Dukane Imagepro 9115 Liquid Crystal Projector Users Manual Manual

							ENGLISH-10ENGLISH-10
O O O O
P P P P
E E E E
R R R R
A A A A
T T T T
I I I I
O O O O
N N N N
S S S S
       
( ( ( (
c c c c
o o o o
n n n n
t t t t
i i i i
n n n n
u u u u
e e e e
d d d d
) ) ) )
Basic Operation
The basic operations shown in Table 3 is performed from the supplied remote control transmitter or
the projector control panel. Items indicated by (*) may be used from the control panel.
Table 3 . Basic Operation
ItemDescription
INPUT
SELECT (
*)
Select RGB Input : Press the RGB button.VIDEO/S-VIDEO/COMPONENT VIDEO →RGB IN 1/RGB IN 2/DVI
RGB IN 1 →RGB IN 2 →DVI (→RGB IN 1)
Select Video Input :Press the VIDEO button.RGB IN 1/RGB IN 2/DVI →VIDEO/S-VIDEO/COMPONENT VIDEO
VIDEO →S-VIDEO →COMPONENT VIDEO (→VIDEO)
• The selected signal name is displayed for approximately 3 seconds when the input
signal is changed.
POSITION
Set/Clear Position Adjustment Mode :Press the POSITION button.The [ ] icon is displayed in the POSITION mode.
Image Position Adjustment:Press the  , , and  buttons in the
POSITION mode.
• Valid only in the MAGNIFY mode with a video signal is input.
• After approximately 10 seconds of inactivity the [ ] icon is extinguished and the
POSITION mode is cleared automatically.
• , , and 
buttons may operate as the mouse control button. Refer to page 4.
RESET (*)
Initialise Each Item :Select an item and press the RESET button.
Initialise Position Adjustment :Press the RESET button and the
POSITION mode. This function is valid only when RGB signal is input.
• Valid except for the VOLUME, LANGUAGE, WHISPER and H PHASE.
• The RESET button may operate as the mouse control button. Refer to page 4.
MAGNIFY
Set MAGNIFY Mode : Press the MAGNIFY  button.
Move Magnified Area :Run the POSITION in the MAGNIFY mode.
Adjust Magnification :Press the MAGNIFY  /  button in MAGNIFY
mode.
Clear MAGNIFY Mode :Press the MAGNIFY  button.
• The MAGNIFY mode is cleared by running or setting the AUTO, ASPECT, INPUT
SELECT or VIDEO, or by changing the input signal.
OFF
FREEZE
Set/Clear FREEZE Mode :Press the FREEZE button. The [II] icon is
displayed, and the image frozen, in the FREEZE mode.
• The FREEZE mode is cleared by running or setting POSITION, VOLUME, MUTE,
Automatic Adjustment, BLANK ON/OFF, or MENU ON/OFF, KEYSTONE, or by
changing the input signal.
• Do not forget to clear frozen static images.
• Use the remote control transmitter at a distance of approximately 5m from the sensor on
the front of the projector, and within a range of 30° left-right. Strong light and obstacles will
interfere with operation of the remote control transmitter.NOTE
$1498
 
 
 
 1.
 
 
						

							ItemDescription
VOLUMEVolume Adjustment :Press the VOLUME / button.
MUTESet/Clear Mute Mode :Press the MUTE button. No sound is heard in the
MUTE mode.
AUTO
Automatic Adjustment at RGB Input :Press the AUTO button. Horizontal
position(H.POSIT), vertical position (V.POSIT),clock phase (H.PHASE), and
horizontal size(H.SIZE) are automatically adjusted. Use with the window at
maximum size in the application display.
Automatic Adjustment at Video Input :Press the AUTO button. A signal
type appropriate for the input signal is selected automatically. Valid only
when AUTO is set for VIDEO on the menu.
• This operation requires approximately 10 seconds. It may not function correctly with
some input signals.
BLANK
ON/OFFSet/Clear Blank Mode:Press the BLANK button. No image is displayed in
the Blank mode. The screen color is as set in BLANK on the Image menu.
MENU
ON/OFFMenu Display Start/Stop:Press the MENU button.• The menu display is terminated automatically after approximately 10 seconds of
inactivity.
MENU
SELECT
Select Menu Type:Press the MENU SELECT button. Allows the user to
select the normal menu or the single menu. Only the selected item is
displayed on the single menu, and other items are displayed with the 
and  buttons as with the normal menu.
• Valid only when the Setup menu is used. Push the MENU SELECT button after
selecting items such as BRIGHTNESS.
• The MENU SELECT button may operate as the mouse control button. Refer to
page 4.
Normal menu Single menu
P.IN P.
MODESelect Mode of P.IN P. Display :Press the PinP button.
Small
→Large→P.IN P.off (→Small)
• Valid only at RGB IN 1, RGB IN 2 or DVI input.
KEYSTONE
Set / Clear KEYSTONE Mode :Press the KEYSTONE  button.
Select KEYSTONE Mode :Press the  /  button in the KEYSTONE
mode.  Vertical 
↔Horizontal
Adjust KEYSTONE :Press the / button.
ENGLISH-11
ENGLISH
ENGLISH-11
O O O O
P P P P
E E E E
R R R R
A A A A
T T T T
I I I I
O O O O
N N N N
S S S S
       
( ( ( (
c c c c
o o o o
n n n n
t t t t
i i i i
n n n n
u u u u
e e e e
d d d d
) ) ) )
Items indicated by (*) may be used from the control panel.
Table 3. Basic Operation (continued)
CONTRAST-2
BRIGHT
CONTRAST
V POSIT
H POSIT
H PHASE
H SIZE
COLOR BAL R
COLOR BAL B
ASPECT0
-2
+1 
0
0 100
100
800SETUP INPUT OPT.IMAGE(MENU SELECT)
$1498
 
 
 
 1.
 
 
						

							ENGLISH-12ENGLISH-12
O O O O
P P P P
E E E E
R R R R
A A A A
T T T T
I I I I
O O O O
N N N N
S S S S
       
( ( ( (
c c c c
o o o o
n n n n
t t t t
i i i i
n n n n
u u u u
e e e e
d d d d
) ) ) )
Setup MenuThe following adjustments and settings are possible
when SETUP is selected at the top of the menu. Part
of the Setup menu differs between RGB input and
video input. Select an item with the  and
buttons, and start operation. Use the Single menu to
reduce menu size (see Table 3, MENU SELECT).
Table 4. Setup Menu
VIDEO
S-VIDEO
COMPONENT VIDEO RGB IN 1
RGB IN 2
DIGITAL
BRIGHT
CONTRAST
V POSIT
H POSIT
H PHASE
H SIZE
COLOR BAL R
COLOR BAL B
ASPECT0
-2
+1 
0
0 100
100
800SETUP INPUT OPT.IMAGEBRIGHT
CONTRAST
SHARPNESS
COLOR
TINT
H PHASE
COLOR BAL  R
COLOR BAL  B
ASPECT0
+1
+1
0
0
0
0SETUP INPUT OPT.IMAGE
ItemDescriptionRGB IN 1
RGB IN 2DIGTALVIDEOS-VIDEOCOMPONENT
BRIGHTAdjustment: Dark ↔Light ✔✔✔
CONTRASTAdjustment:Weak ↔Strong ✔✔✔
V POSITAdjustment:Down ↔Up ✔--
H POSITAdjustment:Left ↔Right ✔--
H PHASEAdjustment:Left ↔Right 
• Adjust to eliminate flicker.✔-✔
H SIZE
Adjustment:Small ↔Large • The image may not be displayed correctly if the horizontal
size is excessive. In such cases, press the RESET button,
and initialize the horizontal size.✔--
SHARPNESSAdjustment:Soft ↔Clear --✔
COLORAdjustment:Light ↔Dark --✔
TINTAdjustment:Red ↔Green • Valid only when NTSC or NTSC 4.43 signal is received.--✔
COLOR BAL RAdjustment:Light ↔Dark ✔✔✔
COLOR BAL BAdjustment:Light ↔Dark ✔✔✔
ASPECT
Select Image Aspect Ratio :
Full [ ] 
↔16:9[ ]  ↔Real [ ]
Select Position of Image:
Press the  button while 16:9[ ] is selected.
Center
→Down →Up (→Center )
✔✔-
Select Image Aspect Ratio:
4:3[ ] 
↔16:9[ ] ↔4:3 small[ ]
Select Position of Image :
Press the  button while 16:9[ ] / 4:3 small[ ]
is selected.
Center
→Down→Up (→Center )• 4:3 small may not be displayed correctly with some input
signals.
--✔
$1498
 
 
 
 1.
 
 
						

							ENGLISH-13
ENGLISH
ENGLISH-13
O O O O
P P P P
E E E E
R R R R
A A A A
T T T T
I I I I
O O O O
N N N N
S S S S
       
( ( ( (
c c c c
o o o o
n n n n
t t t t
i i i i
n n n n
u u u u
e e e e
d d d d
) ) ) )
Input MenuThe following functions are available when INPUT is selected on the
menu. Select an item with the and buttons, and start or stop
operation with the and buttons. The function indicated (**) are
effective on video input mode only, not on RGB input mode, except in
the P.IN P. window on RGB input mode.
Table 5. Input Menu
EXECUTE
CANCELAUTO
RGB
VIDEO
Progressive
BLACK
HDTV SETUP INPUT OPT.IMAGE
ItemDescription
AUTO
Automatic Adjustment at RGB Input: Select the EXECUTE with the
button.Horizontal position (H.POSIT), vertical position (V.POSIT), clock
phase (H.PHASE), and horizontal size (H.SIZE) are automatically adjusted.
Use with the window at maximum size in the application display.
Automatic Adjustment at Video Input: Select the 
EXECUTEwith the 
button. A signal type appropriate for the input signal is selected
automatically when 
EXECUTEis selected automatically. Valid only when
AUTO is set for VIDEO on the menu.
• This operation requires approximately 10 seconds. It may not function correctly with
some input signals. Pressing the AUTO button in this case may correct this problem.
• This function is the same as for the AUTO function in Basic operation.
RGB
Displays RGB Input Frequency:Displays the horizontal and vertical sync
signal frequencies for RGB input.
• Valid only at RGB input.
VIDEO (**)
Select Video Signal Type:Select the signal type with the  and 
buttons. Select NTSC, PAL, SECAM, NTSC4.43, M-PAL, or N-PAL as
appropriate for the input signal. The selection of AUTO enables and
executes the function AUTO (Automatic Adjustment at Video Input), except
for the N-PAL input.
• Use this function when the image becomes unstable (eg. the image becomes
irregular, or lacks color) at VIDEO/S-VIDEO input.
• Automatic Adjustment requires approximately 10 seconds. It may not function
correctly with some input signals. Pressing the AUTO button in this case may correct
this problem except for the N-PAL input.
• For the COMPONENT VIDEO input, this function is not effective and the signal type
is distinguished automatically. Refer to the item HDTV of the OPT. Menu for the
signal of HDTV.
BLACK (**)
Set/Clear Black Enhancement Mode:Select the TURN ON / TURN OFF
with the  /  button. When the TURN ON is selected, the black
enhancement mode is active and the contrast ratio of the screen for the
video input will be raised by making black level darker.
Progressive
(**)
Select Progressive Mode:Select the mode suitable for the input signal
with the  and  buttons. The TV mode and the FILM mode convert the
interlaced video signal into the progressive signal. The FILM mode is
adptable 2-3 Pull-Down system to the conversion.
• Use this function to raise resolution, at the interlaced video input except HDTV
signal.
HDTVSelect HDTV mode:Select the 1035i mode or 1080i mode suitable for the
input signal with the  /  button.
$1498
 
 
 
 1.
 
 
						

							ENGLISH-14ENGLISH-14
O O O O
P P P P
E E E E
R R R R
A A A A
T T T T
I I I I
O O O O
N N N N
S S S S
       
( ( ( (
c c c c
o o o o
n n n n
t t t t
i i i i
n n n n
u u u u
e e e e
d d d d
) ) ) )
Image Menu
The following adjustments and settings are available when IMAGE is
selected on the menu. Select an item with the and buttons, and 
start or stop operation with the and buttons.
Table 6. Image Menu
BLANK
MIRROR
START UP
P. IN P.POSITP.IN P.INPUT
GAMMA SETUP INPUT OPT.
IMAGE
ItemDescription
BLANKSelect Blank Screen Color:Select color with the  and  buttons.• The image is cleared and the entire screen is displayed in the selected color, when
BLANK mode is set with BLANK ON, or when there is no signal for 5 minutes.
MIRRORSelect Mirror Status:Select mirror status with  and  buttons.
START UP
Setup Initial Screen Display:Select TURN ON with the  button.
Clear Initial Screen Display:Select TURN OFF with the  button.
• Note that if TURN OFF is selected the blank screen is displayed in blue when there
is no signal.
P. IN P.
POSITSelect Position of P. in P. Display :Press the or button.
↔↔↔
• Valid only at RGB IN 1, RGB IN 2 or DVI input.
P. IN P.
INPUTSelect signal of P. in P. Display :Press the or button.
VIDEO 
↔S-VIDEO ↔COMPONENT
GAMMASelect Gamma mode:Select the gamma mode with the  /  button.
NORMAL 
↔CINEMA ↔DYNAMIC
$1498
 
 
 
 1.
 
 
						

							ENGLISH-15
ENGLISH
ENGLISH-15
O O O O
P P P P
E E E E
R R R R
A A A A
T T T T
I I I I
O O O O
N N N N
S S S S
       
( ( ( (
c c c c
o o o o
n n n n
t t t t
i i i i
n n n n
u u u u
e e e e
d d d d
) ) ) )
Options Menu
The following adjustments and settings are available when OPT. is
selected on the menu. Select an item with the and buttons, and
start or stop operation with the  and buttons. The function
indicated (**) are effective on video input mode only, not on RGB input
mode, except in the P.IN P. window on RGB input mode.
Table 7. Options Menu
VOLUMEMENU COLORLANGUAGE
AUTO OFF
SYNC ON G
WHISPER
16 SETUP INPUT OPT.IMAGE
ItemDescription
VOLUMEVolume Adjustment:Reduce VOLUME ↔Increase VOLUME 
MENU COLORSelect Menu Background Color:Select with the  and  buttons.
LANGUAGESelect Menu Display Language:Select with the  and  buttons.
AUTO OFF
Set AUTO OFF:Set 1~99 minutes with the  and  buttons. The
system automatically enters the standby mode when a signal is not
received for the set time.
Clear AUTO OFF:Select STOP (0 min.) with the  button. When
STOP is selected the system does not enter the standby mode even if
no signal is received.
SYNC ON G
SYNC ON G Valid:Select TURN ON with the  button.
SYNC ON G Invalid:Select TURN OFF with the  button.
• May not be displayed correctly with some input signals when SYNC ON G is
valid. In such cases, remove the signal connector so that no signal is received,
set SYNC ON G to invalid, and reconnect the signal.
WHISPER
Set / Crear WHISPER Mode: Press the  and  button.When the
WHISPER is selected, the WHISPER mode is active. In the WHISPER
mode, acoustic moise level from the unit is reduced, and brightness
level on screen is a little lower.
$1498
 
 
 
 1.
 
 
						

							ENGLISH-16
O O O O
P P P P
E E E E
R R R R
A A A A
T T T T
I I I I
O O O O
N N N N
S S S S
       
( ( ( (
c c c c
o o o o
n n n n
t t t t
i i i i
n n n n
u u u u
e e e e
d d d d
) ) ) )
No Signal Menu
The same adjustments and settings are available as with the Image and
Options menus when the MENU button is pressed during display of the
“NO INPUT IS DETECTED ON ***” or “SYNC IS OUT OF RANGE
ON ***” message while no signal is received.
Table 8. No Signal Menu
VOLUME
BLANK
MIRROR
START UP
MENU COLORLANGUAGE
AUTO OFF
SYNC ON G
WHISPER
16
ItemDescription
VOLUME
Volume Adjustment:Reduce VOLUME ↔Increase VOLUME • When this function is used, audio input is automatically switched to video. The
audio input can be switched by moving the DISK PAD left and right during the
display of the volume adjustment bar. The volume adjustment bar is displayed by
pressing VOLUME  or VOLUME  button.
BLANK
Select Blank Screen Color:Select the color with the  and  buttons.• The image is cleared and the entire screen is displayed in the selected color,
when BLANK mode is set with BLANK ON, or when there is no signal for 5
minutes.
MIRROROperation Start/Stop:Press the  or  button.
Select Mirror Status:Select the mirror status with the  and 
buttons.
START UP
Operation Start/Stop:Press the  or  button.
Setup Initial Screen Display:Select the TURN ON with the  button.
Clear Initial Screen Display:Select the TURN OFF with the  button.
• Note that if TURN OFF is selected the blank screen is displayed in blue when
there is no signal.
MENU COLORSelect Menu Background Color:Select the color with the  and 
buttons.
LANGUAGE
Operation Start/Stop:Press the  or  button.
Select Menu Display Language:Select the language with the  and
buttons.
AUTO OFF
Operation start/stop:Press the  or  button.
Set AUTO OFF:Set 1~99 minutes with the  and  buttons. The
system automatically enters the standby mode when a signal is not
received for the set time.
Clear AUTO OFF:Select the STOP (0 min.) with the  button. When
the STOP is selected the system does not enter the standby mode even
if no signal is received.
SYNC ON G
Operation Start/Stop:Press the  or  button.
SYNC ON G Valid:Select the TURN ON with the  button.
SYNC ON G Invalid:Select the TURN OFF with the  button.
• May not be displayed correctly with some input signals when the SYNC ON G is
valid. In such cases, remove the signal connector so that no signal is received,
set the SYNC ON G to invalid, and reconnect the signal.
WHISPER
Operation Start/Stop:Press the  or  button.
Set / Crear WHISPER Mode: Press the  and  button.When the
WHISPER is selected, the WHISPER mode is active. In the WHISPER
mode, acoustic moise level from the unit is reduced, and brightness
level on screen is a little lower.
$1498
 
 
 
 1.
 
 
						

							ENGLISH-17
ENGLISH
MAINTENANCE MAINTENANCE
Lamp
HIGH VOLTAGE
HIGH TEMPERATURE
HIGH PRESSURE
Contact your dealer before replacing the lamp.
For the optional lamp, see the item “Optional Parts” of the Table 12.
Before replacing the lamp, switch power OFF, remove the power cord from the power outlet, and
wait approximately 45 minutes until the lamp has cooled. The lamp may explode if handled at high
temperatures.
Lamp Life
Projector lamps have a finite life. The image will become darker, and hues will become weaker,
after a lamp has been used for a long period of time. 
Replace the lamp if the LAMP indicator is red, or the CHANGE THE LAMP message appears
when the projector is switched ON. See Table 9 of P.20 and Table 10 of P.21.
•The LAMP indicator is also red when the lamp unit reaches high temperature. Before
replacing the lamp, switch power OFF, wait approximately 20 minutes, and switch power ON again.
If the LAMP indicator is still red, replace the lamp.NOTE
Lamp
Front
glass Reflector
WARNING• For disposal of used lamp, treat
according to the instruction of community
authorities.
• Since the lamp is made of glass, do not apply shock
to it and do not scratch it.
• Also, do not use old lamp. This could also cause
explosion of the lamp.
• Premature lamp failure MAY be caused by an
electronic component in the projector and not
necessarily the lamp. If unsure contact your local
service center.
• If it is probable that the lamp has exploded (explosive
sound is heard), disconnect the power plug from the
power outlet and ask your dealer to replace lamp. The
lamp is covered by front glass , but, in rare cases, the
reflector and the inside of the projector may be
damaged by scattered broken pieces of glass, and
broken pieces could cause injury when being handled.
• Do not use the projector with the lamp cover removed.
$1498
 
 
 
 1.
 
 
						

							ENGLISH-18ENGLISH-18
M M M M
A A A A
I I I I
N N N N
T T T T
E E E E
N N N N
A A A A
N N N N
C C C C
E E E E
       
( ( ( (
c c c c
o o o o
n n n n
t t t t
i i i i
n n n n
u u u u
e e e e
d d d d
) ) ) )
Replacing the Lamp
1. Switch the projector OFF, remove the power cord from the
power outlet, and wait at least 45 minutes for the unit to cool.
2. Prepare a new lamp.
3. Check that the projector has cooled sufficiently, and gently
turn it upside down.
4. Loosen the two screws as shown in the diagram, and remove
the lamp cover.
5. Loosen the two screws, and gently remove the lamp while
holding the grips. Touching the inside of the lamp case may
result in uneven coloring.
6. Install the new lamp and tighten the two screws firmly. Also
steadily push the opposite side of the screwed lamp into the
unit.
7. Replace the lamp cover in position and tighten the screw
firmly.
8. Gently turn the projector right-side up.
Resetting the Lamp Timer
Reset the lamp timer after replacing the lamp. When the lamp has been replaced after the LAMP
indicator is red, or the CHANGE THE LAMP message is displayed, complete the following
operation within ten minutes of switching power ON. The power will be turned off automatically in
over 10 minutes.
1. Switch power ON, and press the RESET button, for approximately three seconds. The ‘LAMP
xxxx hr’ message will appear on the lamp timer on the bottom of the screen.
2. Press the MENU button on the remote control transmitter, or the RESET button on the control
panel, while the lamp timer is displayed. The ‘LAMP xxxx 
→0 CANCEL’ message will
then appear.
3. Press the  and select 0, and wait until the timer display is cleared.
•Do not reset the lamp timer without replacing the lamp. Reset the lamp timer always
when replacing the lamp. The message functions will not operate  properly if the lamp timer is not
reset correctly.
•An air filter is attached to the optional lamp. Replace the filter after replacing the lamp.
NOTE
CAUTION• Ensure that screws are tightened
properly. Screws not tightened fully may result
in injury or accidents.
• Do not use the projector with the lamp cover
removed.
$1498
 
 
 
 1.
 
 
						

							ENGLISH-19
ENGLISH
ENGLISH-19
M M M M
A A A A
I I I I
N N N N
T T T T
E E E E
N N N N
A A A A
N N N N
C C C C
E E E E
       
( ( ( (
c c c c
o o o o
n n n n
t t t t
i i i i
n n n n
u u u u
e e e e
d d d d
) ) ) )
Air Filter 
Replacing the Air Filter
Replace the air filter if contamination cannot be
removed, or if it is damaged.
1. Remove the filter lid.
2. Pull and remove the old filter from the filter box.
3. Insert the new filter to the filter box. Push left
and right edges of the filter with fingers in order
to fit the filter to the box properly. Check that
there is no gap between the filter and plastics at
top, left and right side edge of the filter.
4. Set the filter lid.
Cleaning the air Filter
The air filter should be cleaned as described below at intervals of approximately 300 hours.
1. Switch the projector power supply OFF, and remove the power cord from the power outlet.
2. Clean the air filter with a vacuum cleaner.
Other Maintenance
Maintenance Inside the Equipment
For safety reasons, ensure that the equipment is cleaned and checked by the dealer once every two
years. Maintaining the equipment by yourself is dangerous.
Cleaning the Lens
Gently wipe the lens with lens cleaning paper. Do not touch the lens with your hands.
Cleaning the Cabinet and Remote control transmitter
Gently wipe with a soft cloth. If dirt and stains etc. are not easily removed, use a soft cloth
dampened with water, or water and a neutral detergent, and wipe dry with a soft, dry cloth.
CAUTION• Switch power OFF and remove the power cord from the power
outlet before beginning maintenance work. Please read the separate “SAFETY
INSTRUCTIONS” thoroughly to ensure that maintenance is performed correctly.
• Do not use detergents or chemicals other than those noted above (e.g. benzene
or thinners).
• Do not use cleaning sprays.
• Do not rub with hard materials, or tap the equipment.
CAUTION• Switch power OFF and remove the power cord from the power
outlet before beginning maintenance work. Please read the separate “SAFETY
INSTRUCTIONS” thoroughly to ensure that maintenance is performed correctly.
• Replace the air filter if contamination cannot be removed, or if it is damaged.
Contact your dealer in such case. For the optional air filter, see the item “Option
Parts” of the Table 12. 
• Do not use the equipment with the air filter removed.
• When the air filter is clogged with dust etc. the power supply is switched OFF
automatically to prevent the temperature rising inside the projector.
CP-SX5500
Filter box
Filter Lid
Filter
$1498
 
 
 
 1.