Dukane Imagepro 8944 Lcd Projector Users Manual



2. Equipment connection and network setting
2.4  Manual network connection setting – For wireless LAN (Continued)
Using wireless LAN utility for Windows XP standard.
Wireless LAN initial settings for the projector is as follows.
Connection Control   : Ad-Hoc
SSID  : wireless
Channel  : 1ch
Encryption rating  : None
Communication speed  : AUTO
IP address  : 192.168.1.10
*  You can change these settings as you want. Use configuration utility or menu to 
change. (Refer to section 2.5)
1)   Open...

18

2. Equipment connection and network setting
2.4  Manual network connection setting – For wireless LAN (Continued)
4)  Set used protocol as “TCP/IP” and open TCP/IP property. Set IP address and 
other settings as same as wired LAN connection set up. (12)
5)  Open “Wireless Networks” tab. (Fig. 2.4.2.c)
Fig. 2.4.2.c “Wireless Network Connection Properties” window (2)
Fig. 2.4.2.d “Wireless network Properties” window
6)  Add check mark for “Use Windows to configure my wireless network settings” 
in...



2. Equipment connection and network setting
2.4  Manual network connection setting – For wireless LAN (Continued)
8)  Set each item as follows. 
Network name (SSID): wireless 
Data encryption: Invalid (Default setting is invalid.)
*  This explanation meets the projector default setting. If access point is used or 
data encryption is used, if needs to change settings properly. Refer to PC or 
wireless LAN device user guide for detailed information.
*   If using the existing network via access...

20

When configuring or controlling the projector via a web browser, an ID and 
password are required. There are two types of IDs, Administrator IDs and User 
IDs. The following chart describes the differences between user and administrator 
IDs.
Below are the factory default settings for administrator IDs, user IDs and 
passwords.
ItemDescriptionAdministrator IDUser ID
Network InformationDisplays the projector’s current network configuration settings.√√
Network SettingsDisplays and configures network...



2. Equipment connection and network setting
Refer to the following for configuring or controlling the projector via a web browser.
Example: If the IP address of the projector is set to 192.168.1.10:
1)  Enter 
[http://192.168.1.10/] into the address 
bar of the web browser and the screen 
in Fig. 2.5.a will be displayed.
2)  Enter your ID and password and click 
[Logon].
If the logon is successful either the Fig.2.5.b or Fig.2.5.c screen will be displayed.
3)  Click the desired operation or...



2. Equipment connection and network setting
2.5.1 Network Information
All screen images displayed in this manual are 
screens of a logon using an administrator ID.
Any administrator only functions will not be 
displayed when using a user ID. Refer to the 
descriptions in each table.
Displays the projector’s current network configuration settings.
ItemDescription
DHCPDisplays the DHCP configuration settings.
IP AddressDisplays the current IP address.
Subnet MaskDisplays the Subnet Mask....



2. Equipment connection and network setting
2.5.2 Network Settings
Displays and configures network settings.
ItemDescription
NETWORK MODESelect Network mode "wired" or "wireless".
IP ConfigurationConfigures network settings.
DHCP ONEnables DHCP.
DHCP OFFDisables DHCP.
IP AddressConfigures the IP address when DHCP is disabled.
Subnet MaskConfigures the Subnet Mask when DHCP is disabled.
Default GatewayConfigures the Default Gateway when DHCP is disabled.
Projector...

24

Click the [Apply] button to save the settings.
• The new configuration settings are activated after restarting the 
network connection. When the configuration settings are changed, you must 
restart the network connection. You can restart the network connection by 
clicking [Network Restart] on the main menu.
• If you connect the projector to an existing network, consult a network 
administrator before setting server addresses.
NOTE
2. Equipment connection and network setting
2.5.2 Network Settings...



2. Equipment connection and network setting
2.5.3 Port Settings
Displays and configures communication port settings.
Click the [Apply] button to save the settings.
• The new configuration settings are activated after restarting the 
network connection. The network connection must be restarted when the 
configuration settings are changed. The network connection can be restarted 
using [Network Restart] on the main menu.
NOTE
ItemDescription
Network Control Port1 (Port:23)Configures command...



2. Equipment connection and network setting
2.5.4 Mail Settings
Displays and configures e-mail addressing settings.
Click the [Apply] button to save the settings.
• You can confirm whether the mail settings work correctly using the 
[Send Test Mail] button.
• If you connect the projector to an existing network, consult a network 
administrator before setting server addresses.
NOTE
ItemDescription
Send MailClick the [Enable] check box to use the e-mail function. Configure the conditions for...