Digital Projection Showlite 5000sx+ Lcd Projector Users Manual

2-13
2. Installation
Connecting the Supplied Power Cable
Connect the supplied power cable to the projector.
First connect the supplied power cables three-pin plug to the AC IN of the projector, and then connect the other plug of the supplied power cable in the
wall outlet.
AUDIO
AU
D
IO O
U
T
R
R/Cr
G/Y
B/Cb
V
H
/
H
V
RL
/
M
O
N
O
RL
/
M
O
N
ORL
/
M
O
N
O L
/
M
O
N
O
DVI
R
G
B
 O
U
T
RGB 1RGB 2AUDIOS
LO
T
 1SL
O
T
 2
VIDEOS-VIDEO
P
C
 C
O
N
T
R
O
L
I
N
IN O
U
T
O
U
T S
C
 TR
IG
G
E
RR
E
M
O
T
E
 2 R
E
M...

3
Projecting an Image
(Basic Operation)
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
z Turning on the Projector............................................. 3-2
x Selecting a Source ................................................... 3-3
c Adjusting the Picture Size and Position .................... 3-3
v Correcting the Horizontal and
Vertical Keystone Distortion (DigiScale - 3D Reform)3-4
b Optimizing RGB Picture Automatically....................... 3-6
n Turning Up or Down Volume...

3-2
3. Projecting an Image
This chapter describes how to turn on the projector and to project a pic-
ture onto the screen.
z Turning on the Projector
NOTE:
•When plugging in or unplugging the supplied power cable, make sure that the
main power switch is pushed to the off[O] position. Failure to do so may cause
damage to the projector.
•The projector has two power switches: main power switch and POWER button
(POWER ON and OFF on the remote control)
•The projector has a feature to prevent itself from being...

3-3
3. Projecting an Image
x Selecting a Source
Selecting the computer or video source
Using the Remote Control
Press the Source/Number button (0-9) to se-
lect input.
1...... RGB 1 input
2...... RGB 2 input
3...... DVI (DIGITAL) input
4...... VIDEO input
5...... S-VIDEO input
6...... Viewer
7...... LAN
8...... SLOT 1
9...... SLOT 2
0...... Sequentially selects:
RGB1 (VIDEO) → RGB2 (S-VIDEO) →
RGB1 (VIDEO) ........
NOTE: If no input signal is available, the projector will display a blue...

3-4
v Correcting the Horizontal and Vertical Key-
stone Distortion (DigiScale - 3D Reform)
Use the DigiScale - 3D Reform feature to correct keystone (trapezoidal)
distortion to make the top or bottom and the left or right side of the screen
longer or shorter so that the projected image is rectangular.
In the following description, DigiScale - 3D Reform (Cornerstone) correc-
tion can be done with the USB mouse, remote control or cabinet buttons.
When using the USB mouse connected to the projector...

3-5
3. Press the 3D REFORM button on the projector cabinet or the KEY-
STONE button on the remote control.
The Cornerstone adjustment screen is displayed.
The Cornerstone adjustment screen will disappear when you move the
USB mouse cursor.
4. Point to one of the remaining 3 corners and left-click on it.
Screen
5. Do the above step 4 for the other two corners so that the projected area
becomes smaller than the screen.
Screen
Left-click on each corner.
Left-click on the corner.
Screen
Projected image
(The...

3-6
The confirmation screen is displayed.
On the Cornerstone adjustment screen, select
“Exit” and then “OK”, or press the CANCEL but-
ton on the remote control. 8. Use the SELECT 

 button to select another icon which points in
the direction.
Screen
9. Press the SELECT 
 or  button to highlight the [OK] and press the
ENTER button.
This completes the keystone correction.
Selecting “Cancel” will return to the adjustment screen without saving
changes (Step 3).
Selecting Reset will return to the factory...

3-7
m Turning off the Projector
To turn off the projector:
First press the POWER (ON/STAND BY) button on the projector cabinet
or the POWER OFF button on the remote control for a minimum of two
seconds. The POWER indicator will glow orange. After the projector turns
off, the cooling fans keep operating for 90 seconds (2 minutes in the op-
tional Long Life lamp 001-716) (Cooling-off time).
Second, turn off the Main Power switch. The power indicator will go out.
Last unplug the power cable.
NOTE: You...

4
Convenient Features
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
z Turning Off the Image and Sound ............................. 4-2
x Enlarging and Moving a Picture ................................ 4-2
c Getting the On-line Help and Information ................. 4-2
v Using a USB Mouse ................................................. 4-3
b Using a USB HUB Function ...................................... 4-3
n Changing Background Logo ..................................... 4-4
m Making Freehand Drawings on...

4-2
z Turning Off the Image and Sound
Press the MUTE PICTURE button to turn off the image and sound for a
short period of time. Press again to restore the image and sound.
x Enlarging and Moving a Picture
You can enlarge the area you want up to 400 percent.
To  do so:
Press the MAGNIFY button.
Enlarge the selected area.
When the MAGNIFY (+) button is pressed, the image is magnified. To
move the magnified image, use the SELECT button.
c Getting the On-line Help and Information
You get the contents about...