Digital Projection Titan 1080p-500, 1080p-250 User Manual
Have a look at the manual Digital Projection Titan 1080p-500, 1080p-250 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 577 Digital Projection manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
July 2007 Page 4.35 Digital Projection TITAN 1080p-500, 1080p-250 User Manual 4. Controlling the projector Lamp Press and to select Lamp. Press to open the Lamp submenu. The middle row shows the current lamp setting. Change Lamp Setting Press and to select Change Lamp Setting. Press to open the Lamp Setting control box. • • Notes Setup Menu Lamp Setup menu, continued continued
Page 4.36 July 2007 4. Controlling the projector Digital Projection TITAN 1080p-500, 1080p-250 User Manual Notes In single lamp modes: - if the running lamp fails, the other lamp will automatically be switched on. The Lamp 2 and Alternate settings apply only to the 1080p-500. The 1080p-250 has only one lamp. The selected lamp mode: - will not be applied until OK is selected - will be applied gradually over a period of 30 seconds - will not be applied until the end of any warm-up or cool-down period that has already started. The Lamp 2 indicator applies only to the 1080p-500. The 1080p-250 has only one lamp. Lamp Power Press and to select the Lamp Power setting. Press and to adjust the Lamp Power from: 80 to 100% in 1% steps Lamp Mode Press and to select Lamp Mode. Press and to select from: single lamp modes Lamp 1 lamp 1 only Lamp 2 lamp 2 only Alternate on power up, selects the lamp with the least hours used dual lamp mode Lamps 1 and 2 both lamps OK Press and to select OK. Press to apply the new settings. Cancel Press and to select Cancel. Press or to exit without applying the new settings. The indicators on the control panel will show as follows: Lamp 1 off = OFF fl ashing red = LAMP ERROR green = ON (100%) amber = (80 - 99%) fl ashing green/amber = LAMP COOL-DOWN or WARM-UP Lamp 2 off = OFF fl ashing red = LAMP ERROR green = ON (100%) amber = (80 - 99%) fl ashing green/amber = LAMP COOL-DOWN or WARM-UP • • • • Setup menu, Lamp continued
July 2007 Page 4.37 Digital Projection TITAN 1080p-500, 1080p-250 User Manual 4. Controlling the projector Notes Setup Menu On Screen Display The On Screen Display will move to the centre of the DMD when Blanking is turned On. (see Geometry menu, earlier in this section). If a menu is opened, and no other key is pressed within the period set in the OSD Timeout menu, then the menus will disappear. When the key is pressed again, the menus will reopen at the same point they were last viewed. On Screen Display Press and to select On Screen Display. Press to open the On Screen Display submenu. OSD Position Press and to select OSD Position Press and to select from: Upper Left Upper Centre Upper Right Middle Left Middle Centre Middle Right Lower Left Lower Centre Lower Right OSD Size Press and to select OSD Size. Press and to select from: Large Small OSD Timeout Press and to select the length of the On Screen Display Timeout. Press and to select from: 0 to 255 in 1 second steps (when set to zero, the OSD never times out) • • • • Setup menu continued
Page 4.38 July 2007 4. Controlling the projector Digital Projection TITAN 1080p-500, 1080p-250 User Manual Password Entry to the password protected area is available to authorised service personel only. Press and to select Password. Press to open the Password control box. Press and to select each digit in turn. Press and to adjust the digit from: 0 to 9 then move to the next digit. Use and to select from OK Press to enter the password controlled area. or Cancel Press or to exit without applying the password. • • Notes Setup menu continued
July 2007 Page 4.39 Digital Projection TITAN 1080p-500, 1080p-250 User Manual 4. Controlling the projector Notes Setup Menu Comunication When fresh batteries are inserted in the remote control, it will default to address 00. Remote control 00 is a master control, able to control all projectors. FIf two or more projectors are set to the same address, they can be controlled from one remote control, provided they are connected by cable or in range of the infra red. Communication Press and to select Comunication. Press to open the Comunication submenu. Projector Address The projector and the remote control need to be set to matching addresses. Read the note to the right on this page, and follow the instructions in the order shown below: 1 Set the projector address: Press to open the Projector address control box. Press and to select the address setting. Press and to adjust the address from: 00 to 99 Use and to select from Apply Press to apply the new Projector Address. or Cancel Press or to exit without making the change. 2 Set the remote control address as shown in Using the control keys, earlier in this section. • Setup menu continued
Page 4.40 July 2007 4. Controlling the projector Digital Projection TITAN 1080p-500, 1080p-250 User Manual Notes Setup Menu Network Some items may be greyed out or not editable, due to the effect of other settings made in the Network submenu. For example, if a Wired Connection is selected: Wifi , Channel and SSID will be unavailable. Setup menu continued Network Press and to select Network. Press to open the Network submenu. LAN MAC Address Projector’s unique ID - for information only - cannot be changed. Connection Press and to select Connection Press to open the Connection control box. Press and to select from: Wired Wireless Press to apply the new Connection setting. • • • Input Picture Geometry Colour Setup Information LAN MAC Address Connection DHCP LAN IP Address LAN Subnet LAN Gateway Channel SSID31-FE-A5-81-20-83 255.255.0.0 192.168.9.10192.168.3.6On 0 TITANWired NETWORK
July 2007 Page 4.41 Digital Projection TITAN 1080p-500, 1080p-250 User Manual 4. Controlling the projector Notes LAN IP Address cannot be changed if DHCP is set to ON. DHCP will set the the address, which will be displayed for information only. Setup menu, Network continued DHCP Press and to select DHCP Press to open the DHCP control box. Press and to select from: On Off Press to apply the new DHCP setting. LAN IP Address Press and to select LAN IP Address Press to open the LAN IP Address control box. Use and to select each number in turn. Use and to adjust the number then move to the next number. Use and to select from Apply Press to apply the new LAN IP Address. or Cancel Press or to exit without making the change. • •
Page 4.42 July 2007 4. Controlling the projector Digital Projection TITAN 1080p-500, 1080p-250 User Manual Notes LAN IP Subnet cannot be changed if DHCP is set to ON. DHCP will set the the subnet mask, which will be displayed for information only. LAN Subnet Mask Press and to select LAN Subnet Press to open the LAN Subnet control box. Press and to select from: Automatic or one of the following: Class C Masks 255.255.255.254 255.255.255.252 255.255.255.248 255.255.255.240 255.255.255.224 255.255.255.192 255.255.255.128 255.255.255.0 (selected when setting is Automatic and IP class is C ) Class B Masks 255.255.254.0 255.255.252.0 255.255.248.0 255.255.240.0 255.255.224.0 255.255.192.0 255.255.128.0 255.255.0.0 (selected when setting is Automatic and IP class is B) Class A Masks 255.254.0.0 255.252.0.0 255.248.0.0 255.240.0.0 255.224.0.0 255.192.0.0 255.128.0.0 255.0.0.0 (selected when setting is Automatic and IP class is A) Use and to select from Apply Press to apply the new LAN Subnet Mask. or Cancel Press or to exit without making the change. • Setup menu, Network continued
July 2007 Page 4.43 Digital Projection TITAN 1080p-500, 1080p-250 User Manual 4. Controlling the projector LAN Gateway Mask Press and to select LAN Gateway Press to open the LAN IP Address control box. Use and to select each number in turn. Use and to adjust the number then move to the next number. Use and to select from Apply Cancel Press to apply the new LAN Gateway Mask, or to exit without making the change. • Setup menu, Network continued Notes LAN IP Gateway cannot be changed if DHCP is set to ON. DHCP will set the the gateway mask, which will be displayed for information only.
Page 4.44 July 2007 4. Controlling the projector Digital Projection TITAN 1080p-500, 1080p-250 User Manual Channel Press and to select Channel. Press to open the Channel control box. Press and to select the channel number. Use and to adjust the channel number from: 0 to 14 Use and to select from Apply Press to apply the new Channel number. or Cancel Press or to exit without making the change. SSID Projector’s ID - for information only. • • Setup menu, Network continued Notes The Channel setting is not available if Connection is set to Wired.