Digital Projection Titan 1080p-500, 1080p-250 User Manual

							July 2007 Page 4.5
Digital Projection TITAN 1080p-500, 1080p-250 User Manual  4. Controlling the projector
Input modes and settings
Input mode detection
The projector can automatically detect the following parameters from the incoming 
video signal:
line frequency
frame rate
interlace / progressive
From these parameters the projector can determine input mode, for example:
 input source  horizontal  vertical     mode
composite 15.73KHz  60.0Hz = NTSC
RGB1 31.51KHz 60.0Hz = SDTV 480p
DVI 64.02KHz 60.0Hz = SXGA 60
When you select a new input source, the green LED near the input connector will 
fl ash, and the searching message will be displayed.
When the input mode has been detected, the LED will show continuously and the 
auto detect message will be displayed, for example:
If the input mode cannot be detected, the LED will continue to fl ash, to show that the 
input is still selected. However, the following message will be displayed:
Mode library and mode history
Once an input mode has been successfully determined for the fi rst time, a set of 
default modal settings (picture, geometry and colour), will be copied from the mode 
library to the mode history. •
•
•
•
•
•
•
Notes
  For a full list of supported input 
modes, see Input modes 
supported, in section 7. 
Appendix.
NTSCmode 
detected Mode 
librarydefaults
SDTV
480p
HDTV
1080p
SVGAdefaults
defaults
defaults
Mode 
history 
						

							Page 4.6 July 2007
4. Controlling the projector  Digital Projection TITAN 1080p-500, 1080p-250 User Manual
Any subsequent changes that you make to the modal settings will be saved in the 
mode history,  with the input mode.
If a new signal is detected, the mode history for the previous signal will be saved in 
the mode history, and the new mode added, along with a new set of default settings. 
Thus the projector builds up a history of input modes, and the required settings for 
each mode, depending on actual useage.
Input presets
It may be the case that you need to save more than one set of modal settings for 
the same input mode. For example you may have more than one video player or a 
selection of fi lms with different characteristics.
In that case, the current input source and modal settings can be saved to any one of 
16 input presets, for recall when the same input source is used again.
When you recell a preset, the projector switches to the saved input source, and 
redetects the input mode before applying the saved modal settings.
Notes
  In normal use, there should be 
adequate  memory to record 
all likely modal settings in the 
mode history.
  However, in exceptional 
circumstances, the least used 
settings will be deleted, to allow 
a new mode to be added.
  A preset can be applied only to 
the same mode for which it was 
created. If the detected input 
mode does not match, then 
settings from the mode history 
or mode library will be applied.
NTSCnew 
modal 
settingsdefaults
SDTV
480p
HDTV
1080p
SVGAdefaults
defaults
defaults
Mode 
history Mode 
library
NTSC
NTSC
new 
mode 
detected
defaults
SDTV
480p
HDTV
1080p
SVGAdefaults
defaults
defaults
Mode 
history Mode 
library
NTSC
settings
DVIsettings
SVGA1) input 
switched 2) mode 
redetected
3) settings 
applied
preset 
saved Mode 
history
NTSC
settings
Input 
presets
SVGA
settingsA
B
C
DRGBsettings DVIsettings
DVISVGA
SDTV 
						

							July 2007 Page 4.7
Digital Projection TITAN 1080p-500, 1080p-250 User Manual  4. Controlling the projector
Indicators
Input status indicators
The indicator next to each input connector on the input panel will light as follows:
 off = input not selected
 green = input selected, signal detected and in range
 fl ashing green  = input selected, but signal not detected or out of range
Notes
  There are more indicators on 
the Control panel, and these are 
described on the next page.
  Input 4. is not used on this 
projector.
5. Composite Video6. S-Video
7. Component1. RGB1
2. RGB2
3. DVI 
						

							Page 4.8 July 2007
4. Controlling the projector  Digital Projection TITAN 1080p-500, 1080p-250 User Manual
The control panel
Keypad layout
The controls on the keypad are identical to those at the top of the remote control, 
and are described on the following pages.
Projector status indicators
The indicators on the control panel are as follows:
Power off = NO POWER
 green = normal RUNNING mode amber = STANDBY mode
Shutter yellow = CLOSED green = OPEN
Error off = NO ERROR
 fl ashing = ERROR (temperature) steady = ERROR (voltage)
IR blue fl ash = Remote control command received
Lamp 1 off = OFF
 fl ashing red = LAMP ERROR green = ON (100%) amber = (80 - 99%)
 fl ashing green/amber  = LAMP COOL-DOWN or WARM-UP
Lamp 2 off = OFF
 fl ashing red = LAMP ERROR green = ON (100%) amber = (80 - 99%)
 fl ashing green/amber  = LAMP COOL-DOWN or WARM-UP
Notes
  Many features are controlled 
from the menus using the menu 
navigation keys on the remote 
control or keypad.
 For more information about 
using the menus, see later in 
this section, Using the menus.
  Some of the menu features, for 
example brightness, contrast 
and input preset operations, can 
be accessed directly using the 
control keys at the bottom of 
the remote control.
  Other features, eg zoom and 
focus, are controlled using the 
control keys at the top of the 
remote control and keypad.
 For more information about 
using the control keys, see 
later in this section, Using the 
control keys.
 The Lamp 2 indicator applies 
only to the 1080p-500. The 
1080p-250 has only one lamp. 
						

							July 2007 Page 4.9
Digital Projection TITAN 1080p-500, 1080p-250 User Manual  4. Controlling the projector
The remote control
Layout
Timeout
There is a 10 second timeout for the three Lens adjustment keys (see note on next 
page).
There is a separate, adjustable timeout for the On Screen Menus (see On Screen 
Display, in Setup Menu, later in this section).
Notes
  Many features are controlled 
from the menus using the menu 
navigation keys on the remote 
control or keypad.
 For more information about 
using the menus, see later in 
this section, Using the menus.
  Some of the menu features, for 
example brightness, contrast 
and input preset operations, can 
be accessed directly using the 
control keys at the bottom of 
the remote control.
  Other features, eg zoom and 
focus, are controlled using the 
control keys at the top of the 
remote control and keypad.
 For more information about 
using the control keys, see 
later in this section, Using the 
control keys.
  The following keys are NOT 
used on this projector:
 CTRL
R P Y
FUNC
10+  (but N is used)
#   (but R is used)
  Note that plugging in the remote 
control cable will disable the 
infra-red.
Menu 
navigation 
keys
Remote control 
backlight
ON/OFFControl keys
Transmit 
indicator 
						

							Page 4.10 July 2007
4. Controlling the projector  Digital Projection TITAN 1080p-500, 1080p-250 User Manual
Notes
  Closing the shutter produces 
a better black than simply 
removing the signal, as the 
light source will be completely 
blocked by the shutter blade.
  When the OSD is OFF:
  -  all menu navigation keys are 
disabled.
  - keys such as 
 BRI 
(brightness) will still function, 
but the slider bars will not be 
visible on screen.
  When any of the three Lens 
adjustment keys is pressed, the 
blue Transmit indicator on the 
remote control will light for 10 
seconds:
  - after 10 seconds, if no 
adjustment has been made, 
the indicator will go out and 
the Lens adjustment key must 
be pressed again to resume 
adjustment.
  - to end the adjustment before 
10 seconds has elapsed, press 
the  
 key.
  - all other adjustments will 
be locked out until the Lens 
adjustment is ended.
  For more information about the 
amount of lens shift available, 
see section 2. Installation.
Using the control keys
Power
Press POWER  and hold for 3 seconds, to switch the projector ON.
Press POWER 
 and hold for 3 seconds, to switch the projector OFF.
Shutter
Press SHUTTER  to OPEN the shutter.
Press SHUTTER 
 to CLOSE the shutter.
On-Screen-Display
Press OSD  to switch the On-Screen-Display OFF.
 This includes ALL menus, controls and on-screen messages.
Press OSD 
 to switch the On-Screen-Display ON.
Focus
Press  followed by  and  to adjust the focus.
When adjustment is fi nished, press 
.
Zoom
Press  followed by  and  to adjust the zoom.
When adjustment is fi nished, press 
.
Shift
Press  followed by , ,  or  to shift the lens up, down, left or 
right.
When adjustment is fi nished, press 
. •
•
•
•
•
•
•
•
• 
						

							July 2007 Page 4.11
Digital Projection TITAN 1080p-500, 1080p-250 User Manual  4. Controlling the projector
Auto-detect input mode
Press  to force the projector to re-detect the input mode
(see Input modes and settings, earlier in this section).
Source information
Press  to display the source information screen.
Input
Press  or   to change to the next input up or down the following list:
1. RGB1
2. RGB2
3. DVI
4. (not used in this projector)
5. Composite Video
6. S-Video
7. Component
Or press the numbered keys 1–7 to change directly to the input:
 
•
•
•
•
Notes
  For more information about 
input mode detection, see 
earlier in this section, Input 
modes and settings.
  Input 4. is not used on this 
projector. 
						

							Page 4.12 July 2007
4. Controlling the projector  Digital Projection TITAN 1080p-500, 1080p-250 User Manual
Notes
  For more information about 
input modes and input presets, 
see earlier in this section, Input 
modes and settings.
  A preset can be applied only to 
the same mode for which it was 
created. If the detected input 
mode does not match, then 
settings from the mode history 
or mode library will be applied.
  For more information about 
input modes, see Input modes 
and settings. earlier in this 
section.
Input Presets
Recall
To recall a set of modal settings that have been saved, press and hold , 
whilst pressing the lettered key 
 A – S.
 The projector will switch to the saved input source, and redetect the input mode 
before applying the saved modal settings.
Save
To save the current input source, mode and modal settings, press and hold 
, whilst pressing the lettered key  A – S.
 If this Preset has been used before, and the Input source has been changed, 
then the following  message will be displayed.
 Press 
 and   to select either OK or Cancel.
 Press 
 to confi rm your selection.
 The modal settings will be saved to the selected preset, and the following 
message will be displayed. •
•
•
•
•
• 
						

							July 2007 Page 4.13
Digital Projection TITAN 1080p-500, 1080p-250 User Manual  4. Controlling the projector
Notes
  The red, green and blue keys 
are disabled when the OSD is 
switched OFF.
 The Saturation control is 
available for Composite, S-
Video and Component inputs 
only.
 The Phase control is available 
for RGB inputs only.
  For all adjustments on this page 
that require more than one key 
to be pressed:
  - after 10 seconds, if no 
adjustment has been made,  the  
 key must be pressed again 
to resume adjustment.
  - to end the adjustment before 
10 seconds has elapsed, press 
a different adjustment key, or 
press the  
 key.
  When the OSD is OFF:
 - the 
 keys will still function, 
but the controls will not be 
visible on screen.
Red, Green and Blue
Press ,  or   to switch the red, green or blue components OFF 
or ON.
Test pattern
Press  to select a test pattern.
Picture settings
Press a  key, followed by  and   to adjust these picture settings:
Brightness  
 BRI
Contrast  
 CON
Saturation  
 SAT
Phase  
 PHASE
Aspect ratio   
 ASPECT
Geometry settings
Keystone adjustment is used to correct for distortion caused by the projector being 
mounted higher or lower than the screen.
Press Keystone 
 KEYST,
followed by 
 and  to adjust the keystone correction:
Press Position  
 POS,
followed by 
, ,  and  to adjust the picture position, for images 
smaller than the DMD: •
•
•
•
• 
						

							Page 4.14 July 2007
4. Controlling the projector  Digital Projection TITAN 1080p-500, 1080p-250 User Manual
Notes
  The magnify feature utilises a 
digital zoom. Used with the pan 
control, this can be used to:
  - enlarge a section of the image
  - enable the use of multiple 
projectors to construct a large 
image from tiles.
  The pan control is available 
only when the image has been 
magnifi ed.
  If the OSD moves off screen 
due to a change in image size, 
then pressing the size key will 
restore its readability.
  When fresh batteries are 
inserted in the remote control 
it will default to address 00. 
Remote control 00 is a master 
control,  able to control all 
projectors.
  If two or more projectors are set 
to the same address, they can 
be controlled from one remote 
control, provided they are 
connected by cable or in range 
of the infra red.
Magnify and pan
Press Magnify  MAGNIFY
followed by 
 and  to adjust the size of the picture.
Press Pan   
 PA N
followed by 
, ,  and  to adjust the position of the magnifi ed image.
On-screen-display size
Press Size    SIZE
to switch the size of the OSD between large and small.
Remote control address
The projector and the remote control need to be set to matching addresses. Read 
the note to the right on this page, and follow the instructions in the order shown 
below:
1  Set the projector address as shown in Setup menu, later in this section.
2  Set the remote control address:
Press and hold 
 
whilst pressing two numbered keys 
 0 – 9
to set the remote control address to any number between 00 and 99.
(leading zeros must be used for numbers less than 10)
Remote control backlight
Press  to switch the backlight on and off. •
•
•
•
•