Digital Projection Titan Wuxga 3d , Dual 3d, Titan Wuxga 330, 660 User Manual

							Rev A  April 2011 Page 4.17
Digital Projection TITAN WUXGA 3D, Dual 3D, 330. 660 User Manual 4. Controlling the projector
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section 4, Overview .
Notes
 Some  menu controls can be 
accessed directly using the 
control keys (see earlier in this 
section).
 When the OSD is OFF, all menu 
navigation keys will be disabled.
  When the OSD is switched back 
ON, the menus will remain OFF 
until the  
 key is pressed 
again. The menus will then 
reopen at the same point they 
were last viewed.
 If a menu is opened, and no 
other key is pressed within the 
period set in the  OSD Timeout 
menu, then the menus will 
disappear. When the  
 key 
is pressed again, the menus will 
reopen at the same point they 
were last viewed.
  (see On Screen Display, 
in Setup Menu, later in this 
section).)
 
Main menu: Input
 
Main menu: Setup
Using the menus
Navigating menus and submenus
When the menus are in use and the OSD is ON, the  top level menu headings are 
always visible to the left of the screen.
Each menu item can lead to a number of  submenus, which are displayed in the 
column to the right . The 
 symbol indicates that a submenu is available.
Each submenu can lead to further submenus, up to a maximum of three levels.
To display the menus, press 
 on the remote control or the keypad.
 The menus will always open at the same point they were last viewed. The 
example below shows the first menu display following power on – the item that is 
currently selected (the Input menu) is highlighted in blue.
To select a menu, press 
 and , for example the Setup menu:
•
•
• 
						

							Page 4.18 Rev A  April 2011
4. Controlling the projector Digital Projection TITAN WUXGA 3D, Dual 3D, 330. 660 User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Press  to open the menu. The blue highlight moves to the first item in the 
menu, which may be submenu, for example the Projector Setup submenu.
To select a submenu, press 
 and  , for example the Lamp submenu. 
Press 
 to open the submenu. The submenu opens, with the title at the top.
To close the submenu and return to the previous level, press .
There may be up to three levels of submenu, so to return to the top level, you 
may have to press 
 up to three times.
To close the menu display completely, press .
•
•
•
•
•Notes
 
Setup menu
 
Setup menu  
 Lamp
 
Setup menu 
						

							Rev A  April 2011 Page 4.19
Digital Projection TITAN WUXGA 3D, Dual 3D, 330. 660 User Manual 4. Controlling the projector
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section 4, Overview .
Slider bar
The highlighted slider bar shows which 
control is active currently.
To adjust the slider press 
 and .
Parameter selection
To select from a number of parameters, 
(shown one at a time to the right), 
press 
 and .
These two items are greyed out and 
the values are blank, showing that they 
are not available, due to the effect of 
settings made in other menus, or due 
to the type of input signal.
Parameter list
To select from a list of parameters, 
press 
 and .
Menu controls
Some menus have controls, as shown in the examples below.
Notes
 Some  menus items may be 
greyed out - unavailable due to 
the effect of settings made in 
other menus, or due to the type 
of input signal. 
						

							Page 4.20 Rev A  April 2011
4. Controlling the projector Digital Projection TITAN WUXGA 3D, Dual 3D, 330. 660 User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Input menu
 To return to the main menu, press  up to three times.
 From the main menu:
Press 
 and   until Input is highlighted.
Press  to open the Input menu. The blue highlight moves to the first item in 
the menu. The  symbol shows which input is currently selected.
Input Source
Press  and   to select from:
1. RGB1
2. RGB2
3. DVI (Single)
4. SDI
5. Composite Video
6. S-Video
7. Component
8. DVI (Single/Dual/Twin pixel-mapped)
Press 
 to confirm your selection.
•
•
•
Notes
  Some  menu controls can be 
accessed directly using the 
control keys (see earlier in this 
section).
 When using the menus, press 
OSD  or  to hide or 
reveal the On-Screen-Display.
 
Input Menu
 For more information about 
the input connections, see 
section 2. Installation, and 
section 7. Appendix.
  Input 8 and 3D may not be 
present on some models
 3D signals will be displayed 
in 3D, only if 3D Enable is set 
to on: see later in this section, 
Setup Menu, 3D .
 WUXGA models only: 
3D images are possible only on 
Input 8.
  When an input has been 
selected, the projector will 
automatically detect input mode 
settings such as line rate and 
resolution etc.
  To force the projector to re-
detect the input mode settings, 
press 
. 
						

							Rev A  April 2011 Page 4.21
Digital Projection TITAN WUXGA 3D, Dual 3D, 330. 660 User Manual 4. Controlling the projector
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section 4, Overview .
Notes
 Some  menu controls can be 
accessed directly using the 
control keys (see earlier in this 
section).
 For more information about 
input modes and input presets, 
see earlier in this section,  Input 
modes and settings.
  The lens settings are the only 
settings saved for Input 8.
 
Input Menu 
  Presets
 
Input Menu 
 Presets 
    Recall Presets A ~ H
 The lens settings, ie Focus 
position, Zoom position and 
Shift, are included only for the 
first ten presets.
 The lens settings are the only 
settings recalled for Input 8.
Presets
Sixteen sets of parameters can be saved and recalled  (A – S). The parameters 
saved for each Preset are:
all settings from the Picture menu,
all settings from the Input menu
all settings from the Geometry menu, except Keystone
all settings from the Colour menu, except the Global settings
all lens position, focus and zoom settings
Press 
 and   to select Presets. 
 Press  to open the Presets submenu.
recall Presets
Press  and   to select Recall Preset.
 Press  to open the Recal Presets A ~ H submenu. Any presets that have 
been saved are indicated by their description, for example D: in this example.
To recall a set of parameters that has been saved, press 
 and   to select 
one of the Presets.
 For Presets J to S, select Recall Preset J ~ S then press  to open the 
J~S submenu. Press  and   to select the Preset.
 Press  to confirm your selection.
 The Preset parameters will be loaded.
•
•
•
•
Input menu continued 
						

							Page 4.22 Rev A  April 2011
4. Controlling the projector Digital Projection TITAN WUXGA 3D, Dual 3D, 330. 660 User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Notes
 Some  menu controls can be 
accessed directly using the 
control keys (see earlier in this 
section).
 
Input Menu 
  Presets 
    Save Presets A ~ H
 The lens settings, ie Focus 
position, Zoom position and 
Shift, are included only for the 
first ten presets.
 The lens settings are the only 
settings saved for Input 8.
Save Presets
Press  and   to select Save Preset.
 Press  to open the Save Presets A ~ H submenu.
To save the current set of parameters, press  and   to select one of the 
Presets.
 For Presets J to S, select Save Preset J ~ S then press  to open the 
J~S submenu. Press  and   to select the Preset.
 Press  to confirm your selection.
 If this Preset has been used before, but only if the Input source has been 
changed, then the following  message will be displayed.
 Press  and   to select either OK or Cancel.
 Press  to confirm your selection.
 The parameters will be saved to the selected preset, and the following message 
will be displayed.
•
•
Input menu continued 
						

							Rev A  April 2011 Page 4.23
Digital Projection TITAN WUXGA 3D, Dual 3D, 330. 660 User Manual 4. Controlling the projector
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section 4, Overview .
Notes
 
Input Menu 
 Presets 
    Delete Presets A ~ H
Delete Presets
Press  and   to select Delete Preset.
 Press  to open the Delete Presets A ~ H submenu.
To delete a saved set of parameters, press  and   to select one of the 
Presets.
 For Presets J to S, select Delete Preset J ~ S then press  to open the 
J~S submenu. Press  and   to select the Preset.
 Press  to confirm your selection.
The following  message will be displayed.
 Press  and   to select either OK or Cancel.
 Press  to confirm your selection.
 The preset will be deleted, and the following message will be displayed.
•
•
Input menu continued 
						

							Page 4.24 Rev A  April 2011
4. Controlling the projector Digital Projection TITAN WUXGA 3D, Dual 3D, 330. 660 User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Notes
 Some  menu controls can be 
accessed directly using the 
control keys (see earlier in this 
section).
 When using the menus, press 
OSD  or  to hide or 
reveal the On-Screen-Display.
 
Picture Menu
 Some menu items may be 
greyed out - unavailable due to 
the effect of settings made in 
other menus, or due to the type 
of input signal.
 The Saturation slider is 
available for Composite, S-
Video and Component inputs 
only.
  The Hue slider is available for 
NTSC inputs only.
Picture menu
  To return to the main menu, press  up to three times.
 From the main menu:
Press 
 and   until Picture is highlighted.
Press  to open the Picture menu. The blue highlight moves to the first item in 
the menu.
Brightness
Press  and   to select Brightness.
  Press  and   to adjust the slider (-128 to +127).
Contrast
Press  and   to select Contrast.
 Press  and   to adjust the slider (-128 to +127).
Saturation
Adjusts the saturation at white peak levels.
Press 
 and   to select Saturation.
 Press  and   to adjust the slider (0 to 255).
Hue
Adjusts the color balance from green to blue, using the red level as a r\
eference.
Press 
 and   to select Hue.
 Press  and   to adjust the slider (0 to 255).
•
•
•
•
• 
						

							Rev A  April 2011 Page 4.25
Digital Projection TITAN WUXGA 3D, Dual 3D, 330. 660 User Manual 4. Controlling the projector
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section 4, Overview .
Notes
 For more information about 
User gamma settings, see 
section 5. Userware .
 Parametric Gamma adjustment 
is available only when 
Parametric  is selected in 
Gamma selection, above.
 Phase adjustment can be 
found in both the Picture and 
Geometry menus, and is 
available for RGB1 and RGB2 
inputs only.
  The Phase adjustment is NOT 
available for Input 8.
Gamma Correction
Video recordings are often supplied with a gamma adjustment applied. The \
projector’s gamma adjustment can be used to correct for this.
Press 
 and   to select Gamma.
 Press  and   to select from:
Parametric  Enables the gamma slider
User download Applies the gamma settings made externally using the DP 
Userware on a personal computer. (default gamma of 2.2)
2.2 Limited DVI
  Expands DVI signal to use full dynamic range with gamma 2.2
2.4 Limited DVI Expands DVI signal to use full dynamic range with gamma 2.4
Graphics  Enhanced highlights and contrast
NTSC  NTSC colour space, with a gamma of 2.2
PAL  PAL colour space, with a gamma of 2.2
Linear gamma of 1.0
Punch Enhanced brightness and increased colour saturation for high 
ambient environments.
Parametric Gamma
Press  and   to select Parametric Gamma.
 Press  and   to adjust the slider (1.0 to 3.0 in 0.1 steps).
Phase
Phase should be set automatically by the projector, but can be adjusted manually to 
correct for shimmering or poor quality definition on, for example, fine \
text.
Press 
 and   to select Phase.
 Press  and   to adjust the slider (0 to 31).
•
•
•
Picture menu continued 
						

							Page 4.26 Rev A  April 2011
4. Controlling the projector Digital Projection TITAN WUXGA 3D, Dual 3D, 330. 660 User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Notes
 Aspect Ratio selection can be 
found in both the Picture and 
Geometry menus.
 When User Aspect  is selected, 
the Aspect Ratio settings are 
taken from the User H Aspect  
and V Aspect settings made in 
the Geometry menu.
 Aspect Ratio selection is NOT 
available for Input 8.
  WUXGA models only: 
The full height of the DMD can 
be used only by WUXGA and 
UXGA images.
  For more information, see 
Screen requirements  in 
section 2. Installation.
 The Sharpness slider is 
available for Composite, 
S-Video and Component SD 
inputs only.
Aspect Ratio
Press  and   to select Aspect Ratio.
  Press  and   to select from:
Fill  This will best fit the incoming source to fill either the height or 
width without changing the aspect ratio of the source.
User Aspect
1.33:1 (4:3)
1.6:1 (16:10)
1.78:1 (16:9)
2.35:1 (Scope)
1.66:1 (Vista)
1.85 (Flat)
Theaterscope
  Use with the TheaterScope Anamorphic System only. The 
2.35:1 source image is displayed using the full area of the 16:9 
DMD. This is then stretched to 2.35:1 by the lens.
Native
  The image will be displayed pixel for pixel. The image will be 
centred, with a black border if smaller than full resolution or 
cropped if larger.
Sharpness
Press  and   to select Sharpness.
 Press  and   to adjust the slider.
•
•
Picture menu continued