Digital Projection Lightning 35/40hd-t, 30/40sx+m, 30/40sx+c User Manual

							
January 2007    Page 1
LIGHTNING   35/40HD-T,  30/40sx+m,  30/40sx+c
page 3Super High Brightness Digital Video Projector
Important Information
seite 9 Super High Brightness Digitaler
Videoprojektor
Wichtige Informationen
page 15 Vidéo projecteur numérique à forte luminosité
Informations importantes
página 21 Vídeo-proyector digital de alta luminosidad
Información importante
pagina 27 Proiettore video digitale ad alta luminosità
Informazioni importanti
sid. 33 Digital videoprojektor Super High Brightness
Viktig information
105-451B 
						

							
January 2007     Page 2
Digital Projection LIGHTNING   35/40HD-T,   30/40sx+m,   30/40sx+c
Digital Projection
Digital Projection Limited,
Greenside Way, Middleton, Manchester M24 1XX, UK.
Registered in England No. 2207264, Registered Office: as above
Tel +44 (0) 161 947 3300
Fax +44 (0) 161 684 7674
Email [email protected], [email protected]
Web Site www.digitalprojection.co.uk
Digital Projection Inc.
55 Chastain Road, Suite 115, Kennesaw, GA 30144. USA
Tel (USA) 770 420 1350
Fax (USA) 770 420 1360
Email  [email protected]
Web Sitewww.digitalprojection.com 
						

							
January 2007    Page 3
English Digital Projection LIGHTNING   35/40HD-T,   30/40sx+m,   30/40sx+c
This information booklet contains the following extracts from the User
Manual:
Contents
Symbols used in the User Manual ........................................................................\
............ 3
Declaration of Conformity ........................................................................\
......................... 4
General precautions ........................................................................\
.................................. 5
Installation precautions ........................................................................\
............................. 6
Operation and configuration  precautions ....................................................................... 7
Compliance with international st andards........................................................................\
 7
Noise ........................................................................\
.................................................. ............................... 7
RF Interference ........................................................................\
........................................ ......................... 7
Specifications........................................................................\
......................................... .... 7
Part numbers........................................................................\
........................................... ......................... 7
Optical ........................................................................\
................................................ ............................... 8
Electrical ........................................................................\
............................................. .............................. 8
Physical ........................................................................\
............................................... ............................. 8
Full information about operating, connecting and setting up the projecto\
r can be found in
the User Manual, located on the CD.
Symbols used in the User Manual
ELECTRICAL WARNING: this symbol indicates that there is a danger of electrical shock\
 unless the instructions
are closely followed.
WARNING: this symbol indicates that there is a danger of physical injury \
to yourself and/or damage to the
equipment unless the instructions are closely followed.
NOTE: this symbol indicates that there is some important information that you should read. 
						

							
January 2007     Page 4
Declaration of Conformity
Directives covered by this Declaration
89/336/EEC Electromagnetic Compatibility Directive, amended by  92/31/EEC and 93/68/EEC .
73/23/EEC  Low Voltage Equipment Directive, amended by  93/68/EEC.
Products covered by this Declaration
Large screen video projector type The CE mark was first applied in:
LIGHTNING 35HD-T February 2006
LIGHTNING 40HD-T August 2006
LIGHTNING 30sx+m October 2005
LIGHTNING 40sx+m September 2006
LIGHTNING 30sx+c October 2005
LIGHTNING 40sx+c September 2006
Basis on which Conformity is being declared
The products identified above comply with the protection requirements of the above EU directives, and the manufacturer has
applied the following standards.
EN 55022:1998 - Limits and Methods of Measurement of Radio Disturbance Characteristics of Inf\
ormation Technology
Equipment.
EN 55024:1998 - Limits and Methods of Measurement of Immunity Characteristics of Information \
Technology Equipment.
EN 55103:1997 - Product family Standard for Audio, Video, Audio-Visual and Entertainment Lighting Control apparatus for
Professional Use.
EN 60950:2000 - Specification for Safety of Information Technology Equipment, including Electrical Business equipment.
The technical documentation required to demonstrate that the products meet the requirements of the Low Voltage directive has
been compiled by the signatory below and is available for inspection by \
the relevant enforcement authorities.
Signed:
Authority: D.J. Quinn, Product Development Director
Date: 4 September 2006
Attention!
The attention of the specifier, purchaser, installer, or user is drawn to special measures and limitations to use which must be
observed when these products are taken into service to maintain compliance with the above directives. Details of these special
measures are available on request, and are also contained in the product manuals.
Digital Projection LIGHTNING   35/40HD-T,   30/40sx+m,   30/40sx+cEnglish 
						

							
January 2007    Page 5
General precautions
Do not open the cabinet. There are no user serviceable parts inside.
Use only the power cable provided.
Ensure that the power outlet includes a Ground connection, as this equip\
ment MUST be earthed.
Take care to prevent small objects such as paper or wire from falling into the projector. If this does happen,
switch off immediately, and have the objects removed by authorised service personnel.
Do not expose the projector to rain or moisture, and do not place any li\
quids on top of the projector.
Unplug before cleaning, and use a damp, not wet, cloth.
Do not touch the power plug with wet hands.
Do not touch the power plug during a thunder storm.
Handle the power cable carefully and avoid sharp bends. Do not use a dam\
aged power cable.
There are no user-serviceable parts inside the lamp module. The whole module should be replaced and return\
ed
to Digital Projection for re-furbishment.
Take care when removing the lamp module, as it is heavy (>10kg).
Take care not to touch the glass surface of the lamp module. If you do ac\
cidentally touch the glass, it should be
cleaned before use.
Do not use the lamp for more than 750 hours, as this may cause serious l\
amp failure, damage the lamp module
and cause extra cost on replacement.
Xenon lamps produce high intensity light. Do not look directly at the li\
ght coming from the lamp housing, or the
lens, or allow items such as magnifying lenses to be placed in the light\
 path. This could result in serious eye
damage.
Do not touch the ventilation outlets, as they will become hot in use.
Do not cover the ventilation outlets or inlets.
Do not cover the lens whilst the projector is switched on. This could ca\
use a fire
Always allow the projector to cool for 5 minutes before switching off th\
e power, moving the projector or
changing the lamp.
Never use strong detergents or solvents such as alcohol or thinners to clean the projector and lens.
English Digital Projection LIGHTNING   35/40HD-T,   30/40sx+m,   30/40sx+c 
						

							
January 2007     Page 6
Digital Projection LIGHTNING   35/40HD-T,   30/40sx+m,   30/40sx+cEnglish
Installation precautions
Connect the LAN cable only to a computer LAN connection. Other similar c\
onnectors may have a dangerously
high voltage source.
The projector must be installed only by suitably qualified personnel, in accordance with local building codes.
The projector should be installed as close to the power outlet as possible.
The power connection should be easily accessible, so that it can be disc\
onnected in an emergency.
Ensure that there is at least 30cm (12in) of space between the ventilation outlets and any wall, and 10cm (4in) on
all other sides.
Do not install the projector close to anything that might be affected by its operational heat, for instance,
polystyrene ceiling tiles, curtains etc.
The projector weighs over 100kg (200lbs). Use safe handling techniques\
 when lifting the projector.
When stacking projectors, the stack MUST be vertical, to ensure that the stresses are distributed to all\
 for frame
couplings.
Before installation, make sure that the surface, ceiling or rigging that is to supp\
ort the projector is capable of
supporting the combined weight of the projector and lens (see specification for exact weights).
Separate backup safety chains or wires should always be used for each proje\
ctor.
Do not place heavy objects on top of the projector chassis. Only the rigging frame is capable of withstanding the
weight of another projector.
Do not stack more than four projectors.
Do not drop or jarr the projector.
Place the projector in a dry area away from sources of dust, moisture, s\
team, smoke, sunlight or heat.
Each time a new lens is fitted to the projector, the calibration procedure must be carried out. See  Lens menu, in
Section 4. Using the menus .
The zoom drive mechanism should always be set to the engaged position, e\
ven when using the non-zoom lens,
as it provides an extra level of protection, should the lens release lev\
er fail.
Do not tilt the projector more than  ±12° from side to side when i\
n use, as this may cause serious lamp failure,
damage the lamp module and cause extra cost on replacement. The projecto\
r my be tilted forwards and
backwards as necessary.
±12° 360° 
						

							
January 2007    Page 7
English Digital Projection LIGHTNING   35/40HD-T,   30/40sx+m,   30/40sx+c
Operation and configuration precautions
Do not try to operate the touch screen using anything harder than your f\
inger. This could damage the LCD.
Do not make changes to the networking configuration unless you understand what you are doing, or have taken
advice from your Network Manager. If you make a mistake, it is possible that you will lose contact with the
projector. Always double-check your settings before pressing the APPLY button. Always keep a written note
of the original settings, and any changes you have made.
Software update should NOT be carried out except by, or with the supervision of, Digital Projection Service
personnel.
Compliance with international standards
Noise
GSGV Acoustic Noise Information Ordinance
The sound pressure level is less than 70 dB (A) according to ISO 3744 \
or ISO 7779.
RF Interference
FCC
The Federal Communications Commission does not allow any modifications o\
r changes to the unit EXCEPT those specified by
Digital Projection in this manual. Failure to comply with this government reg\
ulation could void your right to operate this
equipment.
This equipment has been tested and found to comply with the limits for a\
 Class A digital device, pursuant with Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interfer\
ence when the equipment is
operated in a commercial environment. This equipment generates, uses, an\
d can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause \
harmful interference to radio communications.
Operation of this equipment in a residential area may cause harmful inte\
rference, in which case the user will be responsible for
correcting any interference.
European Waste Electrical and Electronic Equipment (WEEE) Directive
Digital Projection Ltd is fully committed to minimising Waste Electrical and Electronic Equipment. Our products are
designed with reuse, recycling and recovery of all components in mind. To this end, at end of life, your projector may be
returned to Digital Projection Ltd or its agent so that the environmental impact can be minimised.
Specifications
Part numbers
Projector
USA model 35HD-T: 105-033 30sx+m: 107-148 30sx+c: 105-838
40HD-T : 106-264 40sx+m: 107-150 40sx+c: 106-692
Rest of World model 35HD-T: 105-034 30sx+m: 107-149 30sx+c: 105-839
40HD-T : 106-265 40sx+m: 107-151 40sx+c: 106-693 
						

							
January 2007     Page 8
Digital Projection LIGHTNING   35/40HD-T,   30/40sx+m,   30/40sx+cEnglish
Lenses 35/40HD-T
1.0 :1 fixed lens 103-350
1.25 - 1.45 :1 zoom lens 103-351
1.45 - 1.8 :1 zoom lens 102-451
1.8 - 2.4 :1 zoom lens 102-676
2.2 - 3.0 :1 zoom lens 102-677
3.0 - 4.3 :1 zoom lens 102-678
4.3 - 6.0 :1 zoom lens 104-189
Lenses 30/40sx+c
0.73 : 1 fixed lens 105-863
1.45 - 1.82 : 1 zoom lens 105-834
1.82 - 2.55 : 1 zoom lens 105-835
2.55 - 4.54 : 1 zoom lens 105-836
4.54 - 7.27 : 1 zoom lens 105-864Lenses 30/40sx+m
0.73 : 1 fixed lens 107-141
1.2 : 1 fixed lens (3 - 15m) 107-142
1.2 : 1 fixed lens (1.2 - 2m) 107-143
1.5 - 2.02 : 1 zoom lens 107-144
2.02 - 2.77 : 1 zoom lens 107-145
2.77 - 4.51 : 1 zoom lens 107-146
4.51 - 7.53 : 1 zoom lens 107-147
Replacement parts
Lamp module 35HD-T,  30sx+m,  30sx+c: 103-23840HD-T,  40sx+m,  40sx+c : 104-578
Air filter, complete replacement 104-154
Air filter, replacement filling only 105-222
Optical
Digital Light Processor sx+m, sx+c : 3 x 0.94” Texas Instruments DMD™, resolution 1400 x 1050 pixels
HD-T : 3 x 1.26” Texas Instruments DMD™, resolution 2048 x 1080 pixels
Contrast Ratio sx+m, sx+c : 1800:1 full field (±10%)HD-T: 1600:1 full field (±10%)
Pixel fill factor 87%
Lamp power 35HD-T,  30sx+m,  30sx+c : 3kW40HD-T,  40sx+m,  40sx+c : 3.6kW
Lamp life  (typical) 750 hours
Brightness 35HD-T,  30sx+m,  30sx+c : 18,000 Center lumens, 16,000 ANSI lumens (±10%)
40HD-T,  40sx+m,  40sx+c : 22,000 Center lumens, 21,000 ANSI lumens (±10%)
Colour temperature 3000-9300°K
Electrical
Inputs HD-T, sx+m, sx+c :  1 x DVI-D single
HD-T :  and 1 x DVI-D single, DVI-D dual, DVI-D single twin or DVI-D dual twi\
n
Pixel clock single: up to 165MHz, dual: up to 220MHz
Outputs 1 x DVI-D single loop through
Control inputs 1 x LAN
1 x Wireless LAN
1 x RS232 serial
Mains voltage 200-240 VAC, 50/60Hz (single phase)
Power consumption 35HD-T,  30sx+m,  30sx+c :  4000W40HD-T,  40sx+m,  40sx+c : 4600W
International Regulations Meets FCC Class A  requirements
Meets EMC Directives (EN 50081-1, EN 50082-1, EN 55022)
Meets Low Voltage Directive (EN60950)
Physical
Operating Temperature10 to 35°C
Storage Temperature -10 to 50°C
Thermal Dissipation 35HD-T,  30sx+m,  30sx+c : 13640 BTU/hr40HD-T,  40sx+m,  40sx+c : 15695 BTU/hr
Operating Humidity up to 80% non-condensing
Weight 114kg (249lbs) 
						

							
January 2007    Page 9
Deutsche Digital Projection LIGHTNING   35/40HD-T,   30/40sx+m,   30/40sx+c
Dieses Informationsheft enthält die folgenden Auszüge aus dem
Benutzerhandbuch:
Inhalt
Symbol in diesem Leitfaden ........................................................................\
...................... 9
Konformitätserklärung ........................................................................\
............................ 10
Allgemeine Vorsichtsmaßnahmen ........................................................................\
.......... 11
Vorsichtsmaßnahmen bei der  Installation ..................................................................... 12
Vorsichtsmaßnahmen bei Betrieb und Konfiguration .................................................. 13
Übereinstimmung mit internationalen St andards......................................................... 13
Lärm ........................................................................\
................................................... ............................. 13
Funkstörung ........................................................................\
............................................ ....................... 13
Technische Daten........................................................................\
.................................... 13
Teilenummern ........................................................................\
........................................... ...................... 13
Optisch ........................................................................\
................................................ ............................ 14
Elektrisch ........................................................................\
............................................. ........................... 14
Physisch ........................................................................\
............................................... .......................... 14
Vollständige Informationen über den Betrieb, den Anschluss und die Einstellungen des
Projektors finden Sie im Benutzerhandbuch auf der CD.
Symbol in diesem Leitfaden
ELEKTRISCHE  WARNUNG: Dieses Symbol weist darauf hin, dass Stromschlaggefahr besteht, wenn die
Anweisungen nicht strikt befolgt werden.
WARNUNG: Dieses Symbol weist darauf hin, dass die Gefahr von Körper- u\
nd Sachschäden besteht, wenn die
Anweisungen nicht strikt befolgt werden.
HINWEIS: Dieses Symbol weist auf wichtige Informationen hin, die Sie les\
en sollten. 
						

							
January 2007     Page 10
Digital Projection LIGHTNING   35/40HD-T,   30/40sx+m,   30/40sx+cDeutsche
Konformitätserklärung
Richtlinien, die durch diese Erklärung gedeckt sind
89/336/EWG-Richtlinie über elektromagnetische Verträglichkeit, geändert durch 92/31/EWG und 93/68/EWG.
73/23/EWG Niederspannungsrichtlinie, geändert durch 93/68/EWG.
Produkte, die durch diese Erklärung gedeckt sind.
Großschirm-Videoprojektor Typ Das CE-Gütezeichen wurde erstmals angebracht:
LIGHTNING 35HD-TFebruar 2006
LIGHTNING 40HD-T August 2006
LIGHTNING 30sx+m Oktober 2005
LIGHTNING 40sx+m September 2006
LIGHTNING 30sx+c Oktober 2005
LIGHTNING 40sx+c September 2006
Basis, auf der die Konformität erklärt wird
Die oben genannten Produkte stimmen mit den Schutzanforderungen der oben\
 aufgeführten  EU-Richtlinien überein, und der
Hersteller hat die folgenden Normen angewandt:
EN 55022:1998 - Grenzwerte und Messverfahren für Funkstörungen von\
 Einrichtungen der Informationstechnik.
EN 55024:1998 - Einrichtungen der Informationstechnik - Störungseigenschaften - Grenzwerte und Messverfahren.
EN 55103:1997 - Produktfamiliennorm für Audio-, Video-, und audiovisuelle Einrichtungen sowie für Studio-
Lichtsteuereinrichtungen für professionellen Einsatz.
EN 60950:2000 - Sicherheitsstandard für Geräte der Informationstechnologie, einschließlic\
h professionelle Geräte.
Die erforderliche technische Dokumentation für den Nachweis, dass die Produkte die Anforderungen der
Niederspannungsrichtlinie erfüllen, wurde durch den unten stehenden Unterzeic\
hner zusammengetragen und ist zur Einsicht
durch die vollziehenden Behörden verfügbar.
Unterzeichner:
Autorität: D.J. Quinn, Product Development Director
Datum: 4. September 2006
Achtung!
Der jeweilige Käufer, Installierer oder Benutzer wird auf spezielle Maßnahmen und Beschränku\
ngen hingewiesen, die zu
berücksichtigen sind, wenn diese Produkte in Betrieb genommen werden,\
 um die Einhaltung der oben aufgeführten Richtlinien
zu gewährleisten. Details dieser speziellen Maßnahmen sind auf Anfrage verfügbar und sind ebenfalls in den
Produkthandbüchern enthalten.