Digital Projection M-vision Cine Led User Manual

							
Rev B December 2010 Page 4.23
Digital Projection M-Vision Cine LED User Manual 4. Controlling the projector

Rear Projection
Use the  and  keys to select from:
On   Projected image is reversed, left to right
Off
Ceiling Mode
Use the  and  keys to select from:
On   Projected image is reversed, top to bottom
Off
Logo Display
Use the  and  keys to select from:
On   The Digital Projection logo is displayed during power up
Off
•
•
•
Notes
 To exit from the menus 
completely, you may need to 
press  up to three times.
 Image changes made using 
the menus will take effect 
immediately.
System menu continued 
						

							
Page 4.24 Rev B December 2010
4. Controlling the projector Digital Projection M-Vision Cine LED User Manual

Notes
 To select a different menu, 
press MENU  once or 
twice, so that no items are 
highlighted, then use the the 
 and  keys to select a 
different page.
 To exit from the menus 
completely, you may need to 
press  up to three times.
 For more information about 
the trigger output, see Control 
connections in section 
6.  Appendix. 
 For more information about 
RS232 commands, see Remote 
communications protocol in 
section 6.  Appendix.
Control menu
To display the menus, press MENU  on the remote control or the projector 
control panel.
Use the  and  keys to select the Control menu page,
To select a menu item, use the  and  keys until the item is highlighted.
Trigger 1 & 2
The Trigger 1 and Trigger 2 outputs are interchangeable:
Screen trigger: can be connected to an electrically operated screen, 
automatically deploying the screen when the projector 
starts up, and retracting the screen when the projector 
shuts down.
Aspect Ratio trigger: can be used to control screen shuttering for different 
aspect ratios
For each Trigger setting, use the  and  keys to select from:
Screen  trigger occurs when the projector is in RUNNING mode
16:9  trigger occurs when 16:9 aspect ratio is selected
Theaterscope trigger occurs when Theaterscope aspect ratio is selected
4:3 trigger occurs when 4:3 aspect ratio is selected
4:3 Narrow trigger occurs when 4:3 Narrow aspect ratio is selected
 RS232 trigger output follows the On or Off setting specified in a trig.1 or 
trig.2 command received from a PC via the RS232 serial input.
•
•
•
• 
						

							
Rev B December 2010 Page 4.25
Digital Projection M-Vision Cine LED User Manual 4. Controlling the projector

Notes
 To set what a ‘blank’ screen 
looks like, use the Blank 
Screen setting in the System 
menu.
 To select a different menu, 
press MENU  once or 
twice, so that no items are 
highlighted, then use the the 
 and  keys to select a 
different page.
 To exit from the menus 
completely, you may need to 
press  up to three times.
 If a source has been disabled in 
the System menu, then a key 
programmed with that source 
will have no effect.
Auto Source
Use the  and  keys to select from:
On  projector searches for an alternative input source when the current 
input source is disconnected
Off projector shows a ‘blank’ screen when the current input source is 
disconnected
Keys 1 to 5
The  to   keys on the remote control can each be programmed to switch 
to one of the seven input sources.
 Use the  and  keys to select a Key, then press ENTER or SELECT.
The Key submenu will appear:
Use the  and  keys to select from:
HDMI 1
HDMI 2
RGB
Component 1
Component 2
Video
S-Video
Press ENTER or SELECT  to confirm your selection.
Press MENU  to return to the Control menu and select another key.
•
•
•
•
•
Control menu continued 
						

							
Page 4.26 Rev B December 2010
4. Controlling the projector Digital Projection M-Vision Cine LED User Manual

Notes
 To select a different menu, 
press MENU  once or 
twice, so that no items are 
highlighted, then use the the 
 and  keys to select a 
different page.
 To exit from the menus 
completely, you may need to 
press  up to three times.
 Restore Defaults will restore 
all settings to factory 
defaults.
  If you are not sure this is 
what you want to do, then 
either:
 make a record of all settings 
first 
 
or 
select No, then press ENTER or 
SELECT
Service menu
To display the menus, press MENU  on the remote control or the projector 
control panel.
Use the  and  keys to select the Service menu page,
The first eight items are for information only, and cannot be changed.
To select a menu item, use the  and  keys until the item is highlighted.
Factory Reset
Press ENTER or SELECT  to request a Factory Reset.
 The following message will be displayed.
Use the  and  keys to select from:
Yes   all settings will be restored to factory defaults
  No
Press ENTER or SELECT to confirm your choice.
•
•
•
•
• 
						

							
Rev B December 2010 Page 4.27
Digital Projection M-Vision Cine LED User Manual 4. Controlling the projector

Blue Only
This is useful for color-calibrating the projector or other video compon\
ents.
Use the  and  keys to select from:
On only the blue signal is displayed - green and red are turned off
Off    all three signals - red, green and blue - are displayed
Test Patterns
Use the  and  keys to select from:
Test Pattern Off
White
Black
Red
Green
Blue
Cyan
Magenta
Yellow
Chequerboard
Greyscale
Alignment grid
To turn the test pattern Off, press any other key.
Altitude
For use at high altitudes where the air is thinner, the fan speed can be increased.
Use the  and  keys to select from:
Low normal speed fan
High   high speed fan
•
•
•
•
Notes
 To exit from the menus 
completely, you may need to 
press  up to three times.
 Image changes made using 
the menus will take effect 
immediately.
 Some menu items may be 
greyed out - unavailable due to 
the effect of settings made in 
other menus, or due to the type 
of input signal.
 If the projector frequently 
overheats when used in a high 
altitude environment, then 
it may help to use the High 
Altitude setting.
  In most cases, the Low Altitude 
setting should be satisfactory.
Service menu continued 
						

							
Page 4.28 Rev B December 2010
4. Controlling the projector Digital Projection M-Vision Cine LED User Manual 
						

							
Rev B December 2010 Page 5.1
5. Maintenance
Contents
Changing the LED module ........................................................................\
.......................................5.2
Cleaning the fans ........................................................................\
........................................................5.2 
						

							
Page 5.2 Rev B December 2010
5. Maintenance Digital Projection M-Vision Cine LED User Manual
Changing the LED module
The LED module should be changed only by qualified and authorised servic\
e 
personnel.
Contact your Digital Projection Dealer.
•
•
Notes
 The LED module in this 
projector should be changed 
ONLY by authorised and 
qualified service personnel.
 Always switch the projector 
OFF before cleaning the fans.
  The fans should be cleaned 
regularly:
In a clean environment such as 
an office, after 500 hours.
In a dusty or smoky 
environment such as a theatre 
or public area, more frequent 
cleaning may be necessary.
•
•
Cleaning the fans
Turn the power OFF and wait until the fans stop.
Use a vacuum cleaner to clean the inlet and outlet fans, as shown below.
•
• 
						

							
Rev B December 2010 Page 6.1
6. Appendix
Contents
Troubleshooting ........................................................................\
..........................................................6.2
Error codes ........................................................................\
..............................................................6.4
Specifications ........................................................................\
..............................................................6.5
Part numbers ........................................................................\
............................................................6.5
Optical ........................................................................\
.....................................................................6.5
Electrical ........................................................................\
..................................................................6.6
Physical ........................................................................\
...................................................................6.6
Dimensions ........................................................................\
..................................................................6.7
Video formats supported ........................................................................\
..........................................6.8
Input connections ........................................................................\
.....................................................6.10
HDMI 1 & 2 inputs ........................................................................\
...................................................6.10
Composite video input ........................................................................\
.............................................6.10
S-Video input ........................................................................\
..........................................................6.10
RGB input ........................................................................\
...............................................................6.11
Component 1 input ........................................................................\
...................................................6.11
Component 2 input ........................................................................\
...................................................6.11
Control connections ........................................................................\
................................................6.12
Wired Remote control connection ........................................................................\
.............................6.12
Trigger 1 & 2 output ........................................................................\
................................................6.12
Serial control input ........................................................................\
..................................................6.12
Null-modem cable ........................................................................\
.................................................6.12
Serial port settings ........................................................................\
................................................6.12
Remote communications protocol ........................................................................\
.......................6.13
Introduction ........................................................................\
............................................................6.13
Key Commands ........................................................................\
......................................................6.13
Example ........................................................................\
.............................................................6.13
The commands ........................................................................\
....................................................6.13
Operation Commands ........................................................................\
.............................................6.15
Example ........................................................................\
.............................................................6.15
The commands ........................................................................\
....................................................6.15 
						

							
Page 6.2 Rev B December 2010
6. Appendix Digital Projection M-Vision Cine LED User Manual

Troubleshooting
problempossible solutions
The red ISSUE indicator is illuminated 
continuously or flashing.
Check the Error codes detailed on the next page.
The projector will not power up.Note that the blue POWER indicator light will be OFF when the projector \
is in 
normal RUNNING MODE.
Check that the mains plug is plugged in and that the mains supply is swi\
tched on.
Check any external fuses or breakers.
The projector will not power up shortly 
after being switched off.
To protect the LED module, the projector cannot be switched on when in it\
 is in 
cool-down mode. Wait until the power indicator shows steady blue. showing that it 
is in standby mode.
The projector shuts down after it has 
been in use for some time.
The projector may be overheating. Check that the air inlets and outlets \
are clear 
of any obstruction.
See section 5. Maintenance, Cleaning the fans
It is possible to increase the speed of the fans for use in a high altit\
ude 
environment:
See section 4. Controlling the projector, System menu
No image is displayed.Check that the input source is switched on and connected to the projecto\
r 
correctly.
Check that the correct image source is selected.
Check that the brightness and contrast settings are set correctly.
See section 4. Controlling the projector, Using the control keys and Main 
menu
The projector may be overheating. Check that the air inlets and outlets \
are clear 
of any obstruction.
The image does not fit the screen 
correctly.
Check that the projector and screen size are positioned correctly, and that the 
zoom is adjusted correctly.
See section 2. Installation, Screen size vs throw distance
Check the aspect ratio setting.
See section 4. Controlling the projector, Main menus
Uneven image quality.Check that the projector is parallel to the screen.
Check that the screen is flat, and securely mounted.