Digital Projection Titan 1080p-500, 1080p-250 User Manual
Have a look at the manual Digital Projection Titan 1080p-500, 1080p-250 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 577 Digital Projection manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
July 2007 Page 4.25 Digital Projection TITAN 1080p-500, 1080p-250 User Manual 4. Controlling the projector Notes Horizontal and Vertical Aspect Ratio adjustments are available only when User is selected in Aspect Ratio, (see previous page). Keystone adjustment can be found in both the Geometry and Projector Setup menus. Phase adjustment can be found in both the Picture and Geometry menus, and is available for graphics based RGB sources only. Pixels adjustment is available for graphics based RGB inputs only. User Horizontal Aspect Ratio Press and to select User H Aspect. Press and to adjust the slider (internal number – adjust to fi t). User Vertical Aspect Ratio Press and to select User V Aspect. Press and to adjust the slider (internal number – adjust to fi t). Keystone Used to correct for distortion caused by the projector being mounted higher or lower than the screen. Press and to select Keystone. Press and to adjust the slider (-128 to +127). Phase Phase should be set automatically by the projector, but can be adjusted manually to correct for shimmering or poor quality defi nition on, for example, fi ne text. Press and to select Phase. Press and to adjust the slider (0 to 32). Pixels per line Pixels per line should be set automatically by the projector, but can be adjusted manually to correct for non-standard sources. Press and to select Pixels. Press and to adjust the slider. • • • • • Geometry menu continued
Page 4.26 July 2007 4. Controlling the projector Digital Projection TITAN 1080p-500, 1080p-250 User Manual Blanking Blanking curtains can be applied to each edge of the picture. Press and to select Blanking. Press to open the Blanking submenu. Blanking On/Off Press and to select from: On Off Blanking adjust Press and to select the edge to be Blanked. Press and to adjust the slider (0 to 200). • • • Notes Geometry Menu Blanking The blanking curtains will not applied until Blanking is turned On. The On Screen Display will move to the centre of the DMD when Blanking is turned On. Set to zero for no blanking, eg the top edge in this example. Geometry menu continued
July 2007 Page 4.27 Digital Projection TITAN 1080p-500, 1080p-250 User Manual 4. Controlling the projector Notes When using the menus, press OSD or to hide or reveal the On-Screen-Display. Colour Menu Some menu items may be greyed out - unavailable due to the effect of settings made in other menus, or due to the type of input signal. Read these notes on Colour and Global Colourimetry before making any settings in the Colour menus. Colour menu To return to the main menu, press up to three times. From the main menu: Press and until Colour is highlighted. Press to open the Colour menu. The blue highlight moves to the fi rst item in the menu. • Notes on Colour and Global Colourimetry Global Colourimetry menu (see later in this section, in Setup menu) After a calibration check on the projector or venue, a set of Global colour settings can be made in the Global Colourimetry menu. These settings are then available to be copied at any time using the Colour Mode setting in the Colour menu, or used as a starting point using the Trim feature in the Colour menu. Colour menu (see this section). The settings made in the Colour menu will be automatically saved in the Mode History, or can be manually saved to one of the Input Presets (see Input modes and settings earlier in this section). The selections available in Colour Mode in the Colour menu are: Global Copies the settings made in the Global Colourimetry menu Temperature Set the colour temperature using the slider User Set the Red, Green and Blue Lift and Gain using the sliders Peak Preset high brightness setting
Page 4.28 July 2007 4. Controlling the projector Digital Projection TITAN 1080p-500, 1080p-250 User Manual Notes Read the notes on Colour and Global Colourimetry earlier in this section before making any settings in the Colour menus. The Colour Temperature slider is available only if Temperature Mode is selected. The RGB Lift and Gain sliders are available only if User Mode is selected. The Component Type selection is available for RGB1, RGB2 and Component inputs only. Colour Mode Press and to select Colour Mode. Press and to select from: Global Temperature User Peak Colour Temperature Press and to select Temperature. Press and to adjust the slider (3,000K to 10,000K. in 100 steps). RGB Lift Press and to select the parameter to be adjusted. Press and to adjust the slider. RGB Gain Press and to select the parameter to be adjusted. Press and to adjust the slider. Component Type Press and to select Component Type. Press and to select from: RGB YPrPb • • • • • Colour menu continued
July 2007 Page 4.29 Digital Projection TITAN 1080p-500, 1080p-250 User Manual 4. Controlling the projector Notes The Trim submenu is available only if Global Colour Mode is selected. Colour Menu Trim Read the notes on Colour and Global Colourimetry earlier in this section before making any settings in the Colour menus. Trim Press and to select Trim. Press to open the Trim submenu. Trim RGB Lift and Gain Press and to select the parameter to be adjusted. Press and to adjust the slider (-128 to +127). Global Colourimetry This is a shortcut to the Global Colourimetry submenu, described later in this section, in Setup Menu. Press and to select Global Colourimetry. Press to open the Global Colourimetry submenu. • • • Colour menu continued
Page 4.30 July 2007 4. Controlling the projector Digital Projection TITAN 1080p-500, 1080p-250 User Manual Notes When using the menus, press OSD or to hide or reveal the On-Screen-Display. Setup Menu Setup menu To return to the main menu, press up to three times. From the main menu: Press and until Setup is highlighted. Press to open the Setup menu. The blue highlight moves to the fi rst item in the menu. •
July 2007 Page 4.31 Digital Projection TITAN 1080p-500, 1080p-250 User Manual 4. Controlling the projector Projector Press and to select Projector. Press to open the Projector submenu. Orientation Press and to select Orientation. Press and to select from: Desktop Front Desktop Rear Ceiling Front Ceiling Rear Control Panel Backlight Press and to select Backlight. Press and to select from: On Off Component Video Sync Press and to select Component Video Sync. Press and to select from: Sync On Green Separate • • • • Setup menu, continuedNotes Setup Menu Projector
Page 4.32 July 2007 4. Controlling the projector Digital Projection TITAN 1080p-500, 1080p-250 User Manual Keystone Used to correct for distortion caused by the projector being mounted higher or lower than the screen. Press and to select Keystone. Press and to adjust the slider (-128 to +127). Test Pattern Press and to select Test Pattern. Press to open the Test Pattern submenu. Press and to select from: Off Alignment Grid Screen Layout (shows outlines of various aspect ratios) Chequerboard Colour Bars 0% Field (black) 20% Field 100% Field (white, affected by colour settings) 100% Field (Peak White) (white, unaffected by colour settings) • • Setup menu, Projector continued Notes Setup Menu Test Pattern
July 2007 Page 4.33 Digital Projection TITAN 1080p-500, 1080p-250 User Manual 4. Controlling the projector Notes Setup Menu Global Colourimetry Some menu items may be greyed out - unavailable due to the effect of settings made in other menus, or due to the type of input signal. Read these notes on Colour and Global Colourimetry before making any settings in the Colour menus. Global Colourimetry Press and to select Global Colourimetry. Press to open the Global Colourimetry submenu. • • Setup menu continued Notes on Colour and Global Colourimetry Global Colourimetry menu (see this section) After a calibration check on the projector or venue, a set of Global colour settings can be made in the Global Colourimetry menu. These settings are then available to be copied at any time using the Colour Mode setting in the Colour menu, or used as a starting point using the Trim feature in the Colour menu. Colour menu (see earlier in this section). The settings made in the Colour menu will be automatically saved in the Mode History, or can be manually saved to one of the Input Presets (see Input modes and settings earlier in this section). The selections available in Colour Mode in the Colour menu are: Global Copies the settings made in the Global Colourimetry menu Temperature Set the colour temperature using the slider User Set the Red, Green and Blue Lift and Gain using the sliders Peak Preset high brightness setting
Page 4.34 July 2007 4. Controlling the projector Digital Projection TITAN 1080p-500, 1080p-250 User Manual Notes Read the notes on Colour and Global Colourimetry earlier in this section before making any settings in the Colour menus. The Colour Temperature slider is available only if Temperature Mode is selected. The RGB Lift and Gain sliders are available only if User Mode is selected. Colour Mode Press and to select Colour Mode. Press and to select from: Temperature User Peak Colour Temperature Press and to select Temperature. Press and to adjust the slider (3,000K to 10,000K. in 100 steps). RGB Lift Press and to select the parameter to be adjusted. Press and to adjust the slider. RGB Gain Press and to select the parameter to be adjusted. Press and to adjust the slider. • • • • Setup menu, Global Colourimetry continued