Digital Projection Titan Wuxga 3d , Dual 3d, Titan Wuxga 330, 660 User Manual

							Rev A  April 2011 Page 5.25
Digital Projection TITAN WUXGA 3D, Dual 3D, 330. 660 User Manual 5. Userware
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Notes
 For more information about the 
FastFrame settings, see Setup 
menu, in section 
4. Controlling 
the projector.
FastFrame page
To see the FastFrame page, click on F-Frame.
FastFrame Enable
Click on FastFrame Enable to turn FastFrame mode On  or Off .
Dark Time
Use the slider to adjust the  Dark Time.
•
•
• 
						

							Page 5.26 Rev A  April 2011
5. Userware Digital Projection TITAN WUXGA 3D, Dual 3D, 330. 660 User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Notes
 For more information about 
lamp mode, see  Setup menu, 
in section 
4. Controlling the 
projector.
System page
To see the System page, click on System .
OSD
Click on OSD to turn the on-screen display On  or Off .
Backlight
Click on Backlight to turn the control panel backlight On  or Off .
DMD controls
Click on the DMD buttons to turn each DMD On or Off.
Lamp mode
Click on Lamp mode to select from the drop down menu.
Lamp Power slider
Use the slider to adjust the lamp power from 80% to 100%.
•
•
•
•
•
• 
						

							Rev A  April 2011 Page 5.27
Digital Projection TITAN WUXGA 3D, Dual 3D, 330. 660 User Manual 5. Userware
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Notes
 The Connect page is available 
only on the Standalone version 
of the Userware.
  The Userware can be used to 
control only one projector at a 
time, and only one instance can 
be running at one time.
  The Connect page can be 
used to switch control between 
multiple projectors.
  More than one computer can be 
used to control more than one 
projector on the same network.
Connect page
To see the Connect page, click on Connect.
Refresh
Click on Refresh  to search the network for projectors.
 Any projectors previously connected, that are now no longer online, will be 
marked Unreachable.
Connect
To connect to a projector, click on one of the  LAN IP addresses in the list, then 
click on Connect.
or
  Double click on a LAN IP address.
Any projector previously connected will be disconnected, and the Userware will 
connect to the new projector.
  The LAN IP address of the projector that is connected will be highlighted.
 Projector Connected will be shown at the top left of all pages, together with the 
projector’s Serial No and Model.
Disconnect
To disconnect from the projector, click on Disconnect
 Projector Disconnected will be shown at the top left.
•
•
•
• 
						

							Page 5.28 Rev A  April 2011
5. Userware Digital Projection TITAN WUXGA 3D, Dual 3D, 330. 660 User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview . 
						

							Rev A  April 2011 Page 6.1
6. Maintenance
Contents
Changing the lamp module ........................................................................\
......................................6.2
Changing the air filters ........................................................................\
..............................................6.2
Cleaning ........................................................................\
........................................................................\
6.3
Projector ........................................................................\
..................................................................6.3
Lens ........................................................................\
........................................................................6.3 
						

							Page 6.2 Rev A  April 2011
6. Maintenance Digital Projection TITAN WUXGA 3D, Dual 3D, 330. 660 User Manual
Changing the air filters
The air filters should be changed only by qualified and authorised service 
personnel.
Contact your Digital Projection Dealer.
•
•
Changing the lamp module
The lamp module should be changed only by qualified and authorised service 
personnel.
Contact your Digital Projection Dealer.
•
•
Notes
 
The lamp and filters in this 
projector should be changed 
ONLY by authorised and 
qualified service personnel.
 Always allow the lamp to cool 
for 5 minutes before: 
- disconnecting the power  
- moving the projector.
  At the end of life, the lamp 
will not strike, and the Lamp 
Indicator on the control panel 
will show red. (Typical lamp life 
is 2000 hours)
 Do not use the lamp for more 
than 2000 hours, as this may 
cause serious lamp failure, 
damage the lamp module 
and cause extra cost on 
replacement. 
 HID lamps produce high 
intensity light. Do not look 
directly at the light coming 
from the lamp housing or the 
lens.
  The filters should be changed 
at the same time as the lamp is 
changed.
 The air filters should be 
changed regularly:
  - In a clean environment such 
as an office, change after 2000 
hours, at the same time as the 
lamp is changed.
 - In a dusty or smoky 
environment such as a theatre 
or public area, more frequent 
changes may be necessary. 
						

							Rev A  April 2011 Page 6.3
Digital Projection TITAN WUXGA 3D, Dual 3D, 330. 660 User Manual 6. Maintenance
Notes
 Always allow the lamp to cool 
for 5 minutes before:
 - disconnecting the power  
- moving the projector.
  Never use strong detergents 
or solvents such as alcohol 
or thinners to clean the 
projector and lens.
Cleaning
Turn the projector off before cleaning.
Projector
Clean the cabinet periodically with a damp cloth. If heavily soiled, use a mild 
detergent.
Lens
Use a blower or lens paper to clean the lens, taking care not to scratch the glass. 
						

							Page 6.4 Rev A  April 2011
6. Maintenance Digital Projection TITAN WUXGA 3D, Dual 3D, 330. 660 User Manual 
						

							Rev A  April 2011 Page 7.1
7. Appendix
Contents
Troubleshooting ........................................................................\
..........................................................7.2
Specifications ........................................................................\
..............................................................7.4
Part numbers ........................................................................\
............................................................7.4
Optical ........................................................................\
.....................................................................7.4
Electrical ........................................................................\
..................................................................7.5
Physical ........................................................................\
...................................................................7.5
Lens Data ........................................................................\
................................................................7.6
Dimensions ........................................................................\
..................................................................7.8
Input modes supported by inputs 1-7 ........................................................................\
....................7.9
Input connections ........................................................................\
.....................................................7.10
1. RGB1 input ........................................................................\
.........................................................7.10
2. RGB2 input ........................................................................\
.........................................................7.10
3. DVI-D Single input ........................................................................\
................................................7.1 1
4. SDI input ........................................................................\
............................................................7.12
5. Composite video input ........................................................................\
.........................................7.12
6. S-Video input ........................................................................\
......................................................7.12
7. Component video input ........................................................................\
........................................7.12
8. DVI-D Single/Dual/Twin input ........................................................................\
...............................7.13
Control connections ........................................................................\
................................................7.14
Wired Remote control connection ........................................................................\
.............................7.14
LAN connection ........................................................................\
......................................................7.14
Crossed cable ........................................................................\
......................................................7.14
3D sync ........................................................................\
.................................................................7.15
Serial control input ........................................................................\
..................................................7.15
Null-modem cable ........................................................................\
.................................................7.15
Serial port settings ........................................................................\
................................................7.15
Remote communications protocol ........................................................................\
.......................7.16
Introduction ........................................................................\
............................................................7.16
Message Structure ........................................................................\
..................................................7.16
Operation Messages ........................................................................\
.............................................7.17
Enhanced Messages ........................................................................\
.............................................7.18
Operation Command examples ........................................................................\
................................7.19
Power  (0102) ........................................................................\
.....................................................7.19
Source  (3702) ........................................................................\
....................................................7.20
Brightness (E502) ........................................................................\
................................................7.21
Contrast (E602) ........................................................................\
...................................................7.22
Shutter  (CF02) ........................................................................\
...................................................7.23
Quick Reference chart ........................................................................\
.............................................7.24 
						

							Page 7.2 Rev A  April 2011
7. Appendix Digital Projection TITAN WUXGA 3D, Dual 3D, 330. 660 User Manual
Troubleshooting
Problem Possible solutions
The projector will not power up. Check that the mains plug is plugged in and that the mains supply is switched on.
Check any external fuses or breakers.
The projector shuts down after it has 
been in use for some time. The projector may be overheating. Check that the air inlets and outlets are clear 
of any obstruction. Check that the air filter is clean, and if it is dirty
, fit a new one.
See section 1. Introduction, Getting to know the projector
No image is displayed. Check the lamp indicators on the control panel. If both indicators are red, then 
both lamps are faulty.
See section 5. Maintenance, Changing the lamp
Check that the input source is switched on and connected to the projector 
correctly.
Check that the correct image source is selected.
See section 4. Controlling the projector, Using the control keys and Input 
menu
Check that the brightness and contrast settings are set correctly .
See section 4. Controlling the projector, Picture menu
The projector may be overheating. Check that the air inlets and outlets are clear 
of any obstruction. Check that the air filter is clean, and if it is dirty, fit a new one.
The image does not fit the screen 
correctly. Check that the correct lens is being used for the combination of screen size and 
projection distance, and that the zoom is adjusted correctly.
See section 2. Installation, Choosing a lens
Check the image size settings.
See section 4. Controlling the projector, Picture or Geometry menus
Uneven image quality. Check that the projector is parallel to the screen.
Check that the screen is flat, and securely mounted.
Low image brightness. Check that the FastFrame Dark Time is not set too high.
See section 4. Controlling the projector, Setup menu
Poor colour depth reproduction. Colour depth is 8 bits using Single or Dual DVI inputs. If using Twin DVI inputs for 
greater colour depth, check that both source cables are connected correctly.
If using 3D mode, check the settings of the Dark Time and Sync Delay controls.
See section 4. Controlling the projector, Setup menu