Dukane Imagepro 8776-W Lcd Projector Users Manual



The projector can be automatically controlled via scheduling.
• You can schedule the following control events: Power ON/OFF, Input 
Source and Transferred Image Display. 
• There are 3 types of Scheduling, 1) daily 2) day of the week 3) specific date.
• The priority for scheduled events is as follows 1) specific date 2) day of the 
week 3) daily.
• Up to five specific dates are available for scheduled events. Priority is given to 
those with the lower numbers when more than one event has...



Date/Time Settings (34)
The Date/Time setting can be adjusted via a web browser.
Example: If the IP address of the projector is set to 192.168.1.10/:
• A Network Restart is required after the Daylight Savings Time or 
SNTP configuration settings have been changed.
• The battery for the built in clock may be dead if the clock loses time even 
when the DATE and TIME have been set correctly. Replace the battery by 
following the instructions on replacing the battery.
(Internal clock battery...



Schedule Settings (32)
Schedule settings can be configured from a web browser.
Example: If the IP address of the projector is set to 192.168.1.10:
There are three types of scheduling.
 1) Daily: Perform the specified operation at a specified time every day.
 2)  Sunday ~ Saturday: Perform the specified operation at the specified time on a 
specified day of the week.
 3) Specific Date: Perform the specified operation on the specified date and time.
• In Standby mode the power indicator will...

74

The projector can display a still image that is transferred via the network.
e-SHOT transmission requires an exclusive application for your PC. You can 
download it from the Hitachi web site (http://hitachi.us/digitalmedia). Refer to the 
manual for the application for instructions.
4. Utilize projector – Advanced -
4.7 e-SHOT (Still Image Transfer) Display
Supported file types are JPG, BMP and PNG. 



You can configure and control the projector via the network using RS-232C 
commands.
Communication Port
The following two ports are assigned for the command control.
     TCP #23
     TCP #9715
Command Control Settings (25)
Configure the following items from a web browser when command control is used.
Example: If the IP address of the projector is set to 192.168.1.10:
• Command control is not available via communication port (TCP 
#9716) that is used for the e-Shot transmission function....



Command Control Settings (Continued)
When the authentication setting is enabled, the following settings are required.
(36)
 7) Click [Security Settings] on the main menu.
 8)  Click [Network Control] and enter the desired authentication password. * See 
NOTE1.
 9) Click the [Apply] button to save the settings. * See NOTE2.
• The Authentication Password will be the same for [Network Control 
Port1 (Port: 23)], [Network Control Port2 (Port: 9715)], and [Image Transfer 
Port (Port: 9716)]....



Command format
Command formats differ among the different communication ports.
     TCP #23
You can use the RS-232C commands without any changes. The reply data format 
is the same as the RS-232C commands. However, the following reply will be sent 
back in the event of authentication failure when authentication is enabled.

ReplyError code
0x1F0x040x00
     TCP #9715
Send Data format
The following formatting is added to the header (0x02), Data length (0x0D), 
Checksum (1byte) and Connection...

78

Reply Data format
The connection ID (the data is same as the connection ID data on the sending 
data format) is attached to the RS-232C commands reply data.

ReplyConnection ID
0x061 byte

ReplyConnection ID
0x151 byte

ReplyError codeConnection ID
0x1C2 bytes1 byte



ReplyDataConnection ID
0x1D2 bytes1 byte
ReplyStatus codeConnection ID
0x1F2 bytes1 byte
ReplyAuthentication Error codeConnection ID
0x1F0x040x001 byte
4. Utilize projector – Advanced - 



Automatic Connection Break
The TCP connection will be automatically disconnected after there is no 
communication for 30 seconds after being established.
Authentication
The projector does not accept commands without authentication success 
when authentication is enabled. The projector uses a challenge response type 
authentication with an MD5 (Message Digest 5) algorithm.
When the projector is using a LAN, a random eight bytes will be returned if 
authentication is enabled. Bind this...

80

5. Troubleshooting
5. Troubleshooting
ProblemLikely CauseThings to CheckReference Page Number
No image
The projector is not turned on.Is the projector's lamp on?*17
The projector's input source isn't switched to MIU.Is the projector switched to MIU?*18
Wireless / Wired
Live Mode
The projector that you want to connect to is nowhere to be found on the list of available projectors
The PC and/or projector's network settings are not configured correctly.
Check both the PC and...