Dukane Imagepro 8768 Liquid Crystal Projector Users Manual

31
3. Projecting an Image (Basic Operation)
Note on Startup screen (Menu Language Select screen)
When you first turn on the projector, you will get the Star tup screen. This screen gives you the opportunity to select one
of the 19 menu languages.
To select a menu language, follow these steps:
1. Use the SELECT 
 or  button to select one of the
19 languages for the menu.
3D REFORMSOURCE
STATUSLAMP 
PC CARD POWERON/STAND BY AUTO ADJUST
MENU
ENTERCANCEL
SELECT
MENU
ENTERCANCEL
OFF
12 VIDEO
S-VIDEOAUTO...

32
3. Projecting an Image (Basic Operation)
 Selecting a Source
Selecting the computer or video source
3D REFORMSOURCE
SELECT
STATUSLAMP 
PC CARD POWERON/STAND BY AUTO ADJUST
MENU
ENTERCANCELMENU
ENTERCANCEL
PJ
OFF
AUTO ADJ.
ON
SELECT
POWER
12 VIDEOS-VIDEOCOMPUTERCOMPONENT
Using the Remote Control
Press any one of the COMPUTER 1/2, COMPONENT, VIDEO,
S-VIDEO or VIEWER buttons.
Selecting from Source List
Press and quickly release the SOURCE button on the projec-
tor cabinet to display the Source list....

33
3. Projecting an Image (Basic Operation)
Place your projector on a flat level surface and ensure that the projector is
square to the screen.
Lift the front edge of the projector to center the image vertically.
If the projected image does not appear square to the screen then use the
Keystone feature for proper adjustment. See pages 35 and 44.
 Adjusting the Picture Size and Position
Adjust the Tilt Foot
1. Lift the front edge of the projector.
2. Push up and hold the Adjustable Tilt Foot Button on the...

34
3. Projecting an Image (Basic Operation)
ZOOM FOCUS 
Z
O
O
M
 FOCUS 
Zoom
Use the ZOOM lever to finely adjust the image size on the screen.
You can use the ZOOM lever to enlarge or reduce an image size.
Focus
Use the FOCUS ring to obtain the best focus. 

35
 Correcting Keystone Distortion
Auto Keystone Correction
The Auto Keystone correction feature will correct vertical distortion of a projected image on the screen. No special
operation required. Just put the projector on a flat surface.
Manual Keystone Correction
You can also correct keystone distortion manually.
To  do so:
1. Extend the Adjustable Tilt Foot to adjust the height of a projected
image. See page 33.
The Keystone screen will be displayed on the screen.
•If the Keystone screen disappears,...

36
5. Repeat steps 3 and 4 to correct keystone distortion.
6. After completing Keystone correction, press the ENTER button.
The Keystone screen will disappear.
•  To perform Keystone correction again, press the 3D REFORM button
to display the Keystone screen and repeat above steps 1 to 6.
NOTE:
•Turning on the projector will reset the previous correction setting values if the projection angle is changed from the last use.
    If the projection angle is the same as in the last use, the previous correction...

37
3. Projecting an Image (Basic Operation)
 Optimizing RGB Picture Automatically
Adjusting the Image Using Auto Adjust
Optimizing an RGB image automatically.
Press the Auto Adjust button to optimize an RGB image automatically.
[Poor picture]
[Normal picture]
3D REFORMSOURCE
SELECT
STATUSLAMP 
PC CARD POWERON/STAND BY AUTO ADJUST
MENU
ENTERCANCELMENU
ENTERCANCEL
OFF
12 VIDEO
S-VIDEOAUTO ADJ.
COMPUTERCOMPONENT
ON
SELECT
POWER
Press the Auto Adjust button to fine-tune the computer image or to remove any...

38
 Turning off the Projector
To turn off the projector:
3. Projecting an Image (Basic Operation)
3D REFORMSOURCE
SELECT
STATUSLAMP 
PC CARD POWERON/STAND BY AUTO ADJUST
MENU
ENTERCANCELMENU
ENTERCANCEL
OFF
12 VIDEO
S-VIDEOAUTO ADJ.
COMPUTERCOMPONENT
ON
SELECT
POWERFirst, press the POWER (ON/STAND BY) button on the projec-
tor cabinet or the POWER OFF button on the remote control for
a minimum of two seconds.
The power indicator will glow orange. After the projector turns
off, the cooling fans keep...

39
4
Convenient Features
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

 Switching Operation Mode between
Computer and Projector ........................................ 40
 Turning Off the Image and Sound .............................. 40
 Freezing a Picture ...................................................... 40
 Using the Pointer ....................................................... 41
 Enlarging and Moving a Picture ................................. 41
 Getting the On-line Help...

40
PJ
MENU
ENTERCANCEL
SOURCE
FREEZE OFF
12 VIDEO
S-VIDEOAUTO ADJ.
COMPUTER
VIEWER
COMPONENT
ON
3D REFORMASPECT
HELP
PICTUREPIC-MUTEPOINTER
VOLUME MAGNIFY
SLIDE
SELECT
POWER
PJ
MENU
ENTERCANCEL
SOURCE
FREEZE OFF
12 VIDEO
S-VIDEOAUTO ADJ.
COMPUTER
VIEWER
COMPONENT
ON
3D REFORMASPECT
HELP
PICTUREPIC-MUTEPOINTER
VOLUME MAGNIFY
SLIDE
SELECT
POWER
Not lit
Works as a mouse for your computer.
Works as a right-click button
for your computer.
Works as the SELECT button on the projector.
Lit red
Works as the...