Digital Projection M-vision 1080p-260 User Manual

Rev A May 2010 Page 2.13
Digital Projection M-Vision 1080p-260 User Manual  2. Installation

Notes
 For more information on 
selecting an input source, see 
section 4. Overview, Using 
the control keys, and Using 
the menus.
  For more information about pin 
connections and control codes 
see section 6. Appendix.
Connecting the projector
Signal Inputs
The following inputs are available:
HDMI 1 & 2  HDCP-compliant digital video inputs from HDMI or DVI sources.
RGB  15 pin D-type VGA style input from...

Page 2.14  Rev A May 2010
2. Installation  Digital Projection M-Vision 1080p-260 User Manual

Input connection examples, continued
Notes
  For more information about pin 
connections and control codes 
see section 6. Appendix. 

Rev A May 2010 Page 2.15
Digital Projection M-Vision 1080p-260 User Manual  2. Installation

Notes
 
 For more information about pin 
connections and control codes 
see section 6. Appendix.
Control connections
The following connections are available:
remote control
If infrared signals from the remote control cannot reach the projector due to 
excessive distance or obstructions such as walls or cabinet doors, you can connect 
an external IR repeater to the Remote control input, and position its IR sensor...

Page 2.16  Rev A May 2010
2. Installation  Digital Projection M-Vision 1080p-260 User Manual
Power connection
Lift the cable lock up, push the mains connector in firmly, then push the lock down to 
secure the cable.
Notes
 Use only the power cable 
provided.
 Ensure that the power 
outlet includes a Ground 
connection, as this 
equipment MUST be earthed.
 Handle the power cable 
carefully and avoid sharp 
bends. Do not use a damaged 
power cable.
Power 
connection 

Rev A May 2010  Page 3.1
3. Getting Started
Contents
Positioning the screen and projector ............................................................................................3.2
Switching the projector on ...............................................................................................................3.2
Inserting batteries into the remote control ...................................................................................3.2
Selecting an input signal or test pattern...

Page 3.2  Rev A May 2010
3. Getting Started  Digital Projection M-Vision 1080p-260 User Manual

Switching the projector on
Connect the power cable between the mains supply and the projector .
Wait until the self-test has completed and the standby indicator on the projector 
control panel shows amber. The lamp will be off and the projector will be in 
STANDBY mode.
Press POWER ON  on the remote control or POWER  on the projector 
control panel to switch the projector ON. The power indicator on the...

Rev A May 2010 Page 3.3
Digital Projection M-Vision 1080p-260 User Manual  3. Getting Started

Selecting an input signal or test pattern
Input
Connect an video source to the projector. The signal should be automatically 
detected by the projector, and should be displayed within a two or three 
seconds.
If more than one signal is connected to the projector, then select which signal 
is to be displayed, using the  to   buttons on the remote control, or 
by pressing the SOURCE button on the projector...

Page 3.4  Rev A May 2010
3. Getting Started  Digital Projection M-Vision 1080p-260 User Manual
Adjusting the projected image
Aspect ratio
Press  on the remote control until the image is displayed in the corect aspect\
 
ratio.
Image quality settings
Press any of the following keys on the remote control, followed by  and , to 
adjust these image quality settings:
 Brightness   
Contrast   
Sharpness   
•
•
Notes
  For more detailed information 
about:
  - using all the control keys 
on the remote control...

Rev A May 2010  Page 4.1
4. Controlling the projector
Contents
Overview ...............................................................................................................................................4.3
Controlling the projector.....................................................................................................................4.3
The control panel...

Page 4.2  Rev A May 2010
4. Controlling the projector  Digital Projection M-Vision 1080p-260 User Manual

Adaptive Contrast ...........................................................................................................................4.16
RGB Adjust ....................................................................................................................................4.17
Offsets...