Digital Projection Showlite 3000sx, 4000gv User Manual

Lamp Off Mode - Activating this feature allows an RGB  signal to be passed
through to the monitor output connector during a standby condition.
Last Memory- The projector stores the last signal data in memory for each input
(RGB 1, RGB 2, DVI-DIGITAL, Video and S-Video). This feature reduces the
switching time between sources.
If a commercially available switcher is connected, turning on this feature may cause
the image to be displayed incorrectly. If this should happen, turn this feature off to
mute the...

SETUP PAGE 5
Communication Speed- Defines the baud rate of the PC CONTROL connector.
Projector ID- Each projector needs its own unique address when used in serial 
communication mode (multiple projector use). To set the projector ID, select Enable
then select the ID number from the spin box. To activate the setting, select OK.
Default Source Select- You can set the projector to default to last input used, a
pre-defined input or to automatically detect an active source on any input connector. 
When set to...

SETUP PAGE 6
Clear Lamp Hour Meter- Resets the lamp clock to zero. Selecting this option 
displays a confirmation window:  To reset the lamp usage hour, press ÔOKÕ.
The projector will turn off and go into standby mode after 1600 hours (up to 2100
hours in Eco mode) of service. If this happens, press the ÔHelpÕ button on the
remote control for ten seconds to reset the lamp clock to zero. 
Only reset the lamp clock after replacing the lamp.
Clear Filter Usage- Resets the filter usage to zero. It is...

Link Mode 
This feature is used for multiple projector connection using RGB Digital
Input/Output connectors. When using Link Mode, the master projector should be set
to Master and all other projectors set to Slave. For single projector operation,
Standalone should be selected.
Link Mode is not available for DVI Digital.
CÑ42
System Operation
OPERATION
LBV00073; Revision A - 11/01/2002
- 

The Help menu on the SHOWlite 3000sx projector provides three options -
Contents, Source Information and Projector Information.
Contents
The Contents option provides a list of functions for which online help is available.
Underlined functions provide a direct link to the corresponding item by selecting
the option and pressing Enter.
The Help Menu may not be displayed correctly when a UXGA signal is displayed.
Source Information
The Source Information option provides three pages of information about the...

Page 1 User Name, Remaining Lamp Time, Lamp Hour Meter, Filter Usage,
Projector Usage, Projector ID.
Page 2 Version (BIOS/Firmware/Data/SUB-CPU)
Page 3 FPGA Version (OSD/JOE)
Page 4 Link Mode (Master/Slave)
PAGE 4
When you select Page 4 the current status of Link Mode will be displayed. This
window provides the following information.
Master ID- Displays the ID number of the master projector.
Status- Displays the status of the master projector.
Connected PJ- Shows the number of slave projectors...

Seven internal Test Patterns are provided to assist with projector setup and 
alignment. The Test Patterns are selected from a flyout list and for each pattern you
have the ability to turn off the Red, Green and Blue channels.
CÑ45
System Operation
Test Pattern - SHOWlite 3000sx
OPERATION
LBV00073; Revision A - 11/01/2002 

The menu system can be customised to meet individual requirements. Selecting a
menu item from the ÔBasic/Custom Menu EditÕ list allows you to custom tailor the
menu items to your needs.
1. Select ÔBasic/Custom Menu EditÕ to display the editing screen.
2. Use the up and down cursors to highlight your selection and press the Enter 
button to place a check mark next to an option to enable that feature in the menu 
system. Pressing the Enter button over a checked box will deselect it. If you 
select an item...

Up to 12 main menu items (within ÔBasic/Custom Menu EditÕ, not including sub
menu items) can be selected.
3. In order for the changes to take effect, use the left and right cursor buttons to 
highlight ÔOKÕ and press the Enter button. To cancel the changes, use the up or 
down arrows to highlight ÔCancelÕ and press the Enter button. To return to the 
factory default, select ÔResetÕ and press Enter.
The default Basic/Custom Menu items are Source Select (RGB 1/2, DVI DIGITAL,
Video 1/2, S-Video and Entry...

1. RGB 1
2. RGB 2
3. Video 1
4. Video 2
5. S-Video
6. DVI (DIGITAL)
7. DVI (ANALOG)
8. PC Card Viewer
more
Entry List
Brightness / Contrast / Color / Hue / Sharpness
Volume
Keystone
Color Temperature
Lamp Mode
Gamma Correct
Advanced Options
Factory DefaultSwitcher
Entry List
RGB1 (Video)
RGB1 (S-Video)
RGB2 (Video)
RGB2 (S-Video)
Timer
Menu
Setup
Link Mode
Switcher Control
LAN Mode (optional)
Capture
PC Card File
Contents
Information Advance Menu
Source Select
Picture
Volume
Image Options
Projector...