Digital Projection Titan 1080p-500, 1080p-250 User Manual

July 2007 Page 2.9
Digital Projection TITAN 1080p-500, 1080p-250 User Manual  2. Installation
Notes
  This chart has a TRF of 1.33, 
for use with the following 
images:
4:3 = 1.33
Lens charts continued
Full height image 4:3
Use the chart below to choose which lens best suits your application.
if you need to be more precise, then use the calculations on the page immediately 
following the lens charts.
1.12 : 1 fi xed lens
(1.2 - 2m)
105-609
105-6091.39 - 1.87 : 1 
zoom lens
105-610
107-1961.87 - 2.56 : 1...

Page 2.10 July 2007
2. Installation  Digital Projection TITAN 1080p-500, 1080p-250 User Manual
Notes
  This chart has a TRF of 1.42, 
for use with the following 
images:
5:4 = 1.25
Lens charts continued
Full height image 5:4
Use the chart below to choose which lens best suits your application.
if you need to be more precise, then use the calculations on the page immediately 
following the lens charts.
1.12 : 1 fi xed lens
(1.2 - 2m)
105-609
105-6091.39 - 1.87 : 1 
zoom lens
105-610
107-1961.87 - 2.56 : 1...

July 2007 Page 2.11
Digital Projection TITAN 1080p-500, 1080p-250 User Manual  2. Installation
Notes
  The Throw ratio for a particular 
lens is fi xed, and assumes that 
the image fi lls the width of the 
DMD.
  For images that do not fi ll the 
width of the DMD, the Throw 
ratio is effectively increased. To 
correct for this, a Throw Ratio 
Factor (TRF) is used.
Choosing a lens by calculation
For any screen size not listed above, or if you need to be more precise, then use the 
calculations below....

Page 2.12 July 2007
2. Installation  Digital Projection TITAN 1080p-500, 1080p-250 User Manual
Notes
  The Throw ratio for a particular 
lens is fi xed, but assumes that 
the image fi lls the width of the 
DMD.
  For images that do not fi ll the 
width of the DMD, the Throw 
ratio is effectively increased. To 
correct for this, a Throw Ratio 
Factor (TRF) is used.
  Lens extension is measured 
when the lens is focused at 
infi nity, and fully extended. 
At other focus settings, the 
extension could be up to...

July 2007 Page 2.13
Digital Projection TITAN 1080p-500, 1080p-250 User Manual  2. Installation
Notes
  Make sure the rear lens cap is 
removed, before fi tting the lens.
  Make sure the front lens cap is 
removed, before switching on 
the projector.
  Be careful not to scratch 
the lens surfaces. If you do 
accidentally touch a lens, then 
clean the surface using a lens 
paper.
 The lens release lever should 
always be set to the locked 
position to prevent the lens 
from falling out.
Zoom drive...

Page 2.14 July 2007
2. Installation  Digital Projection TITAN 1080p-500, 1080p-250 User Manual
Notes
  For more information on using 
the Lens shift feature, see 
section 4. Using the menus, 
Lens menu.
  If the lens is to be shifted in 
two directions combined, the 
maximum range is somewhat 
less, as can be seen below. 
(zoom lens shift shown).
full horizontal and vertical shift
without distortion
combined shift without distortion
is reduced
Shifting the image
The normal position for the projector is...

July 2007 Page 2.15
Digital Projection TITAN 1080p-500, 1080p-250 User Manual  2. Installation
Mounting the projector
The projector is designed to be used on a fl at surface, but the optional rigging frame 
will allow it to be suspended from a lighting truss or rigging. The four adjustable feet 
under the chassis allow the projector to be lowered onto a fl at surface without any 
danger of hands being trapped between the bottom frame and the surface.
Chassis adjustment
If the projector is to be operated...

Page 2.16 July 2007
2. Installation  Digital Projection TITAN 1080p-500, 1080p-250 User Manual
Adjusting the rigging frame
Coarse adjustment of projector level should be made by adjusting the length of 
the supporting wires or chains, or by adjusting the position of the truss or rigging. 
Once the initial coarse adjustment has been made, fi ne adjustment can be made by 
turning the frame adjusters on the rigging frame:
The single vertical adjuster at the front left corner is used to 
raise or lower the...

July 2007 Page 2.17
Digital Projection TITAN 1080p-500, 1080p-250 User Manual  2. Installation
Notes
 When stacking projectors, 
the stack MUST be vertical, 
to ensure that the stresses 
are distributed to all frame 
couplings.
 Make sure that the surface, 
ceiling or rigging that is 
to support the projector is 
capable of supporting the 
combined weight of all the 
projectors and lenses (see 
specifi cation for weights).
 Do not place heavy objects 
on top of the projector 
chassis. Only the chassis...

Page 2.18 July 2007
2. Installation  Digital Projection TITAN 1080p-500, 1080p-250 User Manual
Notes
  For more information on 
selecting an input source, see 
section 4. Overview, Using 
the control keys, and Using 
the menus.
  Input 4. is not used on this 
projector.
 
 For more information about pin 
connections and control codes 
see section 7. Appendix.
  For more information on 
input modes see section 
4. Overview.
Connecting the projector
Signal Inputs
The following inputs are available:
EDID...