Digital Projection M-vision 1080p-260 User Manual

Rev A May 2010 Page 6.13
Digital Projection M-Vision 1080p-260 User Manual  6. Appendix

Remote communications protocol
Introduction
The projector can be controlled by using an external control system or a PC via an 
RS232 serial interface, using a terminal-emulation program, such as HyperT erminal.
There are 2 types of commands:
Key commands
Operation commands
All commands consist of ascii text strings starting with 2 letters:
ky for key commands.
op for operations commands.
All commands end with an...

Page 6.14  Rev A May 2010
6. Appendix  Digital Projection M-Vision 1080p-260 User Manual

Code transmittedDescription
0x82sharpBring up or cancel sharpness slide bar.
0x83nrBring up or cancel noise reduction slide bar.
0x85gam.swSwitch to the next gamma value.
0x8Bsrc.1Switch the active source to source 1.
0x8Csrc.2Switch the active source to source 2.
0x8Dsrc.3Switch the active source to source 3.
0x8Esrc.4Switch the active source to source 4.
0x8Fsrc.5Switch the active source to source 5....

Rev A May 2010 Page 6.15
Digital Projection M-Vision 1080p-260 User Manual  6. Appendix

Operation Commands
Operation commands are used to simulate menu operations and determine th\
e 
settings of the projector, and use the following format:
op   [CR]
The  string can take one of the following formats:
Description
Set= Makes the setting take that value.
Get?Asks what the current value is.
The value is returned as an ascii text string.
Increment+Adds 1 to the current value.
Decrement-Subtracts 1 from the...

Page 6.16  Rev A May 2010
6. Appendix  Digital Projection M-Vision 1080p-260 User Manual

OperationValuesNotes
nr.general= ? + -0 - 200
block.reduct= ? + -0 - 200
mosq.noise= ? + -0 - 200
overscan= ?0 = Off 
1 = Crop 
2 = Zoom
source.sel= ?0 = HDMI 1 
1 = HDMI 2 
2 = RGB 
3 = YPrPb 1 
4 = YPrPb 2 
5 = S-Video 
6 = Video
resync(execute)
color.space= ?0 = Auto 
1 = YPbPr ( = REC709) 
2 = YCbCr ( = REC601) 
3 = RGB-PC 
4 = RGB-Video
video.stand= ?0 = Auto 
1 = NTSC 
2 = PAL 
3 = SECAM
gamma= ?0 = CRT 
1 =...

Rev A May 2010 Page 6.17
Digital Projection M-Vision 1080p-260 User Manual  6. Appendix

OperationValuesNotes
phase= ? + -0-200
tracking= ? + -0-200
sync.level= ? + -0-200
menu.pos= ?0 = Top left 
1 = Top right 
2 = Bottom left 
3 = Bottom right 
4 = Centre
blank.screen= ?0 = Black 
1 = Blue 
2 = White 
3 = Logo
auto.pow.off= ?0 = Off 
1 = On
auto.pow.on= ?0 = Off 
1 = On
rear.proj= ?0 = Off 
1 = On
ceil.mode= ?0 = Off 
1 = On
logo.disp= ?0 = Off 
1 = On
trig.1= ?0 = Screen 
1 = 16:9 
2 = Theaterscope...

Page 6.18  Rev A May 2010
6. Appendix  Digital Projection M-Vision 1080p-260 User Manual
OperationValuesNotes
pixel.clock?MHz
signal?
lamp.hours?
total.hours?
environment?Temperatures
lamp reset(execute)
fact.reset(execute)
blue.only=0 = Off 
1 = On
pattern=0 = White 
1 = Black 
2 = Red 
3 = Green 
4 = Blue 
5 = Cyan 
6 = Magenta 
7 = Yellow 
8 = Chequerboard 
9 = Greyscale 
10 = Alignment Grid 
11 = Off
altitude= ?0 = Low 
1 = High
status.check?0 = standby mode 
1 = warm up mode 
2 = running mode 
3 =...

Digital Projection M-Vision 1080p-260 User Manual 

Digital Projection M-Vision 1080p-260 User Manual