Digital Projection M-vision Cine Led User Manual

Rev B December 2010 Page 4.3
Digital Projection M-Vision Cine LED User Manual 4. Controlling the projector

Overview
Controlling the projector
The projector can be controlled from:
the remote control
the projector control panel
the RS232 input
For more information about controlling the projector using the RS232 inp\
ut, see 
Remote communications protocol in section 6. Appendix.
For information about how to connect the projector, see Connecting the 
projector in section 2. Installation, and Connections...

Page 4.4 Rev B December 2010
4. Controlling the projector Digital Projection M-Vision Cine LED User Manual

The control panel
The projector control panel is designed to be read in both table top or \
ceiling 
orientation, for ease of use.
The menu navigation keys are similar to those on the remote control, and\
 are 
described in detail in Using the menus, later in this section.
POWER  Press this once to switch the projector ON or twice to switch it to 
STANDBY mode.
SOURCE  Press this repeatedly to...

Rev B December 2010 Page 4.5
Digital Projection M-Vision Cine LED User Manual 4. Controlling the projector

The remote control
Layout
Timeout
There is a 5 second timeout for the control keys at the bottom of the remote control:
- after 5 seconds, if no adjustment has been made, the indicator will go\
 out and 
the adjustment key must be pressed again.
- to end the adjustment before 5 seconds has elapsed, press a different 
adjustment key, or press the key again.
There is a 30 second timeout for the menu...

Page 4.6 Rev B December 2010
4. Controlling the projector Digital Projection M-Vision Cine LED User Manual

Notes
 Note that the blue POWER 
indicator light will be OFF 
when the projector is in normal 
RUNNING MODE.
 For more information about the 
sources programmed into the 
SOURCE keys, see Control 
menu later in this section, 
Using the menus. 
 For more information about 
the Aspect ratio settings, 
see Screen requirements in 
section 2. Installation.
 For more information about 
the settings...

Rev B December 2010 Page 4.7
Digital Projection M-Vision Cine LED User Manual 4. Controlling the projector

Image quality settings
Press any of the following keys on the remote control, followed by  and , to 
adjust these image quality settings:
 Brightness   
Contrast   
Sharpness   
Gamma   
Overscan   
Noise reduction 
Brilliant-color   
Colour temperature 
Example - Brightness screen control:
Test pattern
Press the  key repeatedly to cycle through the Test patterns, in the 
following order:
White,...

Page 4.8 Rev B December 2010
4. Controlling the projector Digital Projection M-Vision Cine LED User Manual

Notes
 Some  menu controls can be 
accessed directly using the 
control keys (see earlier in this 
section).
 There is a 30 second timeout 
for the menu navigation keys. If 
a menu times out, simply press 
the Menu key again.
 The SELECT key on the 
projector control panel has 
exactly the same funtion as 
the ENTER key on the remote 
control.
 To exit from the menus 
completely, you may need to...

Rev B December 2010 Page 4.9
Digital Projection M-Vision Cine LED User Manual 4. Controlling the projector

Notes
 To select a different menu, 
press MENU  once or 
twice, so that no items are 
highlighted, then use the the 
 and  keys to select a 
different page.
 To exit from the menus 
completely, you may need to 
press  up to three times.
 Image changes made using 
the menus will take effect 
immediately.
 Some menu items may be 
greyed out - unavailable due to 
the effect of settings made in 
other...

Page 4.10 Rev B December 2010
4. Controlling the projector Digital Projection M-Vision Cine LED User Manual

Presets
Press ENTER or SELECT.
The Presets submenu will appear:
Use the  and  keys to select from:
Recall Presets
Save Presets
recall presets
Recall a set of image settings that have previously been saved to Preset\
s A, B, 
C or D.
Use the  or  keys to select which Preset is to be recalled. 
 Select Default, to recall the factory default settings.
Save presets
Save the the image settings for all...

Rev B December 2010 Page 4.11
Digital Projection M-Vision Cine LED User Manual 4. Controlling the projector

Brightness
Press  or  once. 
After the first press, the Brightness adjustment bar will appear:
Use the  and  keys to adjust the Brightness from 0 to 200:
To return to the Main menu, press  once.
Contrast
Press  or  once. 
After the first press, the Contrast adjustment bar will appear.
Use the  and  keys to adjust the Contrast from 0 to 200:
To return to the Main menu, press  once.
Saturation...

Page 4.12 Rev B December 2010
4. Controlling the projector Digital Projection M-Vision Cine LED User Manual

Notes
 To exit from the menus 
completely, you may need to 
press  up to three times.
 Image changes made using 
the menus will take effect 
immediately.
 Some menu items may be 
greyed out - unavailable due to 
the effect of settings made in 
other menus, or due to the type 
of input signal.
 When the Aspect Ratio is set 
to Native, Overscan can only 
be set to Off or Crop
Sharpness
Press  or...