Digital Projection M-vision Cine Led User Manual

							
Rev B December 2010 Page 6.13
Digital Projection M-Vision Cine LED User Manual 6. Appendix

Remote communications protocol
Introduction
The projector can be controlled by using an external control system or a\
 PC via an 
RS232 serial interface, using a terminal-emulation program, such as Hype\
rTerminal.
There are 2 types of commands:
Key commands
Operation commands
All commands consist of ascii text strings starting with 2 letters:
ky for key commands.
op for operations commands.
All commands end with an ascii Carriage Return character.
Key Commands
Key commands are used to simulate remote control key presses, and use th\
e 
following format:
ky  [CR]
Example
ky pow.on [CR] simulates the POWER ON key being pressed.
The commands
Code transmittedDescription
0x01pow.onTurn power on.
0x09pow.offTurn power off.
0x15menuBring up or cancel menu display.
0x17enterKeypad enter.
0x18cur.downKeypad down arrow.
0x1Acur.upKeypad up arrow.
0x1Dcur.leftKeypad left arrow.
0x1Fcur.righKeypad right arrow.
0x80brightBring up or cancel brightness slide bar.
0x81contrastBring up or cancel contrast slide bar.
•
•
•
•
Notes
 Details of how to connect to 
the projector, using the serial 
control input, can be found 
earlier in this section.
 Note: in the example, spaces 
are included for clarity, but are 
not necessary in the actual 
command. 
						

							
Page 6.14 Rev B December 2010
6. Appendix Digital Projection M-Vision Cine LED User Manual

Code transmittedDescription
0x82sharpBring up or cancel sharpness slide bar.
0x83nrBring up or cancel noise reduction slide bar.
0x85gam.swSwitch to the next gamma value.
0x8Bsrc.1Switch the active source to source 1.
0x8Csrc.2Switch the active source to source 2.
0x8Dsrc.3Switch the active source to source 3.
0x8Esrc.4Switch the active source to source 4.
0x8Fsrc.5Switch the active source to source 5.
0x93osc.swSwitch to the next Overscan mode.
0x98mem.1Recall user memory associated with the User Memory A key.
0x99mem.2Recall user memory associated with the User Memory B key.
0x9Amem.3Recall user memory associated with the User Memory C key.
0x9Dasp.swSwitch to the next aspect ratio setting.
0xA3bcolor.swSwitch Brilliant Color on or off.
0xAActemp.swSwitch to the next colour temperature value.
0xADpattern.swSwitch to the next test pattern. 
						

							
Rev B December 2010 Page 6.15
Digital Projection M-Vision Cine LED User Manual 6. Appendix

Operation Commands
Operation commands are used to simulate menu operations and determine th\
e 
settings of the projector, and use the following format:
op   [CR]
The  string can take one of the following formats:
Description
Set= Makes the setting take that value.
Get?Asks what the current value is.
The value is returned as an ascii text string.
Increment+Adds 1 to the current value.
Decrement-Subtracts 1 from the current value.
Execute(none)Performs an action.
Example
op aspect =1 [CR] sets the aspect ratio to Theaterscope.
op aspect ? [CR] asks what is the current aspect ratio.
op bright + [CR] increments the brightness setting.
op resync [CR] commands the projector to attempt to re-synchronise to the 
current input source.
The commands
OperationValuesNotes
aspect= ?0 = 16:9 
1 = Theaterscope 
2 = 4:3 
3 = 4:3 Narrow 
4 = Native
memory= ?0 = Preset A 
1 = Preset B 
2 = Preset C 
3 = Preset D 
4 = Default
save.mem=0 = Preset A 
1 = Preset B 
2 = Preset C 
3 = Preset D
bright= ? + -0 - 200
contrast= ? + -0 - 200
saturat= ? + -0 - 200
tint= ? + -0 - 200
sharp= ? + -0 - 200
noise.thresh= ? + -0 - 200
nr.simple= ? + -0 - 200
nr.mode= ?0 = Simple 
1 = Advanced
Notes
 Note: in the examples, spaces 
are included for clarity, but are 
not necessary in the actual 
command. 
						

							
Page 6.16 Rev B December 2010
6. Appendix Digital Projection M-Vision Cine LED User Manual

OperationValuesNotes
nr.general= ? + -0 - 200
block.reduct= ? + -0 - 200
mosq.noise= ? + -0 - 200
overscan= ?0 = Off 
1 = Crop 
2 = Zoom
source.sel= ?0 = HDMI 1 
1 = HDMI 2 
2 = RGB 
3 = YPrPb 1 
4 = YPrPb 2 
5 = S-Video 
6 = Video
resync(execute)
color.space= ?0 = Auto 
1 = YPbPr ( = REC709) 
2 = YCbCr ( = REC601) 
3 = RGB-PC 
4 = RGB-Video
video.stand= ?0 = Auto 
1 = NTSC 
2 = PAL 
3 = SECAM
gamma= ?0 = CRT 
1 = Film 
2 = Video 
3 = Punch 
4 = Graphics
color.temp= ?0 = 5500K 
1 = 6500K 
2 = 7500K 
3 = 9300K
dlp.frame= ?0 = Auto 
2 = 48 Hz 
3 = 50 Hz 
4 = 60 Hz
color.gamut= ?0 = Auto 
1 = REC709 
2 = SMPTE C 
3 = EBU 
4 = Native
bcolor= ?0 = Off 
1 = On
red.off= ? + -0-200
green.off= ? + -0-200
blue.off= ? + -0-200
red.gain= ? + -0-200
green.gain= ? + -0-200
blue.gain= ? + -0-200
vert.pos= ? + -0-200
horiz.pos= ? + -0-200 
						

							
Rev B December 2010 Page 6.17
Digital Projection M-Vision Cine LED User Manual 6. Appendix

OperationValuesNotes
phase= ? + -0-200
tracking= ? + -0-200
sync.level= ? + -0-200
menu.pos= ?0 = Top left 
1 = Top right 
2 = Bottom left 
3 = Bottom right 
4 = Centre
blank.screen= ?0 = Black 
1 = Blue 
2 = White 
3 = Logo
auto.pow.off= ?0 = Off 
1 = On
auto.pow.on= ?0 = Off 
1 = On
rear.proj= ?0 = Off 
1 = On
ceil.mode= ?0 = Off 
1 = On
logo.disp= ?0 = Off 
1 = On
trig.1= ?0 = Screen 
1 = 16:9 
2 = Theaterscope 
3 = 4:3 
4 = 4:3 Narrow 
5 = RS232 
6 = On 
7 = Off
0: Trigger occurs when the projector is in 
RUNNING mode
trig.2= ?0 = Screen 
1 = 16:9 
2 = Theaterscope 
3 = 4:3 
4 = 4:3 Narrow 
5 = RS232 
6 = On 
7 = Off
0: Trigger occurs when the projector is in 
RUNNING mode
auto.source= ?0 = Off 
1 = On
model.name?
ser.number?
soft.version?
act.source?0 = HDMI 1 
1 = HDMI 2 
2 = RGB 
3 = YPrPb 1 
4 = YPrPb 2 
5 = S-video 
6 = Video
h.refresh?KHz
v.refresh?Hz 
						

							
Page 6.18 Rev B December 2010
6. Appendix Digital Projection M-Vision Cine LED User Manual
OperationValuesNotes
pixel.clock?MHz
signal?
lamp.hours?
total.hours?
environment?Temperatures
fact.reset(execute)
blue.only=0 = Off 
1 = On
pattern=0 = White 
1 = Black 
2 = Red 
3 = Green 
4 = Blue 
5 = Cyan 
6 = Magenta 
7 = Yellow 
8 = Chequerboard 
9 = Greyscale 
10 = Alignment Grid 
11 = Off
altitude= ?0 = Low 
1 = High
status.check?0 = standby mode 
1 = warm up mode 
2 = running mode 
3 = cooling mode 
4 = error 
						

							
Digital Projection M-Vision Cine LED User Manual 
						

							
Digital Projection M-Vision Cine LED User Manual