Digital Projection Titan 1080p-500, 1080p-250 User Manual

July 2007 Page 4.15
Digital Projection TITAN 1080p-500, 1080p-250 User Manual  4. Controlling the projector
Notes
  Some  menu controls can be 
accessed directly using the 
control keys (see earlier in this 
section).
  When the OSD is OFF, all menu 
navigation keys will be disabled.
  When the OSD is switched back 
ON, the menus will remain OFF 
until the  
 key is pressed 
again. The menus will then 
reopen at the same point they 
were last viewed.
  If a menu is opened, and no 
other key is pressed...

Page 4.16 July 2007
4. Controlling the projector  Digital Projection TITAN 1080p-500, 1080p-250 User Manual
Press  to open the menu. The blue highlight moves to the fi rst item in the 
menu, which may be submenu, for example the Projector Setup submenu.
To select a submenu, press 
 and  , for example the Lamp submenu.
Press 
 to open the submenu. The submenu opens, with the title at the top.
To close the submenu and return to the previous level, press 
.
There may be up to three levels of submenu, so to...

July 2007 Page 4.17
Digital Projection TITAN 1080p-500, 1080p-250 User Manual  4. Controlling the projector
Slider bar
The highlighted slider bar shows which 
control is active currently.
To adjust the slider press 
 and .
Parameter selection
To select from a number of parameters, 
(shown one at a time to the right), 
press 
 and .
These two items are greyed out and 
the values are blank, showing that they 
are not available, due to the effect of 
settings made in other menus, or due 
to the type of...

Page 4.18 July 2007
4. Controlling the projector  Digital Projection TITAN 1080p-500, 1080p-250 User Manual
Input menu
  To return to the main menu, press  up to three times.
 From the main menu:
Press 
 and   until Input is highlighted.
Press 
 to open the Input menu. The blue highlight moves to the fi rst item in 
the menu. The 
 symbol shows which input is currently selected.
Input Source
Press  and   to select from:
1. RGB1
2. RGB2
3. DVI
4. (not used in this projector)
5. Composite Video
6. S-Video...

July 2007 Page 4.19
Digital Projection TITAN 1080p-500, 1080p-250 User Manual  4. Controlling the projector
Notes
  Some  menu controls can be 
accessed directly using the 
control keys (see earlier in this 
section).
  For more information about 
input modes and input presets, 
see earlier in this section, Input 
modes and settings.
Input Menu
 Presets
Input Menu
 Presets
    Recall Presets A ~ H
Presets
Sixteen sets of parameters can be saved and recalled (A – S). The parameters 
saved for each Preset...

Page 4.20 July 2007
4. Controlling the projector  Digital Projection TITAN 1080p-500, 1080p-250 User Manual
Notes
  Some  menu controls can be 
accessed directly using the 
control keys (see earlier in this 
section).
Input Menu
 Presets
    Save Presets A ~ H Save Presets
Press  and   to select Save Preset.
 Press 
 to open the Save Presets A ~ H submenu.
To save the current set of parameters, press 
 and   to select one of the 
Presets.
 For Presets J to S, select Save Preset J ~ S then press 
 to open...

July 2007 Page 4.21
Digital Projection TITAN 1080p-500, 1080p-250 User Manual  4. Controlling the projector
Notes
  Some  menu controls can be 
accessed directly using the 
control keys (see earlier in this 
section).
  When using the menus, press 
OSD 
 or  to hide or 
reveal the On-Screen-Display.
Picture Menu
  Some menu items may be 
greyed out - unavailable due to 
the effect of settings made in 
other menus, or due to the type 
of input signal.
 The Saturation slider is 
available for Composite,...

Page 4.22 July 2007
4. Controlling the projector  Digital Projection TITAN 1080p-500, 1080p-250 User Manual
Notes
  For more information about 
User gamma settings, see 
section 5. DP Userware.
 Parametric Gamma adjustment 
is available only when 
Parametric is selected in 
Gamma selection, above.
 Phase adjustment can be 
found in both the Picture and 
Geometry menus, and is 
available for RGB1 and RGB2 
inputs only.
Gamma Correction
Video recordings are often supplied with a gamma adjustment applied....

July 2007 Page 4.23
Digital Projection TITAN 1080p-500, 1080p-250 User Manual  4. Controlling the projector
Notes
 Aspect Ratio selection can be 
found in both the Picture and 
Geometry menus.
 When User Aspect is selected, 
the Aspect Ratio settings are 
taken from the User H Aspect 
and V Aspect settings made in 
the Geometry menu.
 The Sharpness slider is 
available for Composite, 
S-Video and Component SD 
inputs only.
Aspect Ratio
Press  and   to select Aspect Ratio.
 Press 
 and   to select from:...

Page 4.24 July 2007
4. Controlling the projector  Digital Projection TITAN 1080p-500, 1080p-250 User Manual
Notes
  Some  menu controls can be 
accessed directly using the 
control keys (see earlier in this 
section).
  When using the menus, press 
OSD 
 or  to hide or 
reveal the On-Screen-Display.
Geometry Menu
  Some menu items may be 
greyed out - unavailable due to 
the effect of settings made in 
other menus, or due to the type 
of input signal.
 Aspect Ratio selection can be 
found in both the...