Digital Projection M-vision Cine Led User Manual

							
Rev B December 2010 Page 4.3
Digital Projection M-Vision Cine LED User Manual 4. Controlling the projector

Overview
Controlling the projector
The projector can be controlled from:
the remote control
the projector control panel
the RS232 input
For more information about controlling the projector using the RS232 inp\
ut, see 
Remote communications protocol in section 6. Appendix.
For information about how to connect the projector, see Connecting the 
projector in section 2. Installation, and Connections in section 6. Appendix.
Many features are controlled from the menus using the menu navigation ke\
ys on 
the remote control or the projector control panel.
For more information about using the menus, see later in this section, Using the 
menus.
Some of the menu features, for example brightness, contrast and sharpnes\
s, 
can be accessed directly using the control keys at the bottom of the rem\
ote 
control.
•
•
•
•
•
Notes 
						

							
Page 4.4 Rev B December 2010
4. Controlling the projector Digital Projection M-Vision Cine LED User Manual

The control panel
The projector control panel is designed to be read in both table top or \
ceiling 
orientation, for ease of use.
The menu navigation keys are similar to those on the remote control, and\
 are 
described in detail in Using the menus, later in this section.
POWER  Press this once to switch the projector ON or twice to switch it to 
STANDBY mode.
SOURCE  Press this repeatedly to cycle through the input sources, in the 
following order:
  HDMI 1, HDMI 2, RGB, Component 1, Component 2, Video, 
S-Video, HDMI 1...
 If you select a source that IS connected and active, the projector 
will automatically adjust to the  parameters of the signal, and 
display it.
 If you select a source that is NOT connected or active, the 
projector will continue searching through the input sources until it 
finds a valid signal.
LED status indicators
The indicators on the control panel are as follows:
POWER off = NO POWER or normal RUNNING mode
 steady blue = STANDBY mode
 flashing blue = WARM-UP or  COOL-DOWN mode
ISSUE off = NO ERROR flashing or steady red = ERROR
Notes
 Many features are controlled 
from the menus using the menu 
navigation keys on the remote 
control or the projector control 
panel.
 For more information about 
using the menus, see later in 
this section, Using the menus.
 If the red ISSUE indicator is 
illuminated continuously or 
flashing, see Error Codes in 
section 6.  Appendix, for more 
information
Menu 
navigation 
keys 
						

							
Rev B December 2010 Page 4.5
Digital Projection M-Vision Cine LED User Manual 4. Controlling the projector

The remote control
Layout
Timeout
There is a 5 second timeout for the control keys at the bottom of the remote control:
- after 5 seconds, if no adjustment has been made, the indicator will go\
 out and 
the adjustment key must be pressed again.
- to end the adjustment before 5 seconds has elapsed, press a different 
adjustment key, or press the key again.
There is a 30 second timeout for the menu navigation keys.
Menu 
navigation 
keys
Control keys
Transmit 
indicator
Notes
 Many features are controlled 
from the menus using the menu 
navigation keys on the remote 
control or the projector control 
panel.
 For more information about 
using the menus, see later in 
this section, Using the menus.
 Some of the menu features, 
for example brightness, 
contrast and sharpness, can 
be accessed directly using the 
control keys at the bottom of 
the remote control.
 For more information about 
using the control keys, see 
later in this section, Using the 
control keys.
 In most situations, you can 
simply point the remote control 
at the screen which will reflect 
the IR signal from the remote 
back toward the receiver on the 
projector.
  In some cases, however, 
ambient conditions may prevent 
this. In this case, point the 
remote control directly at the 
projector.
Remote reception angle
40°
40° 
						

							
Page 4.6 Rev B December 2010
4. Controlling the projector Digital Projection M-Vision Cine LED User Manual

Notes
 Note that the blue POWER 
indicator light will be OFF 
when the projector is in normal 
RUNNING MODE.
 For more information about the 
sources programmed into the 
SOURCE keys, see Control 
menu later in this section, 
Using the menus. 
 For more information about 
the Aspect ratio settings, 
see Screen requirements in 
section 2. Installation.
 For more information about 
the settings programmed into 
the USER MEMORY keys, 
see Control menu later in this 
section.
  Note: User memory D is 
available only through the 
Control menu.
Using the control keys
Power
Press POWER ON  on the remote control to switch the projector ON.
The power indicator on the control panel will flash blue for approximate\
ly 30 
seconds, whilst the projector initialises. When the projector is ready f\
or use, the 
power indicator will switch off.
Press POWER OFF  on the remote control to switch the projector to 
STANDBY mode.
Press the button a second time to confirm your intention to switch to ST\
ANDBY 
mode.
The LED module will switch off, and the power indicator on the control panel will 
flash blue for approximately 30 seconds until the projector has cooled d\
own. 
Wait until the power indicator shows steady blue. The projector will now be in 
STANDBY mode.
Source
To switch to one of the five sources programmed into the SOURCE buttons, \
then 
select using the  to   keys.
 If you select a source that IS connected and active, the projector will 
automatically adjust to the  parameters of the signal, and display it.
 If you select a source that is NOT connected or active, the projector will continue 
searching through the input sources until it finds a valid signal, in th\
is order.
HDMI 1, HDMI 2, RGB, Component 1, Component 2, Video, S-Video, HDMI 1...
Aspect ratio
Press  repeatedly to cycle through the Aspect ratio settings, in the 
following order:
16:9, Theaterscope, 4:3, 4:3 Narrow, Native, 16:9...
User memory
To switch to one of the three sets of image settings programmed into the \
USER 
MEMORY buttons, then select using the   or   keys.
•
•
•
•
• 
						

							
Rev B December 2010 Page 4.7
Digital Projection M-Vision Cine LED User Manual 4. Controlling the projector

Image quality settings
Press any of the following keys on the remote control, followed by  and , to 
adjust these image quality settings:
 Brightness   
Contrast   
Sharpness   
Gamma   
Overscan   
Noise reduction 
Brilliant-color   
Colour temperature 
Example - Brightness screen control:
Test pattern
Press the  key repeatedly to cycle through the Test patterns, in the 
following order:
White, Black, Red, Green, Blue, Cyan, Magenta, Yellow, Chequerboard, 
Greyscale, Alignment grid, White...
•
•
Notes
  For more information about all 
these image quality settings, 
and more, see Main menu and 
Advanced menu later in this 
section, Using the menus. 
 Some of the settings will not be 
available for some of the input 
sources.  
						

							
Page 4.8 Rev B December 2010
4. Controlling the projector Digital Projection M-Vision Cine LED User Manual

Notes
 Some  menu controls can be 
accessed directly using the 
control keys (see earlier in this 
section).
 There is a 30 second timeout 
for the menu navigation keys. If 
a menu times out, simply press 
the Menu key again.
 The SELECT key on the 
projector control panel has 
exactly the same funtion as 
the ENTER key on the remote 
control.
 To exit from the menus 
completely, you may need to 
press  up to three times.
Using the menus
Navigating menus and submenus
The menus are organised into five pages. When the menus are in use, the \
menu 
page headings are always visible at the top of the menu panel.
Most menu items can be adjusted directly, but some items lead to a submenu.
The menus will always open at the same page that was last viewed. The example 
below shows the first menu page displayed following power on, which is a\
lways the 
Main menu.
Use the navigation keys on the remote control or the projector control p\
anel to 
navigate through the menus:
To display the menus, press MENU  on the remote control or the projector 
control panel.
To select a different menu page, use the  and  keys.
To select a menu item, use the  and  keys.
To close a menu, press MENU  again.
•
•
•
•
• 
						

							
Rev B December 2010 Page 4.9
Digital Projection M-Vision Cine LED User Manual 4. Controlling the projector

Notes
 To select a different menu, 
press MENU  once or 
twice, so that no items are 
highlighted, then use the the 
 and  keys to select a 
different page.
 To exit from the menus 
completely, you may need to 
press  up to three times.
 Image changes made using 
the menus will take effect 
immediately.
 Some menu items may be 
greyed out - unavailable due to 
the effect of settings made in 
other menus, or due to the type 
of input signal.
 For more information about 
the Aspect ratio settings, 
see Screen requirements in 
section 2. Installation.
Main menu
To display the menus, press MENU  on the remote control or the projector 
control panel.
Use the  and  keys to select the Main menu page,
To select a menu item, use the  and  keys until the item is highlighted.
Aspect Ratio
Use the  and  keys to select from:
16:9  the image is scaled to fill the DMD (and thus, a 16:9 screen).
Theaterscope the image is scaled such that a 2.35:1 image will be displayed 
at the correct aspect ratio when the projector is fitted with an 
anamorphic lens. Thus an image with an aspect ratio of 2.35:1 
can be displayed using the full 16:9 resolution of the DMD.
4:3   the image is scaled to fit a 4:3 screen, using the full height of the 
DMD.
4:3 Narrow  to be used for 4:3 images in combination with an anamorphic 
lens. The image is scaled to fit the DMD vertically, but squeezed 
horizontally such that the lens will stretch it to the correct ratio.
Native  the image is displayed with no scaling, at its original resolution, in 
the centre of the screen.
•
•
•
• 
						

							
Page 4.10 Rev B December 2010
4. Controlling the projector Digital Projection M-Vision Cine LED User Manual

Presets
Press ENTER or SELECT.
The Presets submenu will appear:
Use the  and  keys to select from:
Recall Presets
Save Presets
recall presets
Recall a set of image settings that have previously been saved to Preset\
s A, B, 
C or D.
Use the  or  keys to select which Preset is to be recalled. 
 Select Default, to recall the factory default settings.
Save presets
Save the the image settings for all seven inputs to the selected Preset.
Use the  or  keys to select which Preset the settings will be saved to.
The following settings will be saved:
Brightness    Contrast    Saturation
Hue     Sharpness    Noise Reduction
Color Space   Video Standard    Gamma
Colour Temperature Color Gamut    Brilliant Color
Adaptive Contrast RGB Offsets    RGB Gains
To return to the Main menu, press  once.
•
•
•
•
•
•
Notes
 To select a different menu, 
press MENU  once or 
twice, so that no items are 
highlighted, then use the the 
 and  keys to select a 
different page.
 To exit from the menus 
completely, you may need to 
press  up to three times.
 Image changes made using 
the menus will take effect 
immediately.
 The Presets can also be 
recalled using the USER 
MEMORY keys on the remote 
control. See Using the control 
keys earlier in this section.
  Note: Preset D is available only 
through the Control menu, not 
through the remote control.
 When Save Presets is 
selected, the image settings for 
ALL seven inputs are saved.
Main menu continued 
						

							
Rev B December 2010 Page 4.11
Digital Projection M-Vision Cine LED User Manual 4. Controlling the projector

Brightness
Press  or  once. 
After the first press, the Brightness adjustment bar will appear:
Use the  and  keys to adjust the Brightness from 0 to 200:
To return to the Main menu, press  once.
Contrast
Press  or  once. 
After the first press, the Contrast adjustment bar will appear.
Use the  and  keys to adjust the Contrast from 0 to 200:
To return to the Main menu, press  once.
Saturation
Saturation is the amount of colour in the image. Decrease this setting i\
f colors are 
too bright; increase it if colors appear muted or washed out.
Press  or  once. 
After the first press, the Saturation adjustment bar will appear.
Use the  and  keys to adjust the Saturation from 0 to 200:
To return to the Main menu, press  once.
Hue
Hue is the ratio of red to green in the image. Decrease this setting to \
shift the hue 
toward red; increase it to shift the hue toward green.
Press  or  once. 
After the first press, the Hue adjustment bar will appear.
Use the  and  keys to adjust the Hue from 0 to 200:
To return to the Main menu, press  once.
•
•
•
•
•
•
•
•
•
•
•
•
Notes
 To exit from the menus 
completely, you may need to 
press  up to three times.
 Image changes made using 
the menus will take effect 
immediately.
 Image changes made using 
the menus will take effect 
immediately.
 Some menu items may be 
greyed out - unavailable due to 
the effect of settings made in 
other menus, or due to the type 
of input signal.
 Image quality settings are often 
interactive - a change in one 
setting may require a change to 
be made in another setting.
 Setting Adaptive Contrast to 
On in the Advanced menu will 
affect any image quality settings 
made in other menus.
Main menu continued 
						

							
Page 4.12 Rev B December 2010
4. Controlling the projector Digital Projection M-Vision Cine LED User Manual

Notes
 To exit from the menus 
completely, you may need to 
press  up to three times.
 Image changes made using 
the menus will take effect 
immediately.
 Some menu items may be 
greyed out - unavailable due to 
the effect of settings made in 
other menus, or due to the type 
of input signal.
 When the Aspect Ratio is set 
to Native, Overscan can only 
be set to Off or Crop
Sharpness
Press  or  once. 
After the first press, the Sharpness adjustment bar will appear.
Use the  and  keys to adjust the Sharpness from 0 to 200:
To return to the Main menu, press  once.
Noise Reduction
Press  or  once. 
After the first press, the Noise reduction adjustment bar will appear.
Use the  and  keys to adjust the Noise reduction from 0 to 200:
To return to the Main menu, press  once.
Overscan
Some television programs are produced based on the assumption that older\
 
television sets may not display the outer edges of the broadcast picture\
 area. 
Consequently the edges of the image may be noisy or badly defined. Overs\
can is 
used to compensate for this, by hiding the outer edges of the image.
Use the  or  keys to select from:
Off
Crop blanks a 3% border from the left and right edges of the image
Zoom  increases the horizontal and vertical resolution of the displayed 
image by 6%, so that the all four edges fall outside the screen 
area
•
•
•
•
•
•
•
Main menu continued