this function is performed for a computer signal, a black frame may be  displayed on the edge of the screen, depending on the computer model. 
●  
The items adjusted by this function may vary when the FINE or DISABLE is selected 
for the AUTO ADJUST item of the SERVICE item in the OPTION menu (
58).
POSITION  button
VIDEODOC.CAMERA
KEYSTONE
ASPECT
SEARCHBLANK
MUTE
MY BUTTON
POSITION ESC MENU
RESET
COMPUTER MY SOURCE/
AUTOMAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
ー
＋VOLUME
1 2
ENTER
AUTO button
  
For a component video signal 
The vertical position and horizontal position will be automatically set to the default. 
The horizontal phase will be automatically adjusted.
VIDEODOC.CAMERA
KEYSTONE
ASPECT
SEARCHBLANK
MUTE
MY BUTTON
POSITION ESC MENU
RESET
COMPUTER MY SOURCE/
AUTOMAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
ー
＋VOLUME
1 2
ENTER 
						

							26
Operating
1.Press KEYSTONE button on the remote 
control. A dialog will appear on the screen 
to aid you in correcting the distortion.
Correcting the keystone distortions
2.Use the ◄/► buttons for adjustment.
To close the dialog and complete this operation, press 
KEYSTONE button again. Even if you do not do anything, the 
dialog will automatically disappear after ten seconds.
●  The menu or dialog will automatically disappear after several seconds of inactivity. Pressing the KEYSTONE button again fi nishes the operation and 
closes the menu or dialog.
●  The adjustable range of this function will vary among inputs. For some input,  this function may not work well.
●  When REAR / CEILING or FRONT / CEILING is selected for the  INSTALLATION item in the SETUP menu, the automatic vertical keystone 
correction function may not work correctly if the projector screen is slanted or 
tilted downwards.
●  When the zoom adjustment is set to the TELE (telephoto focus), this function  may be excessive. This function should be used when the zoom adjustment is 
set to the full WIDE (wide-angle focus) whenever possible.
●  When the projector is inclined to near ±30 degree or over, this function may  not work well.
●  The display will be dark for a split second while switching the KEYSTONE,  but this is not a malfunction.
KEYSTONE button
VIDEODOC.CAMERA
KEYSTONE
ASPECT SEARCHBLANK
MUTE
MY BUTTON
POSITION ESC MENU
RESET
COMPUTER MY SOURCE/
AUTOMAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
ー
＋VOLUME
1 2
ENTER 
						

							27
Operating
1.
Using the magnify feature
2.
MAGNIFY
ON/OFF button
VIDEODOC.CAMERA
KEYSTONE
ASPECT
SEARCHBLANK
MUTE
MY BUTTON
POSITION ESC MENU
RESET
COMPUTER MY SOURCE/
AUTOMAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
ー
＋VOLUME
1 2
ENTER
3.
4.
Press the MAGNIFY ON button on the remote control. 
The picture will be magnifi ed, and the MAGNIFY dialog 
will appear on the screen. When the 
MAGNIFY 
ON button is pressed for the fi rst time after the 
projector is turned on, the picture will be zoomed 
by 1.5 times. On the dialog, triangle marks to show 
each direction will be displayed.
The display magnifi cation of the projector switches in order with every press 
of the MAGNIFY ON button.
  For computer signals or HDMI
TM (RGB) signals
 1.5  times  2 times  3 times  4 times  1 time
  For video signals, component video signals or HDMITM (Component) 
signals
 1.5  times  2 times  1 time
While the triangles are displayed on the dialog, use the ▲/▼/◄/► cursor
buttons to shift the magnifying area.
Press the MAGNIFY OFF  button on the remote control to exit magnifi cation.
●  The MAGNIFY dialog will automatically disappear in several seconds with no 
operation. The dialog will appear again if the  MAGNIFY ON button is pressed 
when the dialog has automatically disappeared.
●  The magnifi cation is automatically disabled when the displaying signal or its  display condition is changed.
●  While the magnifi cation is active, the keystone distortion condition may vary.  It will be restored when the magnifi cation is disabled.
●  Some horizontal stripes might be visible on the image while magnifi cation is  active.
●  This function is not available in the following cases:  -  A sync signal in the range not supported is input.
-  There is no input signal. 
						

							28
1.Press BLANK button on the remote control.  
The BLANK screen will be displayed instead of the screen of 
input signal. Please refer to BLANK item in SCREEN menu 
(
47).
To exit from the BLANK screen and return to the input signal 
screen, press BLANK button again. 
Temporarily blanking the screen
●  The projector automatically exits from the BLANK mode when 
some control buttons are pressed.
• The sound is not connected with the BLANK screen function. If 
necessary, set the volume or mute first. To display the BLANK screen and mute 
the sound at one time, use AV MUTE function 
(57).
NOTE
1.Press the FREEZE button on the remote control.  
The “FREEZE” indication will appear on the screen (however, 
the indication will not appear when the OFF is selected for 
the MESSAGE item in the SCREEN menu (
49)), and the 
projector will go into the FREEZE mode, which the picture is 
frozen.
To exit the FREEZE mode and restore the screen to normal, 
press the FREEZE button again. 
Temporarily freezing the screen
●  The projector automatically exits from the FREEZE mode when some control 
buttons are pressed.
● 
 If the projector continues projecting a still image for a long time, the LCD 
panel might possibly be burned in. Do not leave the projector in the FREEZE 
mode for too long.
● 
 Images might appear degraded when this function is operated, but it is not a 
malfunction.
FREEZE button
VIDEODOC.CAMERA
KEYSTONE
ASPECT SEARCHBLANK
MUTE
MY BUTTON
POSITION ESC MENU
RESET
COMPUTER MY SOURCE/
AUTOMAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
o
9×VOLUME
 
ENTER
BLANK button
VIDEODOC.CAMERA
KEYSTONE
ASPECT
SEARCHBLANK
MUTE
MY BUTTON
POSITION ESC MENU
RESET
COMPUTER MY SOURCE/
AUTOMAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
o
9×VOLUME
 
ENTER
►If you wish to have a blank screen while the projector's lamp 
is on, use the BLANK function above.
Taking any other action may cause the damage on the projector. CAUTION
Operating 
						

							29
Operating
1.To start the MENU, press the MENU button. The MENU you last used (EASY 
or ADVANCED) will appear. EASY MENU has priority to appear just after 
powered on.
Using the menu function
2.(1)  Use the ▲/▼ cursor buttons to select an item to 
operate. If you want to change it to the ADVANCED 
MENU, select the ADV
ANCED MENU.
(2) 
 Use the ◄/► cursor buttons to operate the item.
This projector has the following menus:  
PICTURE, IMAGE, INPUT, SETUP, AUDIO, SCREEN, OPTION, SECURITY

 and 
EASY MENU.  
EASY MENU consists of functions often used, and the other menus are classified 
into each purpose and brought together as the ADVANCED MENU.
Each of these menus is operated using the same methods. While the projector 
is displaying any menu, the  MENU button on the projector works as the cursor 
buttons. The basic operations of these menus are as follows.
In the EASY MENU
(continued on next page) (1) 
 Use the ▲/▼ cursor buttons to select a menu. 
If you wan

t to change it to the EASY MENU, select 
the EASY MENU. 
The items in the menu appear on the right side.
(2) 
 Press the ► cursor button or ENTER button to  
move the cursor to the right side. Then use the  
▲/▼ cursor buttons to select an item to operate and press the ► cursor 
button or 

ENTER button to progress. The operation menu or dialog of the 
selected item will appear.
(3) 
 Use the buttons as instructed in the OSD to operate the item.
In the ADVANCED MENU
VIDEODOC.CAMERA
KEYSTONEASPECT SEARCHBLANK
MUTEMY BUTTONPOSITION ESC MENU
RESET
COMPUTER MY SOURCE/AUTOMAGNIFYPAGEDOWNONOFFFREEZEUPー＋VOLUME1 2ENTER
POSITION
ESC MENU
RESET
ENTER
POSITION  button
ENTER button
ESC button
MENU button (Cursor buttons)
Cursor buttons
RESET button 
						

							30
Using the menu function (continued)
3.To close the MENU, press the MENU button again or select EXIT and press 
the ◄ cursor button or ENTER button. Even if you do not do anything, the 
dialog will automatically disappear after about 30 seconds.
●  If you want to move the menu position, use the cursor buttons after pressing 
the POSITION  button.
● 
 Some functions cannot be performed when a certain input port is selected, 
or when a certain input signal is displayed.
● 
 When you want to reset the operation, press  RESET button on the remote 
control during the operation. Note that some items (ex. LANGUAGE, 
VOLUME) cannot be reset.
● 
 In the ADVANCED MENU, when you want to return to the previous display, 
press the ◄ cursor button or 

ESC button on the remote control.
Indication in OSD (On Screen Display)
The meanings of the general words on the OSD are as follows.
Indication Meaning
EXITSelecting this word finishes the OSD menu. It's the same as 
pressing the 
MENU button.
RETURN Selecting this word returns the menu to the previous menu.
CANCEL or NO Selecting this word cancels the operation in the present 
menu and returns to the previous menu.
OK or YES Selecting this word executes the prepared function or shifts 
the menu to the next menu.
Operating