Digital Projection Titan Wuxga 3d , Dual 3d, Titan Wuxga 330, 660 User Manual

							Rev A  April 2011 Page 5.5
Digital Projection TITAN WUXGA 3D, Dual 3D, 330. 660 User Manual 5. Userware
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Standalone version
To install the Userware, simply copy the file (from the CD, or downloaded from 
the Digital Projection website), to a folder on the computer.
Double click on the filename to start the software.
The Userware interface is organised into a number of pages, as listed below:
Show  Lens    Blend   Image   Screen
MCGD TCGD    3D   Global   Modal
info   FastFrame  System   Connect
Each page is described in full later in this section.
When the Userware is started, the Show page will display immediately. The  Page 
buttons are always visible at the bottom of the display:
Disconnect
To disconnect from the projector, go to the  Connect page and click on 
Disconnect.
reconnect
To reconnect, go to the Connect page and click on Connect.
•
•
•
•
Notes
 
To use the Titan Userware the 
java Runtime Environment 
software must be installed on 
your computer. This software 
can be downloaded, free of 
charge from www.java.com.
  The Userware can be used to 
control only one projector at a 
time, and only one instance can 
be running at one time.
  The Connect page can be 
used to switch control between 
multiple projectors.  
(see later in this section)
  More than one computer can be 
used to control more than one 
projector on the same network.
 The Connect page is described 
in more detail later in this 
section. 
						

							Page 5.6 Rev A  April 2011
5. Userware Digital Projection TITAN WUXGA 3D, Dual 3D, 330. 660 User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Show page
The Show page is the first to display when the browser connects to the projector .
To return to the Show page  at any time, click on Show.
On / Off
Click On to switch the projector On.
Click Off to switch the projector into Standby mode.
Shutter Open / Closed
Click on Shutter Open to open the shutter.
Click on Shutter Close to close the shutter.
Freeze / Un-Freeze
Click on Freeze to freeze the display on the current frame.
Click on Un-Freeze to un-freeze the display.
Picture sliders
Use the sliders to adjust the  Brightness, Contrast, Saturation, Hue and 
Sharpness of the display.
Click on the number above the slider to return to the default value.
•
•
•
•
•
•
•
•
•
Notes
 
The Freeze function is NOT 
available for Input 8.
Picture 
sliders 
						

							Rev A  April 2011 Page 5.7
Digital Projection TITAN WUXGA 3D, Dual 3D, 330. 660 User Manual 5. Userware
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Input Presets
recall
To recall a set of modal and lens* settings that have been saved:
Click on Preset , and select one of the Presets A - S, from the drop down menu.
Click on Recall.
  The projector will switch to the saved input source, and redetect the input mode 
before applying the saved modal and lens* settings.
Save
To save the current input source, mode, modal and lens* settings:
Click on Preset , and select one of the Presets A - S, from the drop down menu.
Click on Save.
  The settings will be saved to the selected preset.
•
•
•
•
Notes
  For more information about 
input modes and input presets, 
see Overview, in section 
4. Controlling the Projector.
 A preset can be applied only to 
the same mode for which it was 
created. If the detected input 
mode does not match, then 
settings from the mode history 
or mode library will be applied 
instead.
  For more information about 
input modes, see  Overview, 
in section 
4. Controlling the 
Projector.
  The lens settings, ie Focus 
position, Zoom position and 
Shift, are included only for the 
first ten presets.
 Presets can also be deleted: 
see Input menu , in section 
4. Controlling the Projector.
Show page continued
Preset 
						

							Page 5.8 Rev A  April 2011
5. Userware Digital Projection TITAN WUXGA 3D, Dual 3D, 330. 660 User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Orientation
Click on Orientation to select from the drop down menu.
Input
Click on Input to select from the drop down menu.
Test Pattern
Click on Test Pattern to select from the drop down menu.
Aspect Ratio
Click on Aspect Ratio to select from the drop down menu.
•
•
•
•
Notes
 
For more information about 
input modes, see  Overview, 
in section 
4. Controlling the 
Projector.
  Input 8 and 3D may not be 
present on some models
 The signal from input 8 will 
be displayed in 3D, only if  3D 
Enable is set to on: see 3D 
Menu, later in this section.
  For more information about 
test patterns, see Setup menu, 
in section 
4. Controlling the 
Projector.
 For more information about 
aspect ratios, see Picture 
menu and Geometry menu, 
in section 
4. Controlling the 
Projector.
Show page continued
Orientation
Input
Test 
PatternAspect  Ratio 
						

							Rev A  April 2011 Page 5.9
Digital Projection TITAN WUXGA 3D, Dual 3D, 330. 660 User Manual 5. Userware
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Notes
 Each time a new lens is 
fitted to the projector, 
the calibration procedure 
must be carried out. See 
Setup menu, in Section 4. 
Controlling the projector.
Lens page
To see the Lens page, click on Lens.
Lens controls
Click on the buttons to Move, Focus and Zoom the lens.
Click on 
 to centre the lens.
Shutter Open / Closed
Click on Open Shutter to open the shutter.
Click on Close Shutter to close the shutter.
Calibrate Focus
Click on Calibrate Focus to calibrate the lens focus mechanism.
Calibrate Zoom
Click on Calibrate Zoom to calibrate the lens zoom mechanism.
•
•
•
•
•
•
•
Lens 
controls 
						

							Page 5.10 Rev A  April 2011
5. Userware Digital Projection TITAN WUXGA 3D, Dual 3D, 330. 660 User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Notes
 For more information about 
Edge Blend, see  Setup menu, 
in Section 4. Controlling the 
projector.
Edge Blend page
To see the Edge Blend page , click on Blend.
Markers On / Off
Click on Markers On to display the overlap markers.
Click on Markers Off to remove the overlap markers.
Active Edges
Click on Top, Bottom, Left or Right  to enable or disable the blend for each 
edge.
Input 8 DVI 3D Resolution
Click on Input 8 DVI 3D Resolution  to select from the drop down menu.
Overlap Width
Use the sliders to adjust the Overlap width for each edge.
•
•
•
•
•
• 
						

							Rev A  April 2011 Page 5.11
Digital Projection TITAN WUXGA 3D, Dual 3D, 330. 660 User Manual 5. Userware
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Notes
 For more information about 
Black Level Uplift, see 
Setup menu,  in Section 4. 
Controlling the projector.
 Non-Addressable Border 
should always be set to 
Manual.
Black Level Uplift page
To see this page, click on  Black Level Uplift on the Edge Blend page .
x2, x4 Region Uplift
Use the sliders to adjust the amount of Uplift for each region.
Non-Addressable Border
Click on Non-Addressable Border to select from the drop down menu.
Use the sliders to adjust the size of the  Non-Addressable Border for each 
edge.
Back to Edge Blend
Click on Back to Edge Blend to return to the Edge Blend  page.
•
•
•
•
•
Border 
controls
Edge Blend page continued 
						

							Page 5.12 Rev A  April 2011
5. Userware Digital Projection TITAN WUXGA 3D, Dual 3D, 330. 660 User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Notes
 Changing the Colour Space 
on this page manually 
overrides the colour space 
for analogue component 
inputs, which may result in an 
incorrectly displayed image.
  The Component selection is 
available for the Component 
input only.
  For more information about 
phase, see Picture menu and 
Geometry menu, in section 
4. Controlling the Projector.
 The Phase slider is available for 
RGB1 and RGB2 inputs only.
  For more information about 
Gamma, see Picture menu, 
in section 
4. Controlling the 
Projector.
 User download of Gamma 
correction tables is not yet 
available.
 The Parametric  slider is 
available only when  Parametric 
is selected in  Gamma 
Correction.
Image page
To see the Image page, click on Image.
Colour Space
Click on Colour Space to select from the drop down menu.
Component
Click on Component to select from the drop down menu.
Phase slider
Use the slider to adjust the  Phase.
Gamma
Click on Gamma Correction to select from the drop down menu:
Parametric slider
Use the slider to adjust the Gamma manually.
•
•
•
•
•
•
Component
Phase 
slider
Colour Space
Parametric  slider
Gamma 
Correction 
						

							Rev A  April 2011 Page 5.13
Digital Projection TITAN WUXGA 3D, Dual 3D, 330. 660 User Manual 5. Userware
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Notes
 The Convergence controls 
open in a new window, to allow 
you to visit the Show page , in 
order to display a  Test Pattern.
Convergence controls
To see these controls, click on  Convergence on the Image page.
The Convergence controls open in a new window.
Horizontal Convergence
Use the sliders to adjust the position of the  Blue and Green components of the 
image relative to the Red component.
Vertical Convergence
Use the sliders to adjust the position of the  Blue and Green components of the 
image relative to the Red component.
Close
Click on Close to close the Convergence controls window.
•
•
•
•
Image page continued 
						

							Page 5.14 Rev A  April 2011
5. Userware Digital Projection TITAN WUXGA 3D, Dual 3D, 330. 660 User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Notes
 The blanking curtains will not 
applied until  Blanking is turned 
On.
  For more information about 
blanking, see  Geometry menu, 
in section 
4. Controlling the 
Projector.
  For more information about 
keystone adjustment, see 
Geometry menu, in section 
4. Controlling the Projector.
Screen page
To see the Screen page, click on Screen.
Blanking On / Off
Click on Enable to turn the blanking On  or Off .
Blanking adjust
Use the sliders to adjust the  Top, Bottom, Left and Right blanking curtains.
Keystone adjust
Use the slider to adjust the  Keystone setting.
Position adjust
Use the sliders to adjust the  Horizontal and Vertical position of the image.
•
•
•
•
•