Digital Projection Titan 1080p-500, 1080p-250 User Manual

July 2007 Page 4.45
Digital Projection TITAN 1080p-500, 1080p-250 User Manual  4. Controlling the projector
Notes
 Restore Defaults will restore 
all settings to factory 
defaults.
  If you are not sure this is 
what you want to do, then 
either:
 make a record of all settings 
fi rst
or
select No, then press 
.
  Following a restore to factory 
defaults, the projector will 
perform a self-test and enter 
Standby mode.
  This process will take up to 10 
seconds. During this time the 
projector will not...

Page 4.46 July 2007
4. Controlling the projector  Digital Projection TITAN 1080p-500, 1080p-250 User Manual
Notes
  When using the menus, press 
OSD 
 or  to hide or 
reveal the On-Screen-Display.
Information Menu
Information Menu
 Projector Information
 The Lamp 2 information applies 
only to the 1080p-500. The 
1080p-250 has only one lamp.
Information Menu
 Source Information
Information menu
  To return to the main menu, press  up to three times.
 From the main menu:
Press 
 and   until Information is...

July 2007 Page 4.47
Digital Projection TITAN 1080p-500, 1080p-250 User Manual  4. Controlling the projector
Digital Projection Information
Press  and   to select Digital Projection.
 Press 
 to see the DP Information screen. •
Information menu continuedNotes
  When using the menus, press 
OSD 
 or  to hide or 
reveal the On-Screen-Display.
Information Menu
  DP Contact Information 

Page 4.48 July 2007
4. Controlling the projector  Digital Projection TITAN 1080p-500, 1080p-250 User Manual 

July 2007  Page 5.1
5. Userware
Contents 

Page 5.2 July 2007
5. Userware  Digital Projection TITAN 1080p-500, 1080p-250 User Manual 

July 2007  Page 6.1
6. Maintenance
Contents
Changing the lamp module .............................................................................................................. 6.2
Changing the air fi lter ........................................................................................................................ 6.3
Cleaning ................................................................................................................................................ 6.4
Projector...

Page 6.2 July 2007
6. Maintenance  Digital Projection TITAN 1080p-500, 1080p-250 User Manual
Changing the lamp module
Turn the power OFF and allow the lamp to cool for 5 minutes.
Unscrew the three door screws, and detach the rear door - the door is tethered, 
so cannot be removed completely.
Disconnect the timer cable from the lamp module.
Loosen the two captive fi nger screws securing the lamp module.
Pull the lamp module to the right, then to the rear to remove it from the projector.
Insert a new lamp...

July 2007 Page 6.3
Digital Projection TITAN 1080p-500, 1080p-250 User Manual  6. Maintenance
Changing the air fi lter
Turn the power OFF and allow the lamp to cool for 5 minutes.
Unscrew the three door screws, and remove the rear door.
Pull out the air fi lter.
Fit a new air fi lter.
Re-fi t the rear door, making sure that the door tether is not trapped, and tighten 
the three screws. •
•
•
•
•
Notes
 Always allow the lamp to cool 
for 5 minutes before:
 - disconnecting the power
- moving the projector
-...

Page 6.4 July 2007
6. Maintenance  Digital Projection TITAN 1080p-500, 1080p-250 User Manual
Notes
 Never use strong detergents 
or solvents such as alcohol 
or thinners to clean the 
projector and lens.
 NEVER touch the lamp or 
refl ector.
Cleaning
Turn the projector off before cleaning.
Projector
Clean the cabinet periodically with a damp cloth. If heavily soiled, use a mild 
detergent.
Lens
Use a blower or lens paper to clean the lens, taking care not to scratch the glass.
Lamp module
Use a blower or...