Digital Projection M-vision 1080p-260 User Manual

Rev A May 2010 Page 4.23
Digital Projection M-Vision 1080p-260 User Manual  4. Controlling the projector

Notes
 To select a different menu, 
press MENU  once or 
twice, so that no items are 
highlighted, then use the the 
 and  keys to select a 
different page.
 To exit from the menus 
completely, you may need to 
press  up to three times.
 For more information about 
the trigger input, see Control 
connections in section 
6.  Appendix
. 
 For more information about 
RS232 commands, see Remote...

Page 4.24  Rev A May 2010
4. Controlling the projector  Digital Projection M-Vision 1080p-260 User Manual

Notes
 To set what a ‘blank’ screen 
looks like, use the Blank 
Screen setting in the System 
menu.
 To select a different menu, 
press MENU  once or 
twice, so that no items are 
highlighted, then use the the 
 and  keys to select a 
different page.
 To exit from the menus 
completely, you may need to 
press  up to three times.
 If a source has been disabled in 
the System menu, then a key...

Rev A May 2010 Page 4.25
Digital Projection M-Vision 1080p-260 User Manual  4. Controlling the projector

Notes
 To select a different menu, 
press MENU  once or 
twice, so that no items are 
highlighted, then use the the 
 and  keys to select a 
different page.
 To exit from the menus 
completely, you may need to 
press  up to three times.
 Restore Defaults will restore 
all settings to factory 
defaults.
  If you are not sure this is 
what you want to do, then 
either:
 make a record of all settings...

Page 4.26  Rev A May 2010
4. Controlling the projector  Digital Projection M-Vision 1080p-260 User Manual
Blue Only
This is useful for color-calibrating the projector or other video components.
Use the  and  keys to select from:
On  only the blue signal is displayed - green and red are turned off
Off    all three signals - red, green and blue - are displayed
Test Patterns
Use the  and  keys to select from:
Test Pattern Off
White
Black
Red
Green
Blue
Cyan
Magenta
Yellow
Chequerboard
Greyscale
Alignment...

Rev A May 2010  Page 5.1
5. Maintenance
Contents
Changing the lamp module ..............................................................................................................5.2
Cleaning the fans ................................................................................................................................5.3 

Page 5.2  Rev A May 2010
5. Maintenance  Digital Projection M-Vision 1080p-260 User Manual

Changing the lamp module
Turn the power OFF and allow the lamp to cool for 5 minutes.
Unscrew the captive finger screw securing the lamp door, and remove the door.
Unscrew the two cross-head screws securing the lamp module to the projector
Lift the wire handle up and use it to pull out the lamp module.
Fit a new lamp module, pushing it firmly into place.
Tighten the two cross-head screws.
Locate the two lugs at...

Rev A May 2010 Page 5.3
Digital Projection M-Vision 1080p-260 User Manual  5. Maintenance

Cleaning the fans
Turn the power OFF and wait until the fans stop.
Use a vacuum cleaner to clean the inlet and outlet fans, as shown below .
•
•
Notes
 Always switch the projector 
OFF before cleaning the fans.
  The fans should be cleaned 
regularly:
In a clean environment such as 
an office, after 500 hours.
In a dusty or smoky 
environment such as a theatre 
or public area, more frequent 
cleaning may be...

Page 5.4  Rev A May 2010
5. Maintenance  Digital Projection M-Vision 1080p-260 User Manual 

Rev A May 2010  Page 6.1
6. Appendix
Contents
Troubleshooting ..................................................................................................................................6.2
Error codes ......................................................................................................................................6.4
Specifications ......................................................................................................................................6.5
Part...

Page 6.2  Rev A May 2010
6. Appendix  Digital Projection M-Vision 1080p-260 User Manual

Troubleshooting
problempossible solutions
The red ISSUE indicator is illuminated 
continuously	or	flashing.Check the Error codes detailed on the next page.
The projector will not power up.Check that the mains plug is plugged in and that the mains supply is swi\
tched on.
Check that the lamp door is closed properly.
Check any external fuses or breakers.
The projector will not power up shortly 
after being switched...