Dukane Imagepro 8944 Lcd Projector Users Manual

							
49

ItemDescription
SECURITY(continued)
1.3 If you have forgotten your PASSWORD
.3-     Follow the procedure in   .  -   to display the ENTER PASSWORD BOX.
.3-     While the ENTER PASSWORD BOX is displayed, press and hold the RESET button on the remote control for about 3 seconds or press and hold the INPUT and ► buttons on the projector for about 3 seconds.The  0 digit Inquiring Code will be displayed. • If there is no key input for about 55 seconds while the Inquiring Code is displayed the menu will close. If necessary repeat the process from   .3-  .
.3-3   Contact your dealer with the   0 digit Inquiring Code. Your PASSWORD will be sent after your user registration information is confirmed.
2. Using the MyScreen PASSWORD Function
The MyScreen PASSWORD function can be used to prohibit access to the MyScreen function and prevent the currently registered MyScreen image from being overwritten.
2.1 Turning on the MyScreen PASSWORD 
Function
2.1-1  Use the ▲/▼ buttons on the SECURITY menu to select MyScreen PASSWORD and press the ► button to display the MyScreen PASSWORD on/off menu.
2.2 Setting the PASSWORD
.  -     Display the MyScreen on/off menu using the procedure in   .  -  .
2.2-2  Use the ▲/▼ buttons on the MyScreen PASSWORD on/off menu to select TURN ON.The ENTER PASSWORD BOX (small) will be displayed.
2.2-3  Use the ▲/▼/◄/► buttons to enter the PASSWORD. Move the cursor to the right side of the ENTER PASSWORD BOX (small) and press the ► button to display the CHECK PASSWORD BOX, enter the same PASSWORD again.
5%74+6;2#55914&

+PSWKTKPI%QFG
OPTION Menu (continued)
OPTION Menu
/[5ETGGP0642#55914&
0:6

37+6
Inquiring Code (PASSWORD)
/[5ETGGP%*%-2#55914&
0:6

37+6CHECK PASSWORD BOX
/[5ETGGP2#55914&
67401067401((
MyScreen PASSWORD on/off menu
ENTER PASSWORD BOX (small)
(continued on next page) 
						

							
50

ItemDescription
SECURITY(continued)
.  -4   Move the cursor to the right side of the CHECK PASSWORD BOX and press the ► button to display the PASSWORD for about   0 seconds, please make note of the PASSWORD during this time. Pressing the ENTER button on the remote control or INPUT button on the projector will return to MyScreen PASS WORD on/off menu.When a PASSWORD is set for MyScreen:
• The MyScreen registration function (and menu) will be unavailable.
• The MyScreen Lock function (and menu) will be unavailable.
• The START UP setting will be locked on MyScreen (and the menu will be unavailable).Turning the MyScreen PASSWORD off will allow normal operation of both  functions.
• Please do not forget your MyScreen PASSWORD.
2.3 Turning the PASSWORD off
.3-     Follow the procedure in   .  -   to display the MyScreen PASSWORD on/off menu.
.3-     Select TURN OFF to display the ENTER PASSWORD BOX (large). Enter the registered PASSWORD and the screen will return to the MyScreen on/off menu.If an incorrect PASSWORD is input the menu will close. If necessary repeat the process from   .3-  .
2.4 If you have forgotten your PASSWORD
.4-     Follow the procedure in   .  -   to display the MyScreen PASSWORD on/off menu.
.4-     Select TURN OFF to display the ENTER PASSWORD BOX (large). The   0 digit Inquiring Code will be displayed inside the BOX.
.4-3   Contact your dealer with the   0 digit Inquiring Code. Your PASSWORD will be sent after your user registration information is confirmed.
3. Using the PIN LOCK FunctionPIN LOCK is a function which prevents the projector from being used unle\
ss a registered Code is input.3.1 Registering the PIN Code
3.1-1  Use the ▲/▼ buttons on the SECURITY menu to select PIN LOCK and press the ► button or the ENTER button to display the PIN LOCK on/off menu.
3.1-2  Use the ▲/▼ buttons on the PIN LOCK on/off menu to select TURN ON and the PIN BOX will be displayed. 
0:637+6
+PSWKTKPI%QFG         
/[5ETGGP0642#55914&
OPTION Menu (continued)
OPTION Menu
/[5ETGGP%1/2.6
:+6

064
ENTER PASSWORD BOX (large)
PASSWORD BOX
2+0.1%-
67401067401((
PIN LOCK on/off menu
(continued on next page) 
						

							
5

ItemDescription
SECURITY(continued)
3.1-3    Input a 4 part PIN Code using the ▲/▼/◄/►/RGB and INPUT buttons.A CONFIRMATION BOX will appear. Reenter the same PIN Code. This will complete the PIN Code registration.• If there is no key input for about 55 seconds while the PIN BOX or the CONFIRMATION BOX are displayed the menu will close. If necessary repeat the process from 3.  -  .Afterwards, anytime the projector is restarted after the power switch is turned off the PIN BOX will be displayed. Enter the registered PIN Code.The projector can be used after entering the registered PIN Code. If an incorrect PIN Code is input the PIN BOX will be displayed again.If an incorrect PIN Code is input 3 times the projector will turn off. Afterwards the projector will turn off every time an incorrect PIN Code is input. The projector will also turn off if there is no key input for about 5 minutes while the PIN BOX is displayed.This function will activate only when the projector is started after the\
 power switch was turned off.
• Please do not forget your PIN Code.
3.2 Turning Off the PIN LOCK Function
3. -     Follow the procedure in 3.  -   to display the PIN LOCK on/off menu. Use the ▲/▼ buttons to select TURN OFF and the PIN BOX will be displayed.Enter the registered PIN Code to turn the PIN LOCK function off.If an incorrect PASSWORD is entered the  menu will close.
3.3 If you have forgotten your PIN Code
3.3-    While the PIN BOX is displayed, press and hold the RESET button for three seconds or press and hold the INPUT and ► buttons for three seconds. The   0 digit Inquiring Code will be displayed. • If there is no key input for about 5 minutes while the Inquiring Code is displayed the projector will turn off.
3.3-    Contact your dealer with the   0 digit Inquiring Code. Your PASSWORD will be sent after your user registration information is confirmed.
OPTION Menu (continued)
OPTION Menu
PIN BOX
2+0$1:
4)$
+PRWV2+0%QFG
CONFIRMATION BOX(PIN BOX)
2+0$1:
4)$
%QPHKTOCVKQP
2+0$1:

+PSWKTKPI%QFG
Inquiring Code (PIN Code)
(continued on next page) 
						

							
5

ItemDescription
SECURITY(continued)
4. Using the Transition Detector Function
While the Transition Detector function is ON, when power switch is started to supply to the projector, it might react as below.• Transition Detector alarm shown below might appear on screen, if the projector has been moved or re-installed.• Transition Detector alarm might appear on screen, if the MIRROR setting has been changed.• Keystone adjustment feature has been prohibited as long as the Transition Detector function is ON.
4.1 Turning On the Transition Detector Function
4.  -     Use the ▲/▼ buttons on the SECURITY menu to select Transition Detector and press the ► or the ENTER button to display the Transition Detector on/off menu. Select TURN ON and the current angle and mirror setting will be recorded.• This feature may not function properly if the projector is not in a stable position when TURN ON is selected.
4. -     If this function is set to TURN ON when the vertical angle of the projector or mirror setting at which the projector is turned on is different than the previously recorded the Transition Detector Alarm will be displayed and the projector will not display the input signal.
Set the Transition Detector off I the SECURITY menu to display the input signal.If the Transition Detector ALARM is displayed for about 5 minutes the lamp will turn off. This function will activate only when the projector is started after the\
 power switch was turned off.
4.2 Setting the Transition Detector PASSWORD
4.2-1  Use the ▲/▼ buttons on the SECURITY menu to select Transition Detector and press the ► or the ENTER button to display the Transition Detector on/off menu.
4.2-2  Use the ▲/▼ buttons on the Transition Detector on/off menu to select TURN ON. The ENTER PASSWORD BOX (small) will be displayed.
4. -3  Use the ▲/▼/◄/► buttons to enter a PASSWORD. Move the cursor to the right side of the ENTER PASSWORD BOX (small) and press the ► button to display the CHECK PASSWORD BOX, enter the same PASSWORD again.
4. -4   Move the cursor to the right side of the CHECK PASSWORD BOX and press the ► button to display the PASSWORD for about   0 seconds, please make note of the PASSWORD during this time.Pressing the ENTER button on the remote control or the INPUT button on the projector will return to the Transition Detector on/off menu.• Please do not forget your Transition Detector PASSWORD.
OPTION Menu (continued)
OPTION Menu
64#05+6+10&6%614
67401067401((
Transition Detector on/off menu
Transition Detector Alarm
2+0$1:
64#05+6+10&6%61410  6JGRTQLGEVQTJCUDGGPVTCPUHGTTGFHTQORTGXKQWUN[KPUVCNNGFRQUKVKQP+H[QWYKUJVQJCXGCUSWCTGKOCIGQPUETGGPCICKPFKUCDNG6TCPUKVKQP&GVGEVQTQP/GPW
64#05+6+10&6%6140642#55914&
0:6

37+6ENTER PASSWORD BOX (small)64#05+6+10&6%614%*%-2#55914&
0:6

37+6CHECK PASSWORD BOX64#05+6+10&6%614%1/2.6
:+6

064PASSWORD BOX
(continued on next page) 
						

							
53

ItemDescription
SECURITY(continued)
4.3 Setting the Transition Detector off
4.3-    Follow the procedure in 4.  -   to display the Transition Detector on/off menu.
4.3-    Select TURN OFF to display the ENTER PASSWORD BOX (large). Enter the registered PASSWORD and the screen will return to the Transition Detector on/off menu.If an incorrect PASSWORD is input the menu will close. If necessary repeat the process from 4.3-  .
4.4 If you have forgotten your PASSWORD
4.4-    Follow the procedure in 4.  -   to display the Transition Detector on/off menu.
4.4-    Select TURN OFF to display the ENTER PASSWORD BOX (large). The   0 digit Inquiring Code will be displayed inside the BOX.
4.4-3  Contact your dealer with the   0 digit Inquiring Code. Your PASSWORD will be sent after your user registration information is confirmed.
OPTION Menu (continued)
OPTION Menu
0:637+6
+PSWKTKPI%QFG         
64#05+6+10&6%6140642#55914&
ENTER PASSWORD BOX (large) 
						

							
54

(continued on next page)
ItemDescription
LIVE MODE

Selecting this item sets the projector onto the “Live Mode”. On the “Live Mode”, the projector displays the images from the PC \
via Network, supported by “MIU Live Viewer”. ( 1.1 Live Mode of the User’s Manual - Network Functions, last section of this manual).
PC-LESSPRESENTATION
Selecting this item displays the PC-LESS PRESENTATION menu.Using the menu is able to make the projector display the images stored in SD card or USB memory, and realizes a presentation without PC. ( 1.2 PC-LESS Presentation of the User’s Manual - Network Functions)
MIU Menu
/07=4)$?
2+%674
5.%6

+/#)
5672+0276
#7&+1
126+10/+7#5;/07
5%40
.+8/1&2%.5524506#6+105672G5*16+0(14/#6+10548+%
MIU Menu
Consult with your network administrator before connecting 
to an existing access point on your network. Incorrect 
network settings on this projector may cause trouble on the 
network.
Select “MIU” from the main menu to access the following 
functions. 
Select an item using the ▲/▼ cursor buttons on the 
projector or remote control, and press the ► cursor button 
on the projector or remote control, or ENTER button on 
the remote control to execute the item. Then perform it 
according to the following table.
See the User’s Manual - Network Functions for details of 
MIU operation. Last section of this manual.
NOTE  • The factory default setting for DHCP is TURN OFF. If your network 
has DHCP enabled, and needs to set IP ADDRESS, SUBNET MASK and 
DEFAULT GATEWAY automatically, please set DHCP to TURN ON. ( 2.5.2 
Network Settings of the User’s Manual - Network Functions)
• If you are not utilizing SNTP ( 2.5.7 Date/Time Settings of the User’s 
Manual - Network Functions), then you must set the DATE AND TIME (56) 
during the initial installation.
2%.5524506#6+106*7/$0#+.5.+&5*19&+4%64;&+52.#;5+
						

							
55

(continued on next page)
ItemOperation
e-SHOT 
Selecting this item displays the e-SHOT menu.
Use the ▲/▼ buttons to select an item which is a still image by the e-SHOT ( 4.7 e-SHOT (Still Image Transfer) Display of the User’s Manual - Network Functions) and the ► or ENTER button to display the image.
• Insert the SD memory card or USB memory into the projector before you use the e-SHOT function. (12)• The item without image stored cannot be selected.• The image names are each displayed in  6 characters or less.• Japanese file name is displayed correctly only when the projector ’s language is set to Japanese. And the characters other than alphanumeric character are not displayed correctly in Japanese mode. (Ç, ä, et\
c.)
To switch the image displayed 
Use the ▲/▼ buttons.
To return to the menu
Press the ◄ or ESC button on the remote control.
To erase the image displayed and its source file in the SD card or USB memory
( )   Press the RESET button on the remote control while displaying an image to display the e-SHOT - RESET menu. 
( )   Press the ENTER button on the remote control or the INPUT button on the projector to perform to erase. To stop erasing, press the ◄ button and INPUT button on the projector. 
SETUP
Selecting this item displays the MIU SETUP menu.
Use the ▲/▼ buttons to select an item, and the ► or ENTER button on the remote control to perform the item.
DHCP (Dynamic Host Configuration Protocol)
Use the ▲/▼ buttons to turn DHCP on/off.
TURN ON ó TURN OFF
• Select TURN OFF when the network does not have DHCP enabled.
&*%267401067401((
 /+75672&*%210+2#&&45557$06/#5-&(#7.6)#69#;
#0&6+/6+/&+((40%
/1&%*
06914-/1&52&0%4;26+10
MIU Menu
MIU Menu (continued)
G5*16
+/#)+/#)&/10564#6+10
&/10564#6+106#$.
24506#6+10(+.
+/#)+/#)
G5*16456+/#)
01;55%064 
						

							
56

ItemDescription
SETUP(continued)
IP ADDRESS
Use the ▲/▼/◄/► buttons to enter the IP ADDRESS. This function can only be used when DHCP is set to TURN OFF.
• The IP ADDRESS is the number that identifies this projector on the network. You cannot have two devices with the same IP ADDRESS on the same network.
SUBNET MASK
Use the ▲/▼/◄/► buttons to enter the same SUBNET MASK used by your PC. This function can only be used when DHCP is set to TURN OFF.
DEFAULT GATEWAY
Use the ▲/▼/◄/► buttons to enter the DEFAULT GATEWAY (a node on a computer network that serves as an access point to another network) address.This function can only be used when DHCP is set to TURN OFF.
TIME DIFFERENCE
Use the ▲/▼ buttons to enter the TIME DIFFERENCE. Set the same TIME DIFFERENCE as the one set on your PC. If unsure, consult your network administrator. Use the ◄ button to return to the menu after setting the TIME DIFFERENCE.
DATE AND TIME
Use the ▲/▼/◄/► buttons to enter the Year (last two digits), Month, Date, Hour and Minute.
• The projector will override this setting and retrieve DATE AND TIME information from the Timeserver when SNTP is enabled. ( 2.5.7 Date/Time Settings of the User’s Manual - Network Functions)

+2#&&455

255.255.0
SUBNET MASK
255.
6+/&+((40%
:ž:¤:«:w:‡:‡:‘:‡:‡

#0&6+/
0.0.0
DEFAULT GATEWAY
0.
MIU Menu (continued)
MIU Menu
(continued on next page) 
						

							
57

ItemDescription
SETUP(continued)
MODEUse the ▲/▼ buttons to select the mode of the network communication system. Select it according to the setting of your PC.
ADHOC ó INFRASTRUCTURE
CHUse the ▲/▼ buttons to select the channel of the wireless LAN while using it. Select it according to the setting of your PC.The channels   to    are available.• The available channels would be various depending on a country. In addition, wireless LAN card might be required due to the standard.
ENCRYPTIONUse the ▲/▼ buttons to select the encryption method to be used.
WPA -PSK(AES)    ô
WPA-PSK(AES) ó WPA-PSK(TKIP) ó WEP   8bit ó WEP 64bit ó OFF
SPEEDUse the ▲/▼ buttons to select the transfer rate.(M : Mbps : Megabits per second)
AUTOó54Mó48Mó36Mó4Mó8M ô                 ô
MóMó5.5Mó6Mó9Mó Mó M
• The AUTO mode automatically selects the optimum rate.• Transfer rates may change due to the network situation.
NETWORK MODEUse the ▲/▼ buttons to select the network mode.
WIRELESS ó WIRED
• The network mode will be initialized whenever the power is turned on with the power switch.• The WIRELESS will be enabled when the wireless network card is installed.• The WIRED will be enabled when the wireless network card is not installed.
MIU Menu (continued)
MIU Menu
0%4;26+10
92#25-
#5
92DKV92#25-
6-+2
92#25-
#5
1((92DKV
/1&#&*1%+0(4#5647%674
 %*
06914-/1&9+4.559+4&
(continued on next page)
52&
/#761
//
/
//
/
//
//
/ 
						

							
58
MIU Menu
ItemDescription
INFORMATION
Selecting this item displays the MIU-INFORMATION dialog for confirming the network setting.
• Only the first  6 characters of the projector name are displayed.• Only the first 3  characters of the SSID are displayed.• When the voltage level of the battery for the built in clock decrea\
ses, the set time may become incorrect even though accurate date and time are input. Replace the battery suitably. (63)• MAC wireless will not be displayed when the NETWORK MODE is set to \
the WIRED even if the wireless LAN SD card is mounted.• IP ADDRESS, SUBNET MASK and DEFAULT GATEWAY indicate “0.0.0.0” in the following condition.( ) The NETWORK MODE is set to the WIRELESSE and the wireless LAN SD card is not mounted.( ) DHCP is ON and the projector does not get address from DHCP server.
SERVICE
Selecting this item displays the SERVICE menu.Use the ▲/▼ buttons to select an item, and the ► or ENTER button on the remote control to perform the item.
REMOVE ALL, REMOVE SD CARD, REMOVE USBUse the ▲ button to perform the procedure to remove the media.EXECUTE  CANCEL• Before removing the SD card or USB memory, be sure to perform the REMOVE procedure.MIU RESTARTUse the ▲ button to restart the network communication. The network communication will be cut off once and restarted.EXECUTE  CANCEL• After selecting the EXECUTE, the MIU menu may not be controlled approximately   0 seconds.• If DHCP is ON, IP address may be changed.
MIU Menu (continued)
4/18#..:%76%#0%.
0%4;26+1092DKV
+2#&&45557$06/#5-
/+7+0(14/#6+10
&(#7.6)#69#;
0#/
#0&6+/6+/&+((40%)/6
/1&#&*1%%*
124#6+10.+875$//14;5&%#4&9+4.55.#052&/
/#%6*406/#%9+4.55
55+&
06914-/1&9+4.55
   SERVICEREMOVE ALLREMOVE SD CARDREMOVE USBMIU RESTART
   MIU RESTARTEXECUTECANCEL